Carrier HYPERSTAT User manual

For more information, contact your local Carrier Controls Expert

INTRODUCTION

HyperStat is a wall-mount thermostat. Its thoughtful design ensures that it blends into most

commercial spaces while still giving a fresh and contemporary feel compared to dated

building control interfaces.

PACKAGE CONTENTS

•HyperStat device

•Mounting accessories

SPECIFICATIONS

Power

Power Source: 24V AC/DC input (+/- 15%)

Peak consumption: 1.4VA Maximum

Operating range

Temperature 32 to 122°F (0°C to 50°C)

Humidity 20-85% non-condensing.

Communication

Sensor bus for daisy chained sensor communication and low power 3V dc.

4-wire interface for RS 485 communication @ 115200 baud and 5V

DC, 100mA power source

900-928 MHz Mesh IEEE 802.15.4-compliant, for communications to CCU

Bluetooth: BLE 4.1 for commissioning, and communication to wireless sensors

Onboard Sensors

Temperature range of 32 to 122°F with an accuracy of +/-1°F

Humidity 0 to 100% with an accuracy of 2%

CO2 sensor with a range of 0 - 40,000 ppm, accuracy of +/-30ppm

VOC sensor; Typical Accuracy: 15% of measured value; TVOC: 0 - 60,000

ppb;

Occupancy sensor based on passive infrared (PIR) with adetection range of

4m with a 15-degree angle

Light Sensor. Ambient light sensor • <100 LUX resolution • High-accuracy UV

index sensor • Matches erythermal curve

Sound sensor with 40-120dB response for 100Hz to 10KHz

PM2.5, PM10 sensor (optional). Detection range of 0-1000µg/m3 and accuracy

of +/-10µg/m3 (PM2.5, 0-100µg/m3) or +/-25µg/m3 (PM10, 0-

100µg/m3). Maximum long-term mass concentration precision limit drift:

•0 to 100 µg/m3 ±1.25 µg/m3/year

•100 to 1000 µg/m3 ±1.25 % mV/year

Inputs

2 x 10K Type-2 thermistor inputs with 2% accuracy

2 x 0-10V Analog voltage inputs with 2% detection accuracy (2-10V)

Touch slider for temperature control along with 3 mechanical buttons

HYPERSTAT

(7C-HS-C2W-X)

INSTALLATION GUIDE

Scan this QR

code to get a

more detailed

version of the

Installation

Guide

For more information, contact your local Carrier Controls Expert

Outputs

6 x Relays rated for 24V DC/1A

3 x 0-10V or 4-20mA analog outputs

2.8" 240x320 pixel TFT display

PRECAUTIONS

•Failure to wire devices with correct polarity when using a shared transformer,

may result in damage to any device powered.

•Never connect or disconnect the wiring with the power ON.

•Do not allow the powered wires to touch the circuit boards.

•Always install complying with all state and local codes.

•Do not assemble the front to the back plate while it is powered on.

•Once Installed the HyperStat takes seven days to auto-calibrate and settles at a

steady state value.

•Avoid mechanical stress on the CO2 sensor to get accurate readings.

MOUNTING

1. HyperStat Interface - Conventional

5. Rubber cover 2

2. HyperStat Main 6. Gang Box

3. Allen head screws

7. PHP screws

4. Rubber cover 1 8. Backplate

For more information, contact your local Carrier Controls Expert

1. HyperStat Interface - Conventional

5. Rubber cover 2

2. HyperStat Main 6. Gang Box

3. Allen head screws

7. PHP screws

4. Rubber cover 1 8. External Antenna

1. Place the HyperStat Interface-Conventional and the back plate (only if the gang box is

fixed vertically) on the gang box such that the back plate covers the gang box and fix

these two items to the wall gang box with the PHP screws provided in the box.

2. Now align the HyperStat main to lock onto the HyperStat Interface-Conventional.

3. Use the Allen head screws to make this entire setup tamper-proof.

4. Rubber covers 1 and 2 must be fixed to cover the programming pins.

5. Connect the antenna to the device as shown in the above figure. Rotate the antenna

clockwise to lock it in place.

DIS-ASSEMBLING

1. If the HyperStat is mounted on the wall, hold the front plastic with both hands and pull it

away from the wall.

2. If you are holding the HyperStat in your hands, insert a flat head screwdriver in the notch

provided (marked by the two arrows shown in the image) between the front and back

plastic and twist to separate them.

For more information, contact your local Carrier Controls Expert

Note

•Favorable for Pollution degree 2 or the equivalent •Rated impulse voltage – 330V

•Type action – Type 1. C •Operating Ambient Temperature:

0°C to 50 °C

•The method of connection/disconnection for screwless

terminals is mentioned in the article pointed by the QR

label on the box.

•Indoor Use Only

•Terminal Identification – In the Operating Manual •Powered by Class 2 Power Source

CARRIER CLIMAVISION TECHNICAL SUPPORT

Installation and servicing of Control Systems can be hazardous due to electrical

components. Only trained and qualified service personnel should install, repair or service

control system components.

For more information on wiring, commissioning, or usage of the ClimaVision product line,

please refer to any documentation provided with the job. If no documentation was provided

with the job, please use the ClimaVision Help Center (support.climavision.com) where you

can find application specific wiring schematics and helpful user guides and videos or scan

the QR code here:

If you need help beyond that, please reach out to your local Carrier distributor for support.

Scan this QR code to

get a more detailed

version of the

Installation Guide

This manual suits for next models

Other Carrier Thermostat manuals

Carrier

Carrier TSTATCCPF101 User manual

Carrier

Carrier Thermostat Assembly instructions

Carrier

Carrier TST-EEPC06111SCS00 User manual

Carrier

Carrier PROGRAMMABLE THERMOSTAT Assembly instructions

Carrier

Carrier SUI User manual

Carrier

Carrier 33CS400-01 User manual

Carrier

Carrier TSTAT Operation manual

Carrier

Carrier TP-PHP01-A User manual

Carrier

Carrier Performance TP-NHP User manual

Carrier

Carrier PTACSTAT-NP-HP Installation instructions

Carrier

Carrier 53DFST2-NP User manual

Carrier

Carrier Comfort Touch-n-Go User manual

Carrier

Carrier Touch-n-Go TC-PHP01-A User manual

Carrier

Carrier 53DFS250-SL User manual

Carrier

Carrier AQUAZONE 50QE900 User manual

Carrier

Carrier Comfort Pro 33CSCNACHP-01 User manual

Carrier

Carrier Comfort Touch-n-Go User manual

Carrier

Carrier TC-NAC User manual

Carrier

Carrier 33CS220-LA User manual

Carrier

Carrier 33CS420-01 User manual

Carrier

Carrier 50QE900-511WS User manual

Carrier

Carrier CRC2 - NTC User manual

Carrier

Carrier debonair 33cssn2-wc User manual

Carrier

Carrier Connect 33CONNECTSTAT43 User manual

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide

Honeywell

Honeywell T6811 quick guide