Canon Creative Park Elastic-powered Bus Quick start guide
Actual size illustration:
check the size of your rubber bands here.
How to assemble your model neatly
Scoring along the fold lines in advance with a dried
up pen or a ruler with slightly sharp corners will result
in a neater model.
*Be careful not to press too hard as the paper may tear.
Caution
Keep scissors and glue away from small children.
Be careful not to cut your fingers when using scissors.
Scissors line Mountain fold
Cut in line Valley fold
Glue spot
Notation Key
About 1.57 inches in diameter
1. Carefully cut out the parts.
2. Fold along the dotted lines, making mountain
or valley folds as indicated.
3. Attach the glue spots on each part together.
4. Glue the parts together, and you’re done!
*Please read the Assembly Instructions
carefully before you begin.
Tools
Scissors
Glue (We recommend quick-drying paper glue)
3 rubber bands (preferably brand new ones)
Assembly Instructions
Elastic-powered Bus : Assembly Instructions
Assemble the tires
Glue Glue
Back
Fold in half along the fold lines,
glue together at the back and make a ring.
Adding curves to the part first will make it
easier to form a ring.
After gluing parts M and N together back to back,
attach the ring you have made.
Follow the same process to assemble G, H and I.
Assemble the axle
Add curves by pressing and rolling it
against the corner of a table,
with the printed side face up.
Fold the edge to make a triangular prism,
and roll the piece up to form a stick
(about 4mm wide).
Wind part E around and glue it down.
Glue down the end after rolling.
Cut three, equally-spaced slots in both
ends of part D, up to the red valley fold line,
and bend them back.
*The fine strips of paper are thick and hard
so be careful of paper cuts.
Glue
Attach part L, enveloping
it around the parts you cut
and bent back.
Attach the other side too.
Attach part P to both ends.
Follow the same process to
assemble the other axle.
Diagram from above
Elastic-powered Bus : Assembly Instructions
Assemble the front and back wheels
If necessary, cut off the ends.
Cut the rubber band
to make a string.
Tie one end of the band to the band stopper,
and the other end to the middle of the axle.
Assemble the body interior
Assemble as shown in the diagram. Attach part K to part R.
Attach the axles
Follow the fold line,
and glue together
at the back.
Assemble part S, and attach the area with
the diagonal lines to the inside of the body.
Fit the axles into the grooves of the body.
Check that the wheels spin smoothly.
Attach the tires to both ends of the axle.
Follow the same process to assemble
the back wheels.
*The axle of the back wheels does not
have an rubber band attached.
Elastic-powered Bus : Assembly Instructions
On the front wheel side, slot the
protruding parts into the slots.
Attach.
Pull the band stopper through the hole in part R.
Be careful that the band doesn't come undone.
The front wheels (with the bigger tires) can be
removed and changed.
Wind the rubber band around
the front wheels (with the bigger tires).
Assemble the body
Glue
Fold in half along the fold line,
and glue together at the back.
Assemble part J for the other side,
in the same way.
Glue the parts to connect
them together as shown.
Turn over the body, attach the assembled
body interior, and you're done!
Be careful that the gluing positions don't shift.Assemble as shown in the diagram.
Follow the fold line,
and glue together
at the back.
Follow the fold line,
and glue together
at the back.
Body (front)
Body (back)
Body (left)
Body (right)
Elastic-powered Bus : Assembly Instructions
How to play
Pull the car backwards along the ground, gently pushing down on the front wheels.
Point the car in the direction you want it to run, let it go and watch it take off!
Be careful not to wind the band too tightly as it may snap or come untied.
Play with it on a flat surface such as a table or the floor (wooden floorboards work better than carpet).
Glue
If your car doesn't run well, check the following points to repair it.
Are the axles or tires stuck against the body? Are the wheels or tires bent?
Has the band lost its elasticity? Is the band wound up too tightly?
Has the band come loose from the tire? Is the band tangled up around the axle?
Have a contest to see who can get
their bus closest to the bus stop.
Elastic-powered Bus : Assembly Instructions
Table of contents
Other Canon Toy manuals
Canon
Canon CREATIVE PARK Fractional Cake User manual
Canon
Canon Creative Park Pop-up Card Christmas House User manual
Canon
Canon Grand Piano User manual
Canon
Canon Paper Craft Snowy owl (Female) User manual
Canon
Canon Paper Craft Tower Bridge England User manual
Canon
Canon CREATIVE PARK Lion Dance User manual
Canon
Canon Creative Park Rabbit User manual
Canon
Canon PAPER CRAFT Giraffa stag beetle User manual
Canon
Canon Thoroughbred User manual
Canon
Canon PAPER CRAFT Whooper Swan User manual
Canon
Canon Creative Park Moving Clown in a barrel User manual
Canon
Canon Creative Park Kissing Dolls Pattern User manual
Canon
Canon CREATIVE PARK Sea lion User manual
Canon
Canon Chevrolet Confederate User manual
Canon
Canon Creative Park Clowns on funny unicycles User manual
Canon
Canon CREATIVE PARK Moving Money Box: Pig User manual
Canon
Canon CREATIVE PARK Sugar Glider User manual
Canon
Canon PaperCraft Gift Box E User manual
Canon
Canon CREATIVE PARK (Moving) Clowns spinning... User manual
Canon
Canon CREATIVE PARK Komatsu Special Vehicle 04... User manual
