Caple C670E/SS User manual

Instruction Manual
Electric
Fryer Electric
Barbecue
Model: C 680E/SS Model: C 670E/SS

2
Installation Requirements........................................................................................3
Installation ...............................................................................................................5
Electric Fryer Features............................................................................................8
Electric Barbecue Features ............................ .......................................................9
How to use your Electric Fryer ...........................................................................10
How to use your Electric Barbecue ....................................................................16
Your Guarantee ....................................................................................................19
Thank you for buying your new CAPLE Electric Fryer or Electric Barbecue. To ensure
that you get the best results from your new CAPLE Electric Fryer or Electric
Barbecue, we strongly suggest that you read this instruction manual thoroughly
before use. This manual contains installation advice, usage instructions and a clean-
ing guide, as well as other important facts about your CAPLE Electric Fryer or
Electric Barbecue. If treated with care, your CAPLE Electric Fryer or Electric
Barbecue should give you years of trouble-free cooking.
For Spare Parts, Technical Advice
or Product Service call the
CAPLE HELPLINE on 0870 241 1142
(Answerphone outside office hours)
Contents

3
Electrical Installation
– The appliance must be connected to
the mains by a competent electrician
and according to the regulations in
force.
– The appliance must be connected to
the mains checking first of all that
the voltage corresponds to the value
given on the rating plate and that
the section of the electrical cables
can take the load indicated on the
rating plate.
– Fit a standard plug which is suitable
for the power absorbed by the
appliance and in conformity with the
local rules in force.
– The plug must be put into a socket
connected to the earth system in
compliance with safety rules.
– For the United Kingdom:
As the colours of the wire of the
supply cable of this appliance may
not correspond with the colours
which identify the terminals of your
plug, proceed as follows:
– the yellow/green wire must be
connected to the plug terminal
marked with the letter E or with
the earth symbol or coloured
green or yellow/green;
– the blue wire must be connected
to the terminal marked with the
letter N or coloured black;
– the brown wire must be connected
to the terminal marked with the
letter L or coloured red;
Installation Requirements
IMPORTANT: Install the appliances
following the manufacturer's
instructions.
Incorrect installation can cause
damage to people, animals or
things, for which the manufacturer
cannot be held responsible.
– The connection can be made
directly to the mains by putting an
all-pole switch with minimum
opening between the contacts of 3
mm between the appliance and the
mains.
– The supply cable must not touch hot
parts and must be so positioned
that it does not exceed the
temperature of 75°C at any point.
– When the appliance is installed the
switch or socket must always be
accessible.
– The appliance must have its own
supply; any other appliances
installed near it must be supplied
separately.
–N.B. For connection to the mains
do not use adapters reductions or
shunts because these can cause
overheating or burning.
If the installation requires modifications
to the domestic electrical system or if
the socket and the appliance plug are
not compatible, contact a professional
electrician.
He must, in particular, also make sure
that the section of the socket cables is
suitable for the power absorbed by the
appliance.
The appliance must be connected to
the earth.
The manufacturer declines all
responsibility for any problem
caused by failure to observe this
instruction.

4
Repairs
Replacing the supply cable
Turn the cooktop over and unhook the
terminal board cover by inserting a
screwdriver into the two hooks “A”.
Open the cable gland by unscrewing
screw “F”, unscrew the terminal
screws and remove the cable.
The new supply cable, of suitable type
and section, is connected to the
terminal board following the diagrams
shown below.
Section of the supply cables
and connection diagram
The outer diameter of the supply
cable must not exceed 9 mm.
Supply cables section:
230 V ~ 50/60 Hz 3 x 1,5 mm2
for Electric Barbecue
use H05RR-F cables
for Electric Fryer
use the following cables:
H05VV-F
or H05V2V2-F resistant up to 90°C
or H05RN-F
A
F
Fig. 1
Fig. 2
230 V
PE
N
L1(L )2
Fig. 3
230 V~

5
Installation
Technical information
for the installer
Before installing the cooktop,
remove the protective film.
This cooktop can be built into a
working surface 30 to 40 mm
thick and 600 mm deep.
490
510
270
288
103 47
150
50
+ 0
– 2
+ 0
– 2
electric fryer
490
510
288
25 45
70
50
270
+ 0
–2
+ 0
–2
barbecue
Fig. 4
Fig. 5

6
Installation
To fit the cooktop into the unit make
an opening of the dimensions given in
the figure, remembering that:
– inside the unit there must be a
space of at least 30 mm between
the bottom of the cooktop and the
top of an appliance or bracket.
– any wall to the side and above the
cooktop must be at least 300 mm
away.
– the wall behind the cooktop must be
at least 50 mm away.
– when there is a wall unit or hood
above the cooktop there must be at
least 650 mm between the cooktop
and the unit or hood.
– the coatings of the walls of the unit
or appliances near the cooktop must
be heat resistant:
“X” protection against heating in
compliance with standards EN
60335-2 6.
Do not install the cooktop near
inflammable materials (e.g.
curtains).
650 mm
450 mm
300 mm
Fig. 6

7
Fastening the
appliances
Each appliance is supplied with a set
of tabs and screws to fasten it on
units.
– Cut the unit (as shown in the figure
on the previous page).
– Stretch gasket “D” over the edge of
the hole made being careful to
overlay the junction edges.
– Turn the appliance over and put
tabs “A” into the mountings; only
tighten screws “B” a few turns.
Make sure that the tabs are
mounted correctly as shown in the
figures at the side. Turn the tabs so
that the appliance can be put into
the hole.
– Put the cooktop into the hole cut
into the unit and position it correctly.
– Put tabs “A” into place, tooth “C" of
the tabs should go into the hole.
– Tighten screws “B” until the
appliance is completely secured.
– Using a sharp tool cut off the part of
gasket “D” which protrudes from the
cooktop.
A
A
AA
Fig. 7
Fig. 8
3 cm
min
3 cm
4 cm
B
D
A
C

8
Electric Fryer Features
Features
- Electrical insulation Class I.
1. Basket with draining hook and han-
dle which can be turned inwards
2. Oil tray
3. Tiltable electrical heating element -
1600 W
4. Pan cover
Description control panel
4. ON-OFF knob
5. Oil thermostat knob
6. Fryer ON indicator light
7. Oil temperature indicator light
Fig. 9
3
2
1
6
457
4
IMPORTANT SAFETY
REQUIREMENTS
• Do not introduce wet food to the fryer
at any time.
• Before use of the product ensure no
water residue is present within the
OIL CONTAINER or LID.
•Frozen Foods are frequently cove-
red with a coating of crystal which
should be removed prior to frying.
Lower the basket slowly to ensure no
boilover occurs.
•Never allow water near the fryer
during use to prevent the risk of
oil/water eruption.
• In the event of ignition, immediately
douse the flames using the fryer
cover and a dry towel (do not use
wet cloths).

9
Electric Barbecue Features
Features
- Electrical insulation Class 1.
- Protection against overheating of adjacent surfaces Type X.
1. Grill
2. Tiltable electric heating element - 2400 W
3. Tray with pumice stone
Description control panel
4. Heating element adjuster knob
5. Heating element ON indicator light
Fig. 10
5
2
3
1
4
1
2

10
Filling with oil
– Remove the pan cover and basket.
– Fill the tray with about 2 litres of oil
or fat for frying, already partly
melted. The level must be between
the minimum and maximum marks
printed on the tray.
– Make sure that the heating element
is completely lowered.
IMPORTANT: The heating element
must never be switched on when
it is out of the oil.
Cold area
The appliance is so constructed as to
allow an ample cold area under the
heating element for the solid particles
to settle. This helps the oil to last
longer and improves the frying which
will appear uniform, without burnt
spots.
Safety thermostat
The appliance has a manually reset
safety thermostat which turns the
appliance off when the temperature,
because of a fault, exceeds the set
temperature.
If this happens call the After-Sales
Service.
Using the fryer for the first
time
– Remove the adhesive film which
protects certain parts.
– Carefully remove all the glue
residues without using abrasive
substances, to avoid scratching the
surfaces.
– Remove the pan cover and the
basket, raise the heating element
and remove the oil pan.
– Wash and dry the tray and the
basket carefully (better if in the
dishwasher).
– Put the tray back into the fryer and
lower the heating element.
– Fill the tray with 3 litres of water.
– Switch the fryer on by turning the
changeover switch knob and turn the
thermostat knob to about 150°C.
This operation will clean the working
residues from the electric heating
element.
– Leave the fryer ON until the
water boils,then leave it to
cool down.
– Empty out the water and dry the tray
and heating element carefully.
– The fryer is ready for use.
MIN
MAX
Fig. 11 Fig. 12
How to use your Electric Fryer
This manual suits for next models
1
Table of contents

















