CAS HDI User manual

CONTENTS

PRECAUTIONS............................................. 4

PREFACE ....................................................... 6

INSTALLATION & CONNECTION ........... 6

CALIBRATION ............................................. 7

OPERATIONS................................................ 9

1. General Weighing ...................................... 10

2. Weighing with Tare .................................... 10

3. Counting Mode...........................................

4. Weight Comparison Function(HI/OK/LOW) . 12

5. Print Out .................................................. 14

6. Battery Charge .......................................... 15

7. Set-up Mode .............................................. 15

8. User Mode ................................................ 16

ERROR MESSAGES .................................. 17

SERIAL INTERFACE ................................. 17

SPECIFICATIONS ...................................... 18

PRECAUTIONS

PREFACE

Thank you for the purchasing of CAS HDI Indicator.

This Indicator has been designed with CAS reliability, under rigid quality control

and with outstanding performance. Your specialty departments can enjoy with

CAS products.

We hope that CAS product meets your needs.

The user manual is designed to guide you to understand product operation and

proper care of product.

INSTALLATION & CONNECTION

Load cell connection

Connect load cell connector to load cell port which is in the backside of the indicator.

* Connecting method

COLOR

1 (EXC+) RED

2 (EXC-) WHITE

3 (SIG+) GREEN

4 (SIG-) BLUE

5 (SHIELD) SHIELD

Note. Wire color can be different depending on the

loadcell’s manufacturer or it’s model.

* Load cell output to Resolution

V impression to loadcell

Max. load cell output Recommended resolution

4 mV 1/4,000

8 mV 1/8,000

10 mV 1/10,000

CALIBRATION

- Product initialization

Press key to go to Power on

When numbers on the display appears press CAL S/W.

There will be a beeping sound as the product initializes.

- General Calibration

* If the product initiation process is skipped, the #4 value will automatically be set to the

previously set value and the setup process will be skipped.

1. Pressing and holding calibration switch press key to go to calibration mode.

2. Pressing and holding key press key to go to calibration mode.

key : Quick value settings. “1/2/5/10/20/50/DUAL”

Select

4. key : Set-point digits

“00000/0000.0/000.00/00.000/0.0000/0.00000”

Select

5. key : Full Capa. Setting (Input values are converted to grams

*When the quick value setting is Dual “ 3060 : 30-60kg , 6015: 60-150kg , 1530: 150-300kg”

Select

Calibration mode

Zero Calibration (Check that the scale reads zero)

Span Calibration Input value. Note: Input values in Kg.

Place the previously inputted amount of weight on the scale and then

press Select

Calibration complete

OPERATIONS

DISPLAY AND KEYBOARD

KEY FUNCTIONS

KEYS DESCRIPTIONS

Used to set the zero point to 0.00.

Used as an ESC key in Setup Mode.

Used to enter a tare weight and used to cancel a tare weight.

Used to convert the mode as below.

[kg]  [pcs]  [%] [WEIGHT LIMIT ON/OFF] 

[COUNT LIMIT ON/OFF]  [kg]

Used as an ENTER key.

Used to calculate a unit weight of a sample..

[ ] Used to enter next digit.▶

Used to display average weight.

[ ] Used to have number up.

PRINT key.

[▼] Used to have number down.

Used to turn ON or OFF the power.

1. General Weighing

■ The display indicates if the scale is at zero or if there is a tare entered into the

scale by way of a ZERO and NET.

① Turn on the power.

The display shows 0.00.

Make sure that STABLE and

ZERO lamps are on.

When the display is ②not zero

though there is nothing on

the platter, press the ZERO

key.

③Place an item on the platter.

When the STABLE lamp is

on, read the weight.

2. Weighing with Tare

■ Tare is the weight of container being used for a commodity.

The TARE key subtracts the weight of the container.

① Place the container on the

platter.

②Press the TARE key, NET

lamp is on.

③Place an item in the

container.

④ To release the TARE function, remove an item and

container from the platter and press the TARE key.

3. Counting Mode

■ Samples on the platter.

① Press the MODE key until

the display shows “WL OFF”.

If you have set sample size

before the display shows “0”.

②Press the SAMPLE key,

then the display shows “10”.

③If you want to increase

sample size, press the

SAMPLE key. The display

shows 10, 20, 50, 100, 200

every time pressing the

SAMPLE key.

If you set sample size to 10, place 10 samples on the platter. ④

⑤ Press the SET key. The display shows unit weight and then shows the number of samples. If the

display shows “LACK”

* The small value that can escape from ‘LACK’ message is over MAX CAPA / 3000.

a. unit weight ≤ 0.8 e *

b. weight load ≤ 2% of maximum weighing capacity.

⑥Place parts on the platter, then the display shows the number

of parts. You can also use tare function in counting mode.

Table of contents

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

IFM Electronic

IFM Electronic Efector 250 Series Brief instructions

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual