Canon Paper Craft User manual

Mountain fold (dotted line)

Make a mountain fold.

Valley fold (dashed and dotted line)

Make a valley fold.

Cut line (solid line)

Cut along the line.

Cut in line (solid line)

Cut along the line.

Tools

Scissors, glue, ruler, tweezers, pencil

![Caution] Glue, scissors and other tools may be dan-

gerous to young children so be sure to keep them out of

the reach of young children.

Assembly Instructions

Try to avoid bending the parts when you cut them out.

When assembling the parts, follow the assembly in-

structions and use the parts in the order given.

When sticking surfaces together, spread the glue evenly

and stick the parts together quickly and line up the

edges cleanly. While the glue is drying, put the fuse-

lage inside a sheet of paper and then press it down with

a book or similar in order to get a nice, straight finish.

When sticking the right and left wings together, make

sure that the center line is not off center.

Center line

To glue the wings flush onto the fuselage, use a pencil

or scissors to flatten out the part where the wings at-

tach to the fuselage.

Rub with pencil or scissors

to flatten out.

Flatten the uneven surface.

Cross section of the fuselage

To give the wings an angle, bend along a straight

ruler. (Refer to the assembly instructions for details on

what degree of angle to use.)

Dihedral angle

Attach the wings and horizontal stabilizer carefully so

that their center lines match up exactly with the center

line of the fuselage.

Make sure that the center line of

the wings matches up exactly

with the center line of the fuselage.

Also attach the horizontal stabilizer firmly.

Arrow points forward.

If any of the cut out parts are bent, this will seriously

affect the glider's performance. Therefore, be sure to

keep all parts perfectly flat till you join them up. For

the wings, stabilizer and other parts, use a ruler to

give you a proper straight edge to make your folds.

Align the parts

against a ruler to fold them.

Points to note when making the glider

http://www.canon.com/c-park/en/

- 1 -

Flying-Boat: Assembly Instructions

8mm approx.

(1/3")

Fold all tabs outward.

Aligning the noses flush,

glue

through

together

in the order shown.

Assemble the sponson. (Sponson: a projection on the side of the fuselage.)

Arrow points forward.

Arrows point forward.

Fuselage

Placing a ruler along the dashed line on both edges

of the main wing (

), bend the strips upward

to make a dihedral angle of 10˚.

Glue the main wing firmly to the fuselage.

Camber the main wing (

)

after the curve of its gluing position on the fuselage.

Glue

to the upperside of

aligning the dashed line

on both edges of

. When dry, cut off the protruding portions.

Glue the horizontal stabilizer

to the fuselage.

Glue the sponson

to the printed box on the left side

of the fuselage. Glue the sponson

to the printed box

on the right side of the fuselage.

View the fuselage from the front. Before the glue dries thoroughly,

fix the sponsons

and

to ensure that they are glued horizontally.

Insert a pencil into the sponson and swell it

again to make it into a streamline shape.

Fold all tabs on

. Swell the inside of the two folds of

Then spread glue on the shaded portion

as shown in the figure and glue the part

together to complete its bag shape.

Assemble part

in the same manner.

GLUING INSTRUCTIONS

Glue the parts together in the order indicated.

- 2 -

Flying-Boat: Assembly Instructions

10˚

Using the engine installation lines and cuts on the main

wing as a guide, glue the four engines to the main wing.

Adjust the camber of both the main wing

and the wing tips carefully with your fingers.

Using the dihedral angle gauge, make sure

the dihedral angle for the main wing is 10˚.

View the plane from both the front and the back

and straighten any warps or bends in the fuselage

and the wings.

Camber the wing tips carefully.

Camber the wing carefully.

Dot towards the front.

According to the curve of the gluing position

for the main wing on the fuselage,

camber the main wing (

) evenly up

to both edges. Make sure that the dihedral

angle for the folded tabs are 10˚.

Camber both wing tips

and

equally to the main wing.

Apply glue to the top surface of the folded tabs of the

main wing and attach wing tips

and

respectively.

Before it dries, adjust the dihedral angles of

and

to 10˚. (Use the dihedral angle gauge.)

Fold the tabs on

through

Glue together

and

to make four engines.

FINISHING TOUCHES

Give the finishing touches to the plane after it dries thoroughly.

- 3 -

Flying-Boat: Assembly Instructions

Other Canon Toy manuals

Canon

Canon Creative Park Nikko Toshogu Shrine Yomeimon User manual

Canon

Canon Supersaurus User manual

Canon

Canon CREATIVE PARK 3D Paper Mosaic (Tropical... User manual

Canon

Canon Creative Park Pop-up Card (Snowman) User manual

Canon

Canon Creative Park Rabbit User manual

Canon

Canon Nippon Maru User manual

Canon

Canon Creative Park Ragdoll Programming manual

Canon

Canon PAPER CRAFT Tyrannosaurus rex User manual

Canon

Canon PAPER CRAFT Rainbow beetle User manual

Canon

Canon creative park User manual

Canon

Canon CREATIVE PARK 3D Decoupage User manual

Canon

Canon Creative Park Mallet of Luck User manual

Canon

Canon Creative Park Hippopotamus User manual

Canon

Canon Creative Park Chinese Phoenix User manual

Canon

Canon Creative Park JAGUAR XKR User manual

Canon

Canon Creative Park Pop-up Card Halloween/Black cat &... User manual

Canon

Canon CREATIVE PARK Sea lion User manual

Canon

Canon Creative Park Crocodile User manual

Canon

Canon creative park Quick start guide

Canon

Canon CREATIVE PARK Yajirobe User manual

Canon

Canon CREATIVE PARK Pop-up card (Swings) User manual

Canon

Canon Creative Park Clowns on Stilts Line Dance User manual

Canon

Canon Paper Craft Catcher Instruction manual

Canon

Canon Science Papercraft Biology Series User manual

Popular Toy manuals by other brands

marklin

marklin 37321 instruction manual

GREAT PLANES

GREAT PLANES Pitts M-12S instruction manual

NOCH

NOCH 14261 manual

Hausler

Hausler 450 SE V2 quick start

Dynaflite

Dynaflite Daydream instruction manual

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Build instructions

Kenner

Kenner Batman 63651 instructions

LEGO

LEGO 8527 instructions

iKarus

iKarus ECO 8 Assembly instruction

Multiplex

Multiplex EasyStar II Building instructions

Walkera

Walkera 38 User handbook

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE manual

MD MXION SWD user manual

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway instructions

marklin

marklin 39671 user manual

Meccano

Meccano 15103 instructions

LEGO

LEGO TECHNIC 8735 instructions

Mattel

Mattel HOTWHEELS DWL04 instructions