Char-Griller 5050 User manual
OM5050E.2 ™ & © Char-Griller / A&J Mfg. 10
Step 1
Attach the LEFT LEGS & RIGHT LEGS to the BASE using four (4) ½” BOLTS and four
(4) ¼” LOCK WASHERS as shown. When you install the LEFT LEG & RIGHT LEG,
please make sure that the holes at the top of the LEGS are facing out. Please note
that the wheel legs have inside and outside sides. The axel will not fit through the
legs if the outside of the leg is not facing out
Step 2
Attach the LEG CROSSBAR to the frame as shown making sure that the holes on the
CROSSBAR are facing inward. See below.
OM5050E.2 ™ & © Char-Griller / A&J Mfg. 11
Step 4
Install the LEG BRACES to the LEGS using eight (8) LOCK WASHERS and eight (8)
½” BOLTS as shown. Remember to NOT tighten the bolts until completing
step 6.
Step 3
Attach BOTTOM SHELF to the LEGS (as shown below).
OM5050E.2 ™ & © Char-Griller / A&J Mfg. 12
Step 6
Attach the GAS GRILL BODY and CHARCOAL GRILL BODY to the LEG CROSSBAR us-
ing eight (8) ½” BOLTS, eight (8) LOCK WASHERS and eight (8) FLAT WASHERS in
order shown. Make sure to insert the bolt first through the lock washer then the flat
washer then through the grill body as shown.
12
4334
12
Turn grill assembly up on end as shown and tighten
ALL nuts and bolts.
Step 5
Install one WASHER, COTTER PIN and HUB CAP onto the AXLE then slide the AXLE
through WHEELS and legs as shown. Finish by attaching 2nd WASHER, COTTER PIN
and HUB CAP.
Axle
Wheel
Washer
Cotter Pin
Hub Cap
OM5050E.2 ™ & © Char-Griller / A&J Mfg. 13
Step 7
Attach (2)SLIDER BRACKETS and (1)STOPPER BRACKET to Bottom of GRILL BODY as
shown on Figure 2 and Figure 3 using (6) #10-24 x 0.40” bolts. NOTE: Oriented
Brackets as shown in Figure 1. Install CATCH PAN by placing CATCH PAN support
brackets on top of SLIDER BRACKETS underneath GRILL BODY, see Figure 4, and
then slide it forward until you can hang the CATCH PAN side bracket onto the STOP-
PER BRACKET. From the rear of the grill, slide the GREASE TRAY into the guides/
rails under the CATCH PAN.
CATCH PAN
Support Bracket
CATCH PAN
CATCH PAN
Side Bracket
Stopper Bracket
Figure 4
(6)#10-24 x
0.40” Bolt (2) Slider Bracket (1) Stopper Bracket
Slider Bracket
Stopper Bracket
Figure 1
#10-24 x 0.40” Bolt
Slider Bracket
Figure 2 Figure 3
GRILL BODY
Slider Bracket
OM5050E.2 ™ & © Char-Griller / A&J Mfg. 14
Note: the hose should
be on the outside of
the leg brace.
Side Burner
Venturi Tube
Step 8
Install the SIDE BURNER and the CONTROL PANEL to the GRILL BODY with eight (8)
½” BOLTS and eight (8) LOCK WASHERS. Make sure the SIDE BURNER VALVE tip is
completely inside of the SIDE BURNER VENTURI TUBE see figure below. (NOTE: Hose
should be on the outside of the leg brace). Then tighten all the bolts. Slide GREASE
TRAY onto the rail underneath CATCH PAN. Slide the other GREASE TRAY onto the rail
underneath the SIDE BURNER PAN.
Side Burner Valve
Leg Brace
Hose
GREASE
TRAY
GREASE
TRAY
Note: the hose should
be on the outside of
the leg brace.
Side Burner
Venturi Tube
Step 8
Install the SIDE BURNER and the CONTROL PANEL to the GRILL BODY with eight (8)
½” BOLTS and eight (8) LOCK WASHERS. Make sure the SIDE BURNER VALVE tip is
completely inside of the SIDE BURNER VENTURI TUBE see figure below. (NOTE: Hose
should be on the outside of the leg brace). Then tighten all the bolts. Slide GREASE
TRAY onto the rail underneath CATCH PAN. Slide the other GREASE TRAY onto the rail
underneath the SIDE BURNER PAN.
Side Burner Valve
Leg Brace
Hose
GREASE
TRAY
GREASE
TRAY
Note: the hose should
be on the outside of
the leg brace.
Side Burner
Venturi Tube
Step 8
Install the SIDE BURNER and the CONTROL PANEL to the GRILL BODY with eight (8)
½” BOLTS and eight (8) LOCK WASHERS. Make sure the SIDE BURNER VALVE tip is
completely inside of the SIDE BURNER VENTURI TUBE see figure below. (NOTE: Hose
should be on the outside of the leg brace). Then tighten all the bolts. Slide GREASE
TRAY onto the rail underneath CATCH PAN. Slide the other GREASE TRAY onto the rail
underneath the SIDE BURNER PAN.
Side Burner Valve
Leg Brace
Hose
GREASE
TRAY
GREASE
TRAY
OM5050E.2 ™ & © Char-Griller / A&J Mfg. 15
Step 10
Insert the IGNITER WIRES, which are attached to the underside of each BURNER,
through the same hole in the GRILL BODY that the BURNER goes through and then
attach the WIRE to the backside of the ELECTRONIC IGNITER, which is attached to
the back side of the CONTROL PANEL. Any wire can go into any of the three sockets
on the Electronic Igniter.
Burner
Igniter Wire
Electronic Igniter
Step 9
Install the MAIN BURNERS into the GRILL BODY by first inserting the open end of
the BURNERS through the holes in the front of the grill body. Making sure the VALVE
tips are inside the burner tubes. The BURNER with the longest wire is installed on
the right side of the GAS GRILL BODY. Secure the BURNER to the GAS GRILL BODY
with the SCREWS provided.
Valve
Burner
OM5050E.2 ™ & © Char-Griller / A&J Mfg. 16
Step 11
Install the CONDIMENT BASKET to the CHARCOAL GRILL BODY using four (4) LOCK
WASHERS and four (4) ½” BOLTS. From inside the GRILL BODY the BOLTS go
through a LOCK WASHER and then through the GRILL BODY and then screw into the
CONDIMENT BASKET.
Condiment Basket
Bolts and Lock Washers
Step 12
Install the SIDE DAMPER to the CHARCOAL GRILL BODY using one (1) ½” BOLT. The
BOLT should first go through a FLAT WASHER then the DAMPER then the GRILL
BODY then another FLAT WASHER then a LOCK WASHER and then secured with a
HEX NUT. See below.
OM5050E.2 ™ & © Char-Griller / A&J Mfg. 17
Step 13
Attach the SIDE HANDLE to the right side of the CHARCOAL GRILL BODY using two
(2) ½” BOLTS and two (2) LOCK WASHERS as shown. From inside the GRILL BODY
insert each BOLT through a LOCK WASHER and then through the GRILL BODY and
then screw into the SIDE HANDLE. See below.
Lock Washer
Step 14
Attach the HOOD HANDLES to the GRILL HOODS with four (4) LOCK WASHERS and
four (4) WING NUTS as shown below.
Lock Washer
OM5050E.2 ™ & © Char-Griller / A&J Mfg. 18
Step 15
Install the GAS CHIMNEY to the GAS GRILL HOOD and the CHARCOAL CHIMNEY to
the CHARCOAL GRILL HOOD. Insert the CHIMNEYS through each hole from inside
the HOOD and secure with two (2) HEX NUTS and two (2) ½” BOLTS for each CHIM-
NEY, see below.
Step 16
Insert the THERMOMETERS through BEZEL into the GRILL HOODS and secure with
two (2) WING NUTS as shown.
OM5050E.2 ™ & © Char-Griller / A&J Mfg. 19
Step 17
Attach HOODS to the GRILL BODIES using HINGE PINS as shown. Have your helper
stand behind the grill to hold the HOODS in place and keep them from falling. First
place the GAS HOOD onto the GRILL BODY in the closed position then screw the left
HINGE PIN into place. Then place the Charcoal HOOD in place and screw in the right
HINGE PIN. Carefully and slightly open the Charcoal HOOD and insert the center
HINGE PIN from inside the charcoal grill through the HOOD then through the Gas
HOOD and Body as shown. Then insert COTTER PINS through the holes in the three
HINGE PINS.
Hinge Pin
Other manuals for 5050
1
Table of contents
Other Char-Griller Grill manuals
Char-Griller
Char-Griller Smokin' Pro 1224 User manual
Char-Griller
Char-Griller 2121 User manual
Char-Griller
Char-Griller Side Fire Box #2424 User manual
Char-Griller
Char-Griller Table Top 2-2424 User manual
Char-Griller
Char-Griller 789792090207 User manual
Char-Griller
Char-Griller 2828 User manual
Char-Griller
Char-Griller Wood Fire Pro Pellet Grill 9040 User manual
Char-Griller
Char-Griller Flavor Pro 7400 User manual
Char-Griller
Char-Griller 2123 User manual
Char-Griller
Char-Griller Patio Pro 1515 User manual
Char-Griller
Char-Griller BLAZER 2130 User manual
Char-Griller
Char-Griller Patio Pro 1515 User manual
Char-Griller
Char-Griller AKORN 6520 User manual
Char-Griller
Char-Griller Classis 2175 User manual
Char-Griller
Char-Griller 2123 User manual
Char-Griller
Char-Griller Outlaw Grills MAVERICK 1016 User manual
Char-Griller
Char-Griller 789792021218 User manual
Char-Griller
Char-Griller Akorn JR. Kamado 06614 User manual
Char-Griller
Char-Griller Smokin Pro 1244 User manual
Char-Griller
Char-Griller Grillin' Pro 3001 User manual
Popular Grill manuals by other brands
Kenmore
Kenmore 415.16123800 Use and care guide
Camp Chef
Camp Chef PG24CLAU Warning & instruction booklet
Tucker Barbecues
Tucker Barbecues GTR Series Assembly, installation and operating instructions
Monogram
Monogram ZGG540NCP1SS owner's manual
Equipex
Equipex Sodir Savoy Operation manual
Gaggenau
Gaggenau VR 414 610 use and care manual
