Cisco ONS 15310-MA SDH Manual

CHAPTER

1-1

Cisco ONS 15310-MA SDH Procedure Guide, R9.0

78-18668-01

Install the Cisco ONS 15310-MA SDH

This chapter provides procedures for installing the Cisco ONS 15310-MA SDH shelf, cards, and

fiber-optic cable. To view a summary of the tools and equipment required for installation, see the

“Required Tools and Equipment” section on page 1-3.

Before You Begin

This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).

1. NTP-H149 Unpack and Inspect the ONS 15310-MA SDH Shelf Assembly, page 1-5—Complete

this procedure before continuing with the “NTP-H150 Install the Shelf Assembly” procedure on

page 1-5.

2. NTP-H150 Install the Shelf Assembly, page 1-5—Complete this procedure to install the shelf

assembly in a rack before continuing with the “NTP-H151 Install the Power and Ground” procedure

on page 1-12 or before completing one of the following optional procedures.

3. NTP-H169 Install the Cable Management Bracket, page 1-6—As needed, complete this procedure

to install the cable management bracket.

4. NTP-H166 Remove the Blank Sheet Metal Covers, page 1-9—As needed, complete this procedure

to access the backplane.

5. NTP-H167 Install the EIAs, page 1-10—As needed, complete this procedure to install the electrical

interface assemblies (EIAs) before continuing with the “NTP-H151 Install the Power and Ground”

procedure on page 1-12.

6. NTP-H151 Install the Power and Ground, page 1-12—Complete this procedure before continuing

with the “NTP-H152 Install the Fan-Tray Assembly” procedure on page 1-14.

7. NTP-H152 Install the Fan-Tray Assembly, page 1-14—Complete this procedure before continuing

with the “NTP-H153 Install the 15310E-CTX-K9 Cards” procedure on page 1-16.

8. NTP-H153 Install the 15310E-CTX-K9 Cards, page 1-16—Complete this procedure to install the

common- control/cross-connect cards.

9. NTP-H154 Install the Ethernet Cards, page 1-19—As needed, complete this procedure to install an

Ethernet card.

10. NTP-H187 Install STM-N Cards and Connectors, page 1-20—As needed, complete this procedure

to install STM-N cards and connectors.

11. NTP-H155 Install the Electrical Cards, page 1-23—As needed, complete this procedure to install an

electrical card.

1-2

Cisco ONS 15310-MA SDH Procedure Guide, R9.0

78-18668-01

Chapter 1 Install the Cisco ONS 15310-MA SDH

Before You Begin

12. NTP-H156 Install the Filler Cards, page 1-24—As needed, complete this procedure to install a filler

card (blank faceplate) in the expansion slot. If no Ethernet or electrical card is installed in the

expansion slot, you must install a filler card.

13. NTP-H157 Install Wires to Alarm, Timing, Craft, LAN, and UDC Pin Connections,

page 1-25—Complete this procedure to install cables for alarms, timing, LAN, craft, and user data

channel (UDC) connections.

14. NTP-H158 Install the Electrical Cables, page 1-26—Complete this procedure to connect and route

cables that will carry electrical traffic.

15. NTP-H159 Install and Remove SFPs, page 1-27—As needed, complete this procedure to install

Small Form-factor Pluggables (SFPs) that provide a fiber-optic interface to the 15310E-CTX-K9

card.

16. NTP-H160 Install Optical Cables, page 1-28—Complete this procedure to connect and route cables

that will carry optical traffic.

17. NTP-H164 Perform the Shelf Installation Acceptance Test, page 1-30—Complete this procedure to

determine if you have correctly completed all other procedures in the chapter.

18. NTP-H161 Preprovision an SFP Slot, page 1-31—As needed, complete this procedure to

preprovision SFPs, which provide a fiber-optic interface to the ONS 15310-MA SDH and can be

provisioned for various line rates.

19. NTP-H162 Preprovision a Card Slot, page 1-32—As needed, complete this procedure to

preprovision an empty card slot with a card that will be installed later.

20. NTP-H163 Remove and Replace a Card, page 1-32—As needed, complete this procedure to remove

and replace an ONS 15310-MA SDH card.

21. NTP-H168 Install the Front Door, page 1-34—As needed, complete this procedure to install the

front door.

22. NTP-H191 Install the Rear Cover, page 1-36—As needed, complete this procedure to install the rear

cover.

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be

accessed only through the use of a special tool, lock and key, or other means of security.

Statement 1017

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Note The ONS 15310-MA SDH is designed to comply with Telcordia GR-1089-CORE Type 2 and Type 4.

Acceptable applications include Central Office Environments (COEs), Electronic Equipment Enclosures

(EEEs), Controlled Environment Vaults (CEVs), huts, and Customer Premise Environments (CPEs).

1-3

Cisco ONS 15310-MA SDH Procedure Guide, R9.0

78-18668-01

Chapter 1 Install the Cisco ONS 15310-MA SDH

Required Tools and Equipment

Note The Cisco ONS 15310-MA SDH is intended for use with telecommunications equipment only.

Warning

The intra-building ports of the ONS15310-MA SDH are suitable only for connecting to intrabuilding or

unexposed wiring or cabling. The intra-building ports of ONS15310-MA SDH MUST NOT be

metallically connected to interfaces that connect to the OSP or its wiring. These interfaces are

designed for use as intra-building interfaces only (Type 2 or Type 4 ports as described in

GR-1089-CORE, Issue 4) and require isolation from the exposed OSP cabling. The addition of Primary

Protectors is not sufficient protection in order to connect these interfaces metallically to OSP wiring.

Required Tools and Equipment

You will need the following tools and equipment to install and test the ONS 15310-MA SDH.

lncluded Materials

These materials are shipped with the ONS 15310-MA SDH. The number in parentheses provides the

quantity of the item included in the package.

•Ground lug (1)

•Screws: panhead, 10-32 x 0.375 (10)

•Screws: panhead, 10-32 x 0.37, green zinc (2)

•Screws: panhead, 12-24 x 0.75 (8)

•Screws: panhead, 10-32 x 0.31 (2)

•Screws: panhead, 8-32 x 0.31 (3)

•Kep nut: 10-32 x 0.170

•Rack mount bracket

•Interconnect plate

•Rack mount bracket for 19-inch rack

•Cable routing bracket

User-Supplied Materials

These materials and tools are required but are not supplied with the ONS 15310-MA SDH.

•Equipment rack (26 inches total width for a 19-inch rack)

•Fuse and alarm panel

•Copper power cable (from fuse and alarm panel to assembly), #12 AWG

•Ground cable, #6 AWG stranded (minimum)

•Alarm In cable, unshielded cable terminated with a DB-37 connector

•Alarm Out cable, shielded cable terminated with a DB-25 connector

1-4

Cisco ONS 15310-MA SDH Procedure Guide, R9.0

78-18668-01

Chapter 1 Install the Cisco ONS 15310-MA SDH

Required Tools and Equipment

•Craft port serial cable, CAT-5 terminated with RJ-45

•BITS timing port cable, CAT-3/CAT-5 terminated with DB-9 connector

•User data channel (UDC) cable: EIA/TIA-232 port cable, CAT-5 terminated with RJ-45

•Management LAN cable, CAT-5 terminated with RJ-45

•Single-mode LC fiber jumpers with UPC polish (55 dB or better) for optical interfaces

•E1 cabling, shielded, terminated to a 21-pair #26AWG cable, with dual 64-pin CHAMP connectors

at far end with separate transmit and receive, straight termination (optional)

•Shielded coaxial cable terminated with BNC connectors for DS-3/E3 ports

•Tie wraps and/or lacing cord

•Labels

Tools Needed

The following tools are needed to complete the procedures in this chapter:

•#2 Phillips screw driver

•Medium slot head screw driver

•Small slot head screw driver

•Wire cutters

•Wire strippers

Test Equipment

The following test equipment is needed to complete the procedures in this chapter:

•Volt meter

•Power meter (for use with fiber optics only)

•Bit error rate (BER) tester, E1 and DS-3/E3

Note In this chapter, the terms “ONS 15310-MA SDH” and “shelf assembly” are used interchangeably. In the

installation context, these terms have the same meaning. Otherwise, shelf assembly refers to the physical

steel enclosure that holds cards and connects power, and ONS 15310-MA SDH refers to the entire

system, both hardware and software.

1-5

Cisco ONS 15310-MA SDH Procedure Guide, R9.0

78-18668-01

Chapter 1 Install the Cisco ONS 15310-MA SDH

Required Tools and Equipment

NTP-H149 Unpack and Inspect the ONS 15310-MA SDH Shelf

Assembly

Step 1 Complete the “DLP-H1 Unpack and Verify the Shelf Assembly” task on page 16-1.

Step 2 Complete the “DLP-H2 Inspect the Shelf Assembly” task on page 16-1.

Step 3 Continue with the “NTP-H150 Install the Shelf Assembly” procedure on page 1-5.

Stop. You have completed this procedure.

NTP-H150 Install the Shelf Assembly

Note The ONS 15310-MA SDH installations are suitable for Network Telecommunication facilities and

locations where NEC are applicable.

Purpose This procedure describes how to unpack the ONS 15310-MA SDH and

verify the contents.

Tools/Equipment None

Prerequisite Procedures None

Required/As Needed Required

Onsite/Remote Onsite

Security Level None

Purpose This procedure describes how to mount ONS 15310-MA SDH shelf

assemblies in a rack.

Tools/Equipment #2 Phillips screwdriver

#12-24 mounting screws (4)

#10-32 ear mounting screws (8)

Universal mounting ears (2)

Dual-assembly plate

19-inch-rack mounting ear

Fuse and alarm panel, if not installed

Prerequisite Procedures NTP-H149 Unpack and Inspect the ONS 15310-MA SDH Shelf Assembly,

page 1-5

Required/As Needed Required

Onsite/Remote Onsite

Security Level None

1-6

Cisco ONS 15310-MA SDH Procedure Guide, R9.0

78-18668-01

Chapter 1 Install the Cisco ONS 15310-MA SDH

Required Tools and Equipment

Warning

To prevent the system from overheating, do not operate it in an area that exceeds the maximum

recommended ambient temperature of 149°F (65°C).

Statement 1047

Warning

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special

precautions to ensure that the system remains stable. The following guidelines are provided to ensure

your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the

heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing

the unit in the rack.

Statement 1006

Step 1 Complete the necessary rack mount task DLP-H248 Mount a Single ONS 15310-MA SDH in a Rack,

page 18-49.

Step 2 Continue with the “NTP-H169 Install the Cable Management Bracket” procedure on page 1-6.

Stop. You have completed this procedure.

NTP-H169 Install the Cable Management Bracket

Warning

The covers are an integral part of the safety design of the product. Do not operate the unit without the

covers installed.

Statement 1077

Step 1 Line up the three screw holes on the rear of the bracket with the screw holes at the bottom of the

ONS 15310-MA SDH shelf assembly (Figure 1-1).

Purpose This procedure describes how to install the cable management bracket,

which is used for routing optical and Ethernet cables.

Tools/Equipment #2 Phillips screwdriver

Standard cable management bracket and

three #8-32 x 0.31 inch (0.79 cm) screws (included with the ship kit)

Extended cable management bracket (15310-CBLMGT) and

five 8-32 x 0.31 inch (0.79 cm) screws

Prerequisite Procedures NTP-H150 Install the Shelf Assembly, page 1-5

Required/As Needed Required

Onsite/Remote Onsite

Security Level None

1-7

Cisco ONS 15310-MA SDH Procedure Guide, R9.0

78-18668-01

Chapter 1 Install the Cisco ONS 15310-MA SDH

Required Tools and Equipment

Figure 1-1 Installing the Standard Cable Management Bracket

Step 2 To secure the bracket to the shelf, use the screwdriver to install three 8-32 x 0.31 inch (0.79 cm) screws,

torqued to 15 to 18 inch-lbs.

Step 3 If you are installing the extended bracket, install two 8-32 x 0.31 inch (0.79 cm) screws, torqued to 15

to 18 inch-lbs, through the top of the bracket directly into the ESD faceplates adjacent to Slots 1 and 6

on either side of shelf (Figure 1-2).

151577

1-8

Cisco ONS 15310-MA SDH Procedure Guide, R9.0

78-18668-01

Chapter 1 Install the Cisco ONS 15310-MA SDH

Required Tools and Equipment

Figure 1-2 Installing the Extended Cable Management Bracket

Step 4 If you plan to install electrical interface assemblies (EIAs), continue with the “NTP-H166 Remove the

Blank Sheet Metal Covers” procedure on page 1-9 to access the backplane. If not, continue with the

“NTP-H151 Install the Power and Ground” procedure on page 1-12.

Stop. You have completed this procedure.

151578

1-9

Cisco ONS 15310-MA SDH Procedure Guide, R9.0

78-18668-01

Chapter 1 Install the Cisco ONS 15310-MA SDH

Required Tools and Equipment

NTP-H166 Remove the Blank Sheet Metal Covers

Warning

The covers are an integral part of the safety design of the product. Do not operate the unit without the

covers installed.

Statement 1077

Step 1 Use a Phillips screwdriver to remove the five screws holding each sheet metal cover in place.

Figure 1-3 shows the screw locations of the sheet metal covers installed on the A-side and B-side of the

ONS 15310-MA SDH.

Figure 1-3 Blank Sheet Metal Covers

Step 2 Store the panels for later use. Attach the backplane cover(s) whenever EIA(s) are not installed.

Purpose This procedure describes how to access the backplane by removing the

blank sheet metal covers. The backplane has two sheet metal covers (one

on either side).

Tools/Equipment #2 Phillips screwdriver

Prerequisite Procedures NTP-H150 Install the Shelf Assembly, page 1-5

Required/As Needed Required

Onsite/Remote Onsite

Security Level None

151576

Blank sheet metal cover

installed on the B Side

Blank sheet metal cover

installed on the A Side

1-10

Cisco ONS 15310-MA SDH Procedure Guide, R9.0

78-18668-01

Chapter 1 Install the Cisco ONS 15310-MA SDH

Required Tools and Equipment

Step 3 If you plan to install electrical interface assemblies (EIAs), continue with the “NTP-H167 Install the

EIAs” procedure on page 1-10. If not, continue with the “NTP-H151 Install the Power and Ground”

procedure on page 1-12.

Stop. You have completed this procedure.

NTP-H167 Install the EIAs

Caution Connect only SELV services to the high-density EIAs on the ONS 15310-MA SDH.

Step 1 Determine which high-density EIA is designed for installation on the B Side and which is designed for

installation on the A Side (Figure 1-4).

Purpose This procedure describes how to install electrical interface assemblies

(EIAs). Refer to the Cisco ONS 15310-MA SDH Reference Manual for

descriptions of the EIAs.

Tools/Equipment #2 Phillips screwdriver

High-density EIA(s)

6-32 x 5/16-inch pan head screws (3, included with EIA)

Prerequisite Procedures NTP-H169 Install the Cable Management Bracket, page 1-6

Required/As Needed As needed

Onsite/Remote Onsite

Security Level None

Other manuals for ONS 15310-MA SDH

Table of contents

Other Cisco Network Hardware manuals

Cisco

Cisco Fourth-Generation Versatile Interface Processor... Operator's manual

Cisco

Cisco NCS 1002 User manual

Cisco

Cisco ONS 15540 ESP Manual

Cisco

Cisco VIP-4R/4T Operating and maintenance instructions

Cisco

Cisco C8510MSR-SKIT-DC - Catalyst 8510 Multiservice Switch... User manual

Cisco

Cisco OL-6109-01 User manual

Cisco

Cisco Nexus 93600CD-GX Manual

Cisco

Cisco GS7000 Operating instructions

Cisco

Cisco Edge Concentrator MGX 8220 Reference manual

Cisco

Cisco Gigabit Switch Router Cisco 12012 User manual

Cisco

Cisco IPS-4260-K9 - IPS Sensor 4260 User manual

Cisco

Cisco Mc3810 - 16MB Flash Memory Quick guide

Cisco

Cisco o UCS X440p Installation and maintenance instructions

Cisco

Cisco TelePresence Service manual

Cisco

Cisco Meraki MX65W User manual

Cisco

Cisco Secure Network Server 3700 Series Manual

Cisco

Cisco PC4000 User manual

Cisco

Cisco CE-507 - Content Engine 507 User manual

Cisco

Cisco GS7000 Operating instructions

Cisco

Cisco NSS2000 - Gigabit Storage System Chassis How to use

Cisco

Cisco Remote PHY Shelf 7200 Installation manual

Cisco

Cisco S170 Web User manual

Cisco

Cisco Content Delivery Engine 100/200/300/400 Manual

Cisco

Cisco ATM Cable Interface Processor ACIP-SM(=) Operator's manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide