Carrier A07049 User manual

T P --- PA C , T P --- P H P

T P --- N A C , T P --- N H P

PerformancetSeries

AC / HP Thermostat

Installation Instructions

A07049 A07048

Programmable Control Non---Programmable Control

NOTE: Read the entire instruction manual before starting the installation.

TABLE OF CONTENTS

PAGE

SAFETY CONSIDERATIONS 2....................................

INTRODUCTION 3..............................................

INSTALLATION CONSIDERATIONS 4..............................

INSTALLATION 7...............................................

SYSTEM START--UP AND CHECKOUT 36..........................

OPERATIONAL INFORMATION 39................................

TROUBLESHOOTING 43.........................................

WIRING DIAGRAMS 45..........................................

THERMOSTAT CONFIGURATION RECORD 54......................

SAFETY CONSIDERATIONS

Read and follow manufacturer instructions carefully. Follow all local electrical

codes during installation. All wiring must conform to local and national electrical

codes. Improper wiring or installation may damage AC/HP Control.

Recognize safety information. This is the safety--alert symbol . When you see

this symbol on the equipment and in the instruction manual, be alert to the

potential for personal injury.

Understand the signal words DANGER,WARNING,andCAUTION.These

words are used with the safety--alert symbol. DANGER identifies the most

serious hazards which will result in severe personal injury or death. WARNING

signifies a hazard which could result in personal injury or death. CAUTION is

used to identify unsafe practices which may result in minor personal injury or

product and property damage. NOTE is used to highlight suggestions which will

result in enhanced installation, reliability, or operation.

INTRODUCTION

Carrier’s 7--day, 5/2--day, 1--day programmable and non--programmable

Performance Series Thermostat Control is a wall--mounted, low--voltage control

which combines temperature and humidity control in either a single unit or a

two--piece unit. In two--piece configuration, the relays are located near the

equipment and a two--wire connection is used between the Display Module and

the Equipment Control Module. Single--piece installation requires more wiring

and results in a higher profile. The EdgetThermostat has no need for batteries

to store user--configured settings in memory. During power loss its internal

memory saves settings for unlimited time, and the clock continues to run for at

least 24 hours. An extension of Carrier’s proven line of thermostats; it provides

separate setpoints for heating and cooling in addition to humidification and

dehumidification.

In the Edge Thermostat Control’s programmable configuration, different heating

and cooling setpoints and times are programmable for 4 periods per day or 2

periods per day. Programming can be done for 7 days per week, 5/2 days per

week, or 1 day. The programmable Thermostat Control can also be user

configured as a non--programmable Thermostat Control. When operating as

non--programmable, the Edge Thermostat Control will still have both

temperature and humidity control.

The non--programmable Thermostat Control features Touch ’N’ Gotsettings

for quick and easy temperature change without complicated programming

schedules. The non--programmable Edge Thermostat Control will still have both

temperature and humidity control. And, its Touch ’N’ Go technology enables the

user to switch between three different user--configurable settings through

intuitive buttons located just below the display.

INSTALLATION CONSIDERATIONS

Power

This control is powered by 24VAC only. It requires 24VAC (Rh and/or Rc and C

terminals) of the low--voltage transformer to be connected to it for proper

operation. It will not operate without these 2 connections. Rh and Rc are

connected via PCB breakout jumper. See Fig. 1. For applications using two

24VAC transformers, one in the indoor unit and one in the outdoor unit, connect

the common from each to the C terminal. Connect R from the indoor unit to the

Rh terminal. Connect R from the outdoor unit to the Rc terminal. Then, break

jumper on the circuit board. The W and HUM signals are taken from the Rh

power and the G signal is taken from the Rc power. If Thermidistat Control has

been installed in a two--transformer application that is later changed to a

single--transformer installation, installer must install a field supplied jumper

between Rc and Rh. Depending on the installation, up to 14 wires may be

required. Installation as two--piece unit is recommended. Only 2 wires are

required for connection between Display Module and Equipment Control

Module. These two wires (V+ and Vg) do not provide ordinary 24VAC. They

carry a combination of power and communications data that is unique to these

products.

A07052

Fig. 1 -- PCB Breakout Jumper

Models

There are programmable and non--programmable models for all applications.

They can be configured for AC or HP installations, allowing it to be used in

place of all Carrier thermostats. Programmable thermostats may be configured as

non--programmable if user desires.

Outdoor Temperature Sensor

The outdoor air temperature sensor is not included with the AC/HP Control. It is

available as an accessory, part number TSTATCCSEN01--B. Optimum

performance is obtained when an outdoor temperature sensor is used with the

AC/HP Control. Plan installation so that 2 wires can be run from Equipment

Control Module to an outdoor location, preferably on the north side of the house

or refer to Installation Instructions included with the outdoor temperature sensor

for simplified connection. Sensor can be mounted to outdoor unit and existing

dedicated sensor wires may be used for its connection. Details are provided in

sensor instructions.

Remote Indoor Temperature Sensor

A remote temperature sensor may be used with the programmable heat pump

and programmable air conditioner thermostats where it is desirable to install the

thermostat in a limited access location while measuring the temperature in the

living space. The remote room sensor may be used as a stand alone or average

with local sensor.

Two--Piece Thermostat Configuration

The Performance Series AC/HP Control can be installed in one of two

configurations. The control may be installed as a single--piece thermostat or it

may be split into two pieces and mounted in separate locations. As a single--piece

unit, all required wiring must be brought to the Equipment Control Module for

connection to the terminal strip. In two--piece configuration, the Display Module

can be mounted in the living space while the Equipment Control Module may be

mounted near the indoor furnace or fan coil. Connection from the display to the

Equipment Control Module requires only two wires. All other control wires are

connected to the Equipment Control Module from the HVAC equipment. This

configuration results in a slimmer display and locates the Equipment Control

Module containing the switching relays away from the main living space where

relay clicking will not be heard.

INSTALLATION

Carton contains the following components. See Fig. 2 for programmable models

or Fig. 3 for non--programmable models.

A07754

Fig. 2 -- TP--PAC / TP--PHP Carton Contents

1. Display Module

2. Stand--off for Equipment Control Module

3. Screws and pig tail

4. Equipment Control Module

A07755

Fig. 3 -- TP--NAC / TP--NHP Carton Contents

1. Display Module

2. Stand--off for Equipment Control Module

3. Screws and pig tail

4. Equipment Control Module

AC/HP Control Location

AC/HP Control should be mounted:

SApproximately 5 ft (1.5m) from floor.

SClose to or in a frequently used room, preferably on an inside parti-

tioning wall.

SOn a section of wall without pipes or duct work.

AC/HP Control should NOT be mounted:

SClose to a window, on an outside wall, or next to a door leading to the

outside.

SExposed to direct light or heat from a lamp, sun, fireplace, or other

temperature--radiating objects which could cause a false reading.

SClose to or in direct airflow from supply registers and return--air regis-

ters.

SIn areas with poor air circulation, such as behind a door or in an al-

cove.

Installer should determine whether control will be installed as single--piece or

two--piece. In single--piece configuration, as many as 14 wires may need to run

to wall mounting location for connection to the control. In two--piece

configuration, the Display Module and Equipment Control Module are

connected by two wires.

Install AC/HP Control

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal injury or

death.

Before installing AC/HP Control, turn off all power to

equipment. There may be more than 1 power disconnect.

!WARNING

UNIT DAMAGE HAZARD

Failure to follow this caution may result in equipment damage

or improper operation.

Improper wiring or installation may damage AC/HP Control.

Check to make sure wiring is correct before proceeding with

installation or turning on power.

CAUTION

1. Turn off all power to equipment.

2. If an existing thermostat is being replaced

a. Remove existing thermostat from wall.

b. Disconnect wires from existing thermostat, 1 at a time.

c. As each wire is disconnected, record wire color and terminal marking.

d. New or additional wires may be needed to accommodate added hu-

midity outputs.

e. Discard or recycle old thermostat.

Other manuals for A07049

This manual suits for next models

Table of contents

Other Carrier Thermostat manuals

Carrier

Carrier 33CS Manual

Carrier

Carrier Debonair 33CS220-FS User manual

Carrier

Carrier Performance TP-NHP User manual

Carrier

Carrier Aquazone 50QE900 User manual

Carrier

Carrier KSACN1001AAA User manual

Carrier

Carrier 53DFS250-SL User manual

Carrier

Carrier 33CS420-01 User manual

Carrier

Carrier TP -PRH User manual

Carrier

Carrier DEBONAIR 33CS User manual

Carrier

Carrier P/N 33CSSN2-MH User manual

Carrier

Carrier BASE SERIES PROGRAMMABLE THERMOSTATS TB-PAC User manual

Carrier

Carrier TP-WEM01 User manual

Carrier

Carrier 33CS User manual

Carrier

Carrier GAS FURNACE 58MVP Instructions and recipes

Carrier

Carrier 53DFST2-NP User manual

Carrier

Carrier Comfort Non-Programmable User manual

Carrier

Carrier 52M Performance Series User manual

Carrier

Carrier DEBONAIR 33CS Instructions and recipes

Carrier

Carrier TSTATCCPF701 User manual

Carrier

Carrier ComfortVu TBPL-24-H Operating instructions

Carrier

Carrier Cor TP-WEM01-A User manual

Carrier

Carrier User interface Comfort Module Series Operating manual

Carrier

Carrier 33CS User manual

Carrier

Carrier EDGE PRO 33CS2PP2S-01 User manual

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide

Honeywell

Honeywell T6811 quick guide