Carrier Air V User manual

OWNER’S GUIDE

OPERATION & INSTALLATION

CARRIER RECREATIONAL VEHICLE

AIR CONDITIONER

HEAT PUMP UNIT FOR NON DUCTED SYSTEM

PRODUCT INFORMATION

Model Number

Date in Service

Unit Serial Number

Ceiling Assembly Serial Number

INSTALLER

Date of Installation

Name

Address

Phone

A FEW WORDS ABOUT YOUR NEW AIR CONDITIONING UNIT 2

ELECTRICAL DATA 2

OPERATING INSTRUCTIONS 3

ENJOYINGTHE “AIR SHOWER “5

ENERGY SAVING TIPS 5

INSTALLATION INSTRUCTIONS 6

Step 1. Selecting an Installation Location &

Installing the Roof Top Heat Pump Unit 6

Step 2. Installing the Ceiling Assembly 9

Step 3. Installing the Auxiliary Heater Assembly 10

Step 4. Electrical Wiring 10

Step 5. Completing the Installation 12

TROUBLE SHOOTING GUIDE 12

NORMAL MAINTENANCE PROCEDURES 13

PART DIAGRAM 14

CONTENTS

○○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○ ○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

OWNER’S GUIDE -

Allwiringmustcomply withlocal andnational electricalcodes. Allwiring mustbe installedby qualifiedelectricians.

If you have any questions about the following instructions, contact a qualified electrician.

Check the available power supply and resolve any wiring problems BEFORE installing and operating this unit.

This air conditioner is designed to operate from a 115V AC, 60Hz, 1 Phase power supply.

The unit nameplate is located on the left side of the condenser orifice that is on the rear of the basepan. The

wiring diagrams are located on the cover of the control box. The ceiling assembly unit wire diagrams are

located on the ceiling panel.

Note the unit’s model, serial number, and the ceiling assembly serial number. Record this information on the

front cover of this manual. Refer to Figure 4 of page 9 for serial number location.

A FEW WORDS ABOUT YOUR NEW

AIR CONDITIONING UNIT

Thank you for choosing the Air V, Carrier Recreational Vehicle Air Conditioner, for your comfort needs.

You can feel confident in your selection because the same pride in craftsmanship and engineering knowledge

that goes into Carrier equipment to cool the Astrodome in Texas, the famous Sistine Chapel in Rome,

the Washington DC Halls of Congress and thousands of other installations worldwide has gone

into the construction of your unit.

In addition to cooling the room, your Carrier heat pump unit will also heat, filter and dehumidify the room’s air.

An auxiliary electric resistance heating assembly is provided to take the chill out of the indoor air when the heat

pump can no longer operate. The heat pump will shut down at conditions which would cause outdoor coil freeze

up, generally near freezing temperatures.

The Air V air conditioners quietly give you maximum cooling and heating comfort. Now you can “Feel Carrier’s

comfort”!

This manual will supply you with all the information you need for installing, operating and maintaining your new unit.

Take a few minutes to discover how to get the most in cooling and heating comfort and economic operation from

your new Air V.

Please keep this manual handy for future reference, and be sure to send in your warranty card.

You can also contact us by the internet web site, www.airv.com .

ELECTRICAL DATA

OWNER’S GUIDE - 3

Schematic Diagram of Upper Unit

OPERATING INSTRUCTIONS

GLOSSARY OF CONTROL SYMBOLS

Automatic Thermostat Control

Air Sweep Control

Master Control

Schematic Diagram of Ceiling Unit

OWNER’S GUIDE -

When dial is turned to the OFF position the unit will NOT operate.

When leaving your vehicle for any period of time, make sure the

master control dial is set to the OFF position.

OW FAN will circulate relatively small quantities of air WITHOUT

cooling. Choose the OW FAN setting simply by rotating the dial

to this position.

HIGH FAN will circulate larger quantities of air WITHOUT cooling.

Choose the HIGH FAN setting simply by rotating the dial to this

position.

OW COO will providelightcooling. Choose the OW COO set-

ting simply by rotating the dial to this position.

It is also recommended for nighttime use or relatively hot days.

HIGH COO providesmaximumcooling.Choose theHIGH COO

setting simply by rotating the dial to this position.

It is recommended for quick cooling or extremely hot days.

Once the room is cooled, switch to a lower setting.

HEAT will provide comfort heating. Choose the HEAT setting

simply by rotating the dial to this position. The HEAT option is

recommended for cold days.

Works much like the thermostat on a home heating system and

has no effect on the fan speed. For cooler room condition rotate

thermostat dial clockwise toward COO ER position.

For warmer room condition rotate thermostat dial counterclock-

wise toward WARMER position.

OFF

HIGH FAN

LOW COOL

HIGH COOL

THERMOSTAT CONTROL

LOW FAN

HEAT

NOTE

The heat pump will operate on reverse cycle refrigerant heating

at outdoor temperatures above freezing, the heat pump com-

pressor will shut down to prevent outdoor coil freeze up. At this

time, the auxiliary electric resistance heater will be utilized to take

the chill out of the indoor air.

OWNER’S GUIDE -

1 2

AIR SWEEP CONTROL

Your unit provides an automatic air sweep to cool(or heat)

the room more efficiently. When the air sweep switch is set

on (|), the horizontal blade moves slowly up and down

and distributes the air around the room. The direction of

the vertical blades can be adjusted manually (make sure

the air sweep is off). With the air sweep in the off position,

the horizontal blade can be closed by pushing the PUSH

mark on the blade, and can be opened by pushing it

again.

|- Setting for automatic

air sweep on

- Setting for automatic

air sweep off

Keep the unit’s air filters clean. (See the Normal

Maintenance Procedures section of this manual

on page 13)

Selectthe thermostat settingthat suitsyourcomfort

needs and leave it at that chosen setting.

Your unit provides you with more efficient cooling

air with the direct air discharger. On extremely hot

days or after much activity, you can take an “air

shower” and cool off quickly. On a cold day you

can enjoy the heated air in the same way.

You can enjoy direct air by rotating the knob to

the open position and closing the front or rear

horizontal blade. (Closing the front blade may

provide direct air more efficiently)

ENERGY SAVING TIPS

Normal Position(Close) Enjoying the “AIR SHOWER”(Open)

ENJOYING THE “AIR SHOWER”

OWNER’S GUIDE -

1 2 3

Moving parts can cause personal injury. Be careful when test-running the unit.

Do not operate the unit with exterior cover removed.

WARNING

During extreme outdoor temperatures, the heat

gain of the vehicle may be reduced by:

- parking the vehicle in a shaded area

- keeping the windows and doors closed

- avoiding the use of heat producing appliances

- using window shades (binds and/or curtains)

For a more permanent solution to reduce the high

heat gain, window awnings and/or window glass

tinting should be considered.

Test run the unit with proper power supply outlet. Refer to the Operating Instructions section in this Owner’s Guide.

Make sure all the controls operate correctly then disconnect the power supply of the unit.

Your Air V unit has been designed for use in recreational vehicles.

Check the roof of the vehicle to determine if it supports both the roof top unit and the ceiling assembly without

additional support. Make sure the interior ceiling mounting area will not interfere with existing structures.

Once the location for your air conditioner has been determined, a reinforced and framed roof hole opening must

be cut (if there is no hole) or you may use existing vent holes.

Remove all screws which secure

the roof vent to the vehicle.

Remove the vent and any

additionaltrim. Carefullyremove

all chalking from around the

opening so the surface is clear.

INSTALLATION INSTRUCTIONS

BEFORE INSTALLATION

STEP 1 - SELECTING AN INSTALLATION LOCATION &

INSTALLING THE ROOF TOP HEAT PUMP UNIT

CASEA.

If a roof vent is already present in the desired mounting location for the air conditioner, the following steps must be

performed:

It may be necessary to seal

some of the old roof vent

mounting screw holes which

may fall outside of the air

conditioner basepan gasket.

Examine the roof opening size. If

the opening is smaller than 14”

14”, the opening must be

enlarged. If the opening

exceeds 14”14”, a mounting

plate (frame) must be

fabricated to reduce the

opening size (See Figure 1).

When using the heating system the heat loss of the

vehicle may be reduced by:

- parking the vehicle in a sunny area

- keeping the windows and doors closed

- avoiding the use of heat absorbing appliances

OWNER’S GUIDE - 7

CASE B.

If a roof vent opening is not used, a new opening (See Figure 1) will have to be cut into the vehicle roof. A matching

opening will also have to be cut into the interior vehicle ceiling. Be careful when cutting the ceiling opening because

if the ceiling opening is carpeted, snagging could occur. After the opening in the roof and interior ceiling are the

correct size, a framed support structure must be placed between the exterior roof top and interior ceiling. The

reinforced framed structure must follow the following guidelines:

Hole for Wires

• Allow 24” (working length) of supply wiring through the support frame and make sure that all wiring passing

through any mechanical structure must be protected from insulation chaffing using a rubber grommet or strain

relief.

• After the support frame is built and both the roof exterior and the interior ceiling are cut, make sure that the

electrical wiring can be routed to the control board. Seal the gap around the electrical supply wiring using a

rubber grommet.

• The roof top air conditioner must be mounted on a level plane from front to rear and side to side when the vehicle

is parked on a level plane. Figure 2 shows maximum allowable degrees that the Air V can be mounted above or

below level.

Figure 1

CAUTION

It must be capable of supporting both the weight

of the roof top air conditioner and the interior

ceiling assembly

It must be capable of holding the roof outer

surface and interior ceiling apart and supporting

them, so that when the roof top air conditioner

and ceiling assembly are bolted together, no

collapsing occurs.

We recommend that the spacing between the

vehicle roof top and the interior ceiling top be no

less than 3/4”. A typical support frame is shown in

Figure 1.

There must be an opening through the frame for

the power supply wiring. Route the supply wiring

through the frame at the same time the support

frame is being installed.

CAUTION

OWNER’S GUIDE - 8

ALLOWABLE OFFSET FOR CARRIER AIR CONDITIONERS

WITH CARRIER ROTARY COMPRESSORS

• If the roof of the vehicle is sloped (not level) such that

the roof top air conditioner cannot be mounted within

the maximum allowable degree specifications, an

exterior leveling shim will need to be added to make the

Air V level. A typical leveling shim is shown in Figure 3.

• Oncethe roof topair conditionerhas been leveled,some

additional shimming may be required above the interior

ceiling assembly. The roof top air conditioner and the

interior ceiling assembly must be square with each other

before they are secured together.

• After the mounting hole area is properly prepared,

remove the carton and shipping pads from around the

roof top air conditioner. Carefully lift the unit on top of

the vehicle. Do not use the outer plastic shroud for lifting.

Place the roof top air conditioner over the prepared

mounting hole.

• The pointed end (nose) of the shroud must face toward

the front of the vehicle. From inside the vehicle, pull the

electrical harness down from the roof air conditioner

through the mounting opening and let it hang.

* Height Varies

To Make Unit

Level

Above or Below

Level 10°Max.

Above Level 10°Max.

Below Level 0°Max.

Figure 2

Figure 3

ROOF TOP HEAT PUMP UNIT DIMENSIONS

NOTE

22.6"

16.7"

14" x 14"

OPENING

4.3"

41"

REAR OF

UNIT

10.3"

4.3"

OWNER’S GUIDE -

Carefully take the ceiling assembly out of the

carton. (The controls are factory installed in the

ceiling assembly.)

Remove the ceiling grille from the ceiling assembly

frame. And remove the heater assembly from the

ceiling assembly frame.

Before the ceiling assembly can be mounted to

the roof top air conditioner, the fabric duct collar

must be fastened to the basepan of the air

conditioner with 4 screws (See 햲, Figure 4).

Beforelifting(mounting) theceilingassembly, check

the gasket on the underside of the roof top air

conditioner. The gasket must be centered over the

roof opening.

Make sure that you have properly matched the roof top air conditioner and interior ceiling assembly. The following

step by step instructions must be performed in the following sequence to insure proper installation.

SERIAL NUMBER

OF UPPER UNIT

SERIAL NUMBER

OF CEILING UNIT

STEP 2 - INSTALLING THE CEILING ASSEMBLY

Secure the ceiling assembly frame to the roof top

air conditioner with the mounting bolts (See 햳,

Figure 4). You must start (thread) the mounting

bolts by hand to avoid cross-threading. DO NOT

START THE MOUNTING BOLTS WITH AN AIR GUN.

The mounting bolts should be tightened evenly.

Donot over-tighten eachbolt. Thebolt tightening

process is complete when the basepan gasket

has been evenly compressed to 60%.

Pull the fabric duct collar through the ceiling

assemblyframe openingand pullthefourcorners

to extend below the duct opening

(See 햴, Figure 4).

Figure 4

Before lifting the ceiling assembly, pull the fabric

duct collar so it hangs out of the way and does

not get caught under the ceiling assembly frame.

Other manuals for Air V

Table of contents

Other Carrier Air Conditioner manuals

Carrier

Carrier Puron 38TZA Operation manual

Carrier

Carrier 40GVC User manual

Carrier

Carrier 24ACB7 Comfort Operation manual

Carrier

Carrier Infinity 48XT A Series User manual

Carrier

Carrier 42BH Series Operation manual

Carrier

Carrier INFINITIR 15 SEER 48XT-A User manual

Carrier

Carrier TOSHIBA MML-UP0071H-UL User manual

Carrier

Carrier 38BA Dimensions and installation guide

Carrier

Carrier WeatherMaster 48HC04 Series Installation and user guide

Carrier

Carrier Niceday 42PHQ K Series User manual

Carrier

Carrier 38GXC User manual

Carrier

Carrier 50TC*17 Series Installation and user guide

Carrier

Carrier 48GP (N) 024-060 User manual

Carrier

Carrier 42 DWC Series User manual

Carrier

Carrier MMK-AP0073H2UL User manual

Carrier

Carrier 42XPP050 User manual

Carrier

Carrier Base 50ZPA Operation manual

Carrier

Carrier COMFORT 50ES-A Instruction Manual

Carrier

Carrier 40VMI Series User manual

Carrier

Carrier 42CT Series User manual

Carrier

Carrier KC_141P User manual

Carrier

Carrier 38BRC User manual

Carrier

Carrier 40SMC N Series Technical Document

Carrier

Carrier 42QZL018DS series User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual