Cisco 7821 User manual

Home

PBXware

SERVERware

TELCOware

SIPmon

SIPProt

Desktop & Mobile

UADs

Appliances

From Bicom Systems Wiki

Contents

1 Cisco 7821 User Guide

■

2 Requirements

■

3 Installation

■

3.1 Power Adapter

■

3.2 IP Address

■

3.3 Factory Settings

■

4 Registering Device

■

4.1 Manual Configuration

■

4.2 Auto Provisioning

■

Cisco 7821 User Guide

This User Guide is written as general guide on how to set up the Cisco 7821 to work with

PBXware.

Requirements

1. Identify Cisco 7821 device

To start and successfully complete registration of your Cisco device you need to know which

■

device model you will setup.

From the back of each Cisco device there are exact model information that you should check.

■

Although different device models can have exactly the same requirements and installation

procedure, device models can also have significantly different requirements and installation

procedure, so that ignorance of your own model may result in the inability to successfully set

up your device.

2. device firmware

Make sure that your device is loaded with appropriate firmware version, 11.0.1.

■

For Cisco 7821 press settings button, then type 61 to check the version of the software.

■

3. DHCP server

Fully configured and operational DHCP server.

■

4. PBXware version

In order to find out the PBXware version, please login to PBXware and navigate to Settings:

■

About. On the top of "About" page is a code similar to this one "PBXware Edition: Business,

Release: 4.1.3 (041373f), Running: 1.4.24-gc-75ee203", where "Release" denotes the exact

version of your PBXware.

Installation

This chapter describes how to install and connect the device to the electrical power and data

network as well as how to apply factory settings.

The following topics are covered:

- Power adapter

- Factory Settings

Power Adapter

1. Connect the Network and Power

Connect the DC plug on the power adapter to the DC port on the device and connect the other

■

end of the power adapter into an electrical power outlet.

Connect the ethernet cable between the Internet port on the device and the network port on a

■

router or switch to access LAN.

IP Address

1. Find out your Cisco 7821 IP Address

For Cisco 7821, press settings button then type 62 to check ip address of the phone.

■

Factory Settings

1. Reset to factory settings

This step is not required for out-of-the-box devices, however, if the device has been already used

then it is a must.

For Cisco 7821, press settings button then type 55. Confirm with OK on prompt to factory

■

reset the phone.

Wait sometime prior for device to reboot.

■

NOTE: Do not unplug or remove power to the device while it is updating firmware and

configurations.

Registering Device

This chapter describes how to identify Cisco 7821 phone model, requirements that must be met

and how to register the device using manual configuration or auto provisioning.

The following topics are covered:

- Manual Configuration

- Auto Provisioning

Manual Configuration

This chapter describes how to set UAD settings, create PBXware extension and register the

device.

The following topics are covered:

- UAD Settings

- Creating Extension

- Registering Device

UAD Settings

1. Login to PBXware web administration interface

Open a new browser window and enter the IP address in order to access the PBXware web

■

administration login screen. Example: http://192.168.1.10

■

2. UAD settings

Navigate to Settings:UAD.

■

Make sure Cisco 7821 UAD is enabled. To check the UAD status click on the edit icon

■

corresponding to your Cisco phone.

Make sure Status is set to Active, Auto provisioning is set to No, and DHCP is set to Yes.

■

UAD settings

Click on the Save button to save changes.

■

Creating Extension

1. Add Extension

Navigate to Extensions. Click on Add Extension.

■

The standard options window will be shown below.

■

Select Cisco 7821 phone model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all extensions registered on the LAN and Remote is for all extensions

registered from remote networks, WAN, Internet etc.

Click on the Next step button.

■

2. Extension values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this extension. This e-mail address will receive all

system notification messages. Example: [email protected]

Creating Extension

Click on the Save button.

■

Optionally, click on the Save & E-mail button. Account details will be sent to the e-mail

■

address associated with this extension.

OPTIONAL FIELDS

Extension

■

An auto-generated extension number based on the next available sequential number. An

extension value can be changed. Example: 1003.

Secret

■

A secret value associated with the UAD is auto-generated in order to allow the UAD to

successfully register with the system. The secret value can be changed, however it is

STRONGLY recommended not to change the system generated value to a simple value like

"1234" or "1003" etc.

■

An auto-generated PIN will allow access to voicemail and online self-care.

Registering Phone

This chapter describes how to register Cisco 7821 device using Hostname or IP Address.

Hostname or IP Address

1. Login to device web administration interface

Open a new browser window and enter your phone IP address in order to access the device

■

web administration interface login screen. Example: http://192.168.1.22.

Click on Admin Login in the top right corner of the administration interface.

■

Click on Advanced in the top right corner of the administration interface.

■

Click on Voice on the main menu.

■

Click on Ext 1 on the sub menu.

■

Enter or set the following details into the respective fields.

■

REQUIRED FIELDS:

Proxy (Proxy and Registration section)

■

Enter the Hostname or IP Address of the PBXware.

- Example for Hostname: voip.bicomsystems.com

- Example for IP Address: 192.168.1.10

User ID (Subscriber Information section)

■

PBXware extension number. Example: 1003.

Password

■

The Secret of the extension as received in the e-mail associated with this extension.

Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created

extension.

Navigate down to "Dial Plan" section. Clear the Dial Plan field, then copy and paste the

■

following value.

(*x.|**x.|*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxx|xxxxxxxxxxxx.)

Click on the Submit button.

■

You'll have to wait sometime prior for the device to reboot. If everything is done as above

■

described, you should have successfully registered your device to PBXware.

Auto Provisioning

This chapter describes how to set UAD settings, create PBXware extension and register the

device using DHCP or Static IP address.

The following topics are covered:

- UAD Settings

- Creating Extension

- Registering Device

UAD Settings

1. Login to PBXware web administration interface

Open a new browser window and enter the IP address in order to access the PBXware web

■

administration login screen. Example: http://192.168.1.10.

■

2. UAD settings

Navigate to Settings:UAD.

■

Make sure Cisco 7821 UAD is enabled. To check the UAD status click on the edit icon

■

corresponding to your Cisco phone.

Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes.

■

UAD settings

Click on the Save button to save changes.

■

Creating Extension

1. Add Extension

Navigate to Extensions. Click on Add Extension.

■

The standard options window will be shown below.

■

Select Cisco 7821 device model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all extensions registered on the LAN and Remote is for all extensions

registered from remote networks, WAN, Internet etc.

Click on the Next step button.

■

2. Extension values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this extension. This e-mail address will receive all

system notification messages. Example: [email protected]

Auto Provisioning

■

Set to Yes.

MAC Address

■

Enter Cisco 7821 device MAC address. Example: 0002FDFF1536. MAC address can be

found at the back of the phone.

Creating Extension

Click on the Save button.

■

Registering Phone

This chapter describes how to register Cisco 7821 device using DHCP, TFTP or HTTP.

The following topics are covered:

- DHCP

- TFTP or HTTP

DHCP

1. Configure DHCP

Make sure your DHCP router is configured to use option 66 to automatically instruct devices

■

with the URL for auto provisioning. For more information refer to your router documentation

or contact your network administrator.

2. Device first boot or user initiated reboot

Auto provisioning process will start during device first boot or after reboot process has been

initiated by user. DHCP server will instruct the device where from to pickup appropriate

configuration file. If everything is done as above described, you should have successfully

registered your device to PBXware.

TFTP or HTTP

1. Login to device web administration interface

Open a new browser window and enter your device IP address in order to access the device

■

web administration interface login screen. Example: http://192.168.1.22

Click on Admin Login in the top right corner of the administration interface.

■

Click on Advanced in the top right corner of the administration interface.

■

Click on Voice at the top navigation menu.

■

Click on Provisioning sub menu.

■

You can use TFTP or HTTP protocols in order to Auto Provision your Cisco SPA device.

■

Choose which protocol you want to use:

■

- TFTP

- HTTP

TFTP

In the Profile Rule field enter tftp:// followed by Hostname or IP Address, followed then by

■

/$MA.cfg.

- Example for Hostname: tftp://voip.bicomsystems.com/$MA.cfg

- Example for IP Address: tftp://10.1.70.150/$MA.cfg

Click on Submit and wait 35 seconds. The phone may reboot.

■

Auto provisioning process will start during device reboot process, device will pickup

■

appropriate configuration file from PBXware. If everything is done as above described, you

should have successfully registered your device to PBXware.

HTTP

This chapter describes how to use HTTP protocol in order to register Cisco SPA device. NOTE:

Your PBXware needs to be configured correctly for HTTP to work. Please make sure that HTTP

username and HTTP passwords are set in Auto provisioning section in Settings ->

Servers/Tenants -> Server/Tenant name [edit]. Contact your PBXware administrator. Bicom

Systems can provide service to set up this for you.

In the Profile Rule field enter:

■

- Example for Hostname using HTTP: [--uid http-username --pwd

http-password]http://voip.bicomsystems.com/prov/$MA.cfg

- Example for IP Address using HTTP: [--uid http-username --pwd

http-password]http://10.1.70.150/prov/$MA.cfg

Make sure you replace Hostname or IP Address from this example with your PBXware

■

Hostname or IP address.

Make sure to replace http-username and http-password with Your server http username

■

and password.

Click on Submit and wait 35 seconds. The phone may reboot.

■

Auto provisioning process will start during phone reboot process, phone will pickup

■

appropriate configuration file from PBXware. If everything is done as above described, you

should have successfully registered your phone to PBXware.

Retrieved from "http://wiki.bicomsystems.com/Cisco_7821"

Disclaimers - About Bicom Systems Wiki

Other manuals for 7821

Table of contents

Other Cisco IP Phone manuals

Cisco

Cisco MCS 7800 Series Specification sheet

Cisco

Cisco DATAVOX 7941 User manual

Cisco

Cisco UNIFIED 9971 User manual

Cisco

Cisco 7925G - Unified Wireless IP Phone VoIP Quick reference guide

Cisco

Cisco Unified 7912G User manual

Cisco

Cisco 7940/7960 User manual

Cisco

Cisco 7940G User manual

Cisco

Cisco Unified 8961 User manual

Cisco

Cisco 9951 Video User manual

Cisco

Cisco SPA 303 Series User manual

Cisco

Cisco 7841 User manual

Cisco

Cisco 8945 User manual

Cisco

Cisco 7962G - Unified IP Phone VoIP User manual

Cisco

Cisco SPA92X User manual

Cisco

Cisco 8945 User manual

Cisco

Cisco 8945G User manual

Cisco

Cisco 7920 - Unified Wireless IP Phone VoIP User manual

Cisco

Cisco SPA300 Series User manual

Cisco

Cisco 8811 User manual

Cisco

Cisco 8941 User manual

Cisco

Cisco 6800 Series User manual

Cisco

Cisco Small Business Pro SPA 508G User manual

Cisco

Cisco IP Phone 8851 User manual

Cisco

Cisco SPA 303 Series User manual

Popular IP Phone manuals by other brands

Alcatel

Alcatel 4028 manual

Polycom

Polycom Polycom VVX 600 quick reference

Polycom

Polycom SoundPoint IP 450 datasheet

Polycom

Polycom SoundPoint IP 650 user guide

Proximus

Proximus Maestro 3016 IP quick start guide

Fanvil

Fanvil X4 user manual

Snom

Snom 320 quick start guide

Yealink

Yealink Yealink SIP-T46G Guide

Avaya

Avaya 4625SW user guide

Yealink

Yealink SIP-T52S quick start guide

Nortel

Nortel 1140E Getting started

Nexotek

Nexotek NT-P500 user manual

Avaya

Avaya Integral 5 R3.0 user guide

GE 28320EE2 - Dect 6.0 InfoLink 2 user guide

Avaya

Avaya 4600 Series Administrator's guide

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP user guide

Nortel

Nortel i2050 installation guide

Fiberme

Fiberme FAP260 Series user guide