Carrier KVACN0101AC User manual

Installation and User Guide

READ AND SAVE THESE INSTRUCTIONS

The illustrations in this document are generic; your control appearance may be slightly different from the ones shown.

INSTALLATION

1. Unplug the ventilation unit.

NOTE: If the control is to be installed in an electric box, go to step 5.

2. Cut a 27/8" x 1¾" hole in a wall, at a convenient location for the

control. Route a cable (type 22/4) for the control from the unit to

this hole.

A200529

3. Temporarily place the control over the hole and mark both

mounting screw hole positions.

4. Remove the control, drill both screw holes (3/16" Ø) in wall and

insert the wall anchors (included).

A200530

5. Strip the end of the cable to access the 4 wires (about 3"). Strip the

end of each wire (about 1/4"). Connect the wires to the terminals,

regardless of the wire color. Note which wire color has been chosen

for each terminal.

A200531

6. Mount the control to the wall.

A200532

KVACN0101(B,C)AC

Automatic Control

WARNING

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury or death.

Electrical wiring must be done by qualified personnel in accordance

with all applicable codes and standards. Before connecting wires,

unplug the unit or switch power off at service panel and lock service

disconnecting means to prevent power from being switched on

accidentally. Always wear safety glasses and gloves while performing

these instructions.

CAUTION

PROPERTY DAMAGE HAZARD

Failure to comply with the following can cause damage.

If ducts have to go through an unconditioned space (e.g.: attic), always

use insulated ducts to prevent condensation formation inside and

outside ducts, which could cause material damage and/or mold growth.

Moreover, if fresh air to building duct and/or stale air from building

duct goes/go through an unconditioned space, the unit must be set to

operate continuously in cold conditions (below 10°C/50°F).

Continuous air movement inside ducts will prevent condensation

formation. The unit can be stopped temporarily for maintenance and/or

repair purposes in such conditions. (Refer to the main unit Installer

Manual for more details.)

A Carrier Company

Edition Date: 5/21 Catalog No: OM-KVACN-AC-01

Replaces: New

KVACN0101(B,C)AC: Installation and User Guide

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

7. Perform the electrical connection to the terminal connector of the

unit, as shown below. For more details, refer to the installation

manual of the ventilation unit.

NOTE: To avoid miswiring, refer to the notes taken at step 5 to match

the wire color with the right terminal.

A200533

8. Plug the ventilation unit and test the wall control.

HOW TO USE THE CONTROL

A200534

The main button works following this sequence:

Click 1 = RECIRC (if available)

Click 2 = INT

Click 3 = MIN

Click 4 = MED

Click 5 = MAX

Click 6 = OFF

and so on

The indicator lights up per the selected mode.

RECIRC—Recirculate air inside the house at MAX speed. Not

available on all units.

INT—Within a one hour period, the system will operate in MIN speed

for 20 minutes.

MIN/MED/MAX—Continuous exchange ventilation at selected speed.

• Press the TURBO button to get 4 hours of ventilation in MAX speed.

The TURBO indicator will light up. Once the 4-hour period is done,

the system will operate according to the previous setting.

• Press the AUTO button to let the system operate according to outdoor

temperature. The AUTO indicator will light up. The AUTO indicator

will light up and the system will operate as follows:

• Less than -25°C (-13°F) = 10 min/hr

• -25°C (-13°F) to -7°C (19°F) = 20 min/hr

• -7°C (19°F) to 10°C (50°F) = 40 min/hr

• 10°C (50°F) TO 25°C (77°F) = MIN speed

• 25°C (77°F) to 28°C (82°F) = 30 min/hr

• 28°C (82°F) to 33°C (91°F) = 20 min/hr

• Above 33°C (91°F) = 10 min/hr

• If the maintenance indicator is lit, it means that the filter needs to be

cleaned or replaced. Once the filter is cleaned or replaced, press the

AUTO button for five seconds to reset the maintenance indicator. If

the maintenance indicator flashes, the LCD screen on the unit will

give the error code. Refer to the Troubleshooting section in the

ventilation unit user guide for more information.

• At unit first boot, AUTO and TURBO indicators blink alternately for

about 1 minute. If indicators continue blinking after this period, it

means that the communication cannot be established with the

ventilation unit. Make sure wires are correctly connected to the wall

control and unit terminals (refer to step 7).

This manual suits for next models

Other Carrier Controllers manuals

Carrier

Carrier 37HS Series User manual

Carrier

Carrier 3V VVT 33ZCVVTZC-01 Installation manual

Carrier

Carrier WTC-RCI User manual

Carrier

Carrier PREMIERLINK 33CSPREMLK Operator's manual

Carrier

Carrier XCT 7 40VCI67FQEE Installation instructions

Carrier

Carrier 33ZCFANCOL Installation manual

Carrier

Carrier ZUI2 User manual

Carrier

Carrier WTC-RCI-S User manual

Carrier

Carrier 50CO Series Manual

Carrier

Carrier UC Open XP Installation manual

Carrier

Carrier i-Vu Open Link Installation manual

Carrier

Carrier 40VAM-C8FATEE User manual

Carrier

Carrier i-Vu MPC Open XP IO48/816 Installation manual

Carrier

Carrier Fan Coil Quick setup guide

Carrier

Carrier NTC 36CB User manual

Carrier

Carrier 38AKS User manual

Carrier

Carrier Micro-Link 5 User manual

Carrier

Carrier B Series User manual

Carrier

Carrier RTU Open v3 Quick setup guide

Carrier

Carrier CCU Use and maintenance manual

Carrier

Carrier 40VM Series User manual

Carrier

Carrier XCT 7 40VCC617FQEE Installation instructions

Carrier

Carrier A Series User manual

Carrier

Carrier TruVu VVTZC-E2 Installation manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual