Canon PIXMA MG6320 User manual
PIXMA MG6300
Setup Guide
© CANON INC. 2012
series
Setup Guide
This guide provides information for setting up a network connection for the printer.
Network Connection
Wireless Connection
Preparation for Connection
Printer Setup
Setup Procedure Selection
Push Button Method
Standard setup
WPS
Other setup (Advanced setup)
Disable
WEP
WPA/WPA2
Wired Connection
Preparation for Connection
Cable Connection
Printer Setup
Character Entry
Troubleshooting
Network Connection
Wireless Connection
aPreparation for Connection
Before Starting Wireless Connection Setup
1. Make sure that the printer is turned on.
If the power is on, the POWER lamp (A) will be lit.
Notes on Wireless Connection
Make sure that the computer is connected to the access point (A) (or wireless network router) you want to connect your
printer to.
The confi guration, router functions, setup procedures and security settings of the network device vary depending on your
system environment. For details, refer to the manual of your network device or contact its manufacturer.
Check if your device supports IEEE802.11n, 802.11g or 802.11b.
If your device is set to the "IEEE802.11 n only" mode, WEP or TKIP cannot be used as a security protocol. Change the
security protocol for your device to something other than WEP and TKIP or change the setting to something other than
"IEEE802.11 n only."
For offi ce use, consult your network administrator.
Take added care when connecting to a network that is not protected with security measures, as there is a risk of disclosing
data such as your personal information to a third party.
This printer cannot be used over wireless and wired connections at the same time.
An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without an
access point, is not supported. Be sure to prepare an access point.
bPrinter Setup
1. If the HOME button (A) on the printer is lit, touch the HOME button.
•
•
•
•
•
•
•
•
2. Flick the screen left or right, then tap the WLAN setup icon.
The (blue) Wi-Fi lamp (A) lights up when wireless connection is enabled.
cSetup Procedure Selection
The printer will automatically search for access points supporting WPS (Wi-Fi Protected Setup).
* If the Push Button Method screen is displayed on the printer
When you are unsure if your access point or router supports this technology, tap To other connection
methods.
Proceed to the screen for Standard setup.
Push Button Method → d-A Select the most suitable connection method from the following.
Standard setup → d-B
Connect to Access Point by entering the Network Password
WPS → d-C
Connect to WPS-compatible Access Point
Other setup (Advanced setup) → d-D
Connecting to the Network by Entering the Access Point's Settings
Directly on the Printer
When using WEP key number 2, 3 or 4, select "Advanced setup".
•
•
•
d-A Push Button Method
dConnection Using WPS
1. Press and hold the WPS button on the access point.
For details on pressing the WPS button, refer to the access point manual.
2. Tap Start setup on the printer within 2 minutes.
The (blue) Wi-Fi lamp on the printer fl ashes while searching for or connecting to the access point.
3. When the left screen appears, tap OK.
The network connection setup is now complete.
d-B Standard setup
dConnection via Standard setup
1. Tap Standard setup.
2. Tap your access point.
3. One of the screens below will be displayed on the printer.
4. Tap the screen.
5. Enter the network password (WEP key or passphrase).
Character entry is case-sensitive.
6. Tap Apply.
7. Make sure that the network password is correct.
Character entry is case-sensitive.
8. Tap OK.
9. When the left screen appears, tap OK.
The network connection setup is now complete.
d-C WPS
dConnection Using WPS
1. Tap WPS.
2. Tap Push button method.
3. Tap OK.
4. Press and hold the WPS button on the access point.
For details on pressing the WPS button, refer to the access point manual.
5. Tap OK on the printer within 2 minutes.
The (blue) Wi-Fi lamp on the printer fl ashes while searching for or connecting to the access point.
6. When the left screen appears, tap OK.
The network connection setup is now complete.
d-D Other setup (Advanced setup)
dConnection via Advanced setup
1. Tap Other setup.
2. Tap Advanced setup.
3. Tap your access point.
4. Tap the security protocol used by the access point.
Disable
5. When the left screen appears, tap OK.
The network connection setup is now complete.
WEP
5. Tap the WEP key number you want to use.
6. Tap the screen.
7. Enter the WEP key.
Character entry is case-sensitive.
8. Tap Apply.
9. Make sure that the WEP key is correct.
10.Tap OK.
11. When the left screen appears, tap OK.
The network connection setup is now complete.
WPA/WPA2
5. Tap the screen.
6. Enter the passphrase.
Character entry is case-sensitive.
7. Tap Apply.
8. Make sure that the passphrase is correct.
9. Tap OK.
10.When the left screen appears, tap OK.
The network connection setup is now complete.
Other manuals for PIXMA MG6320
5
This manual suits for next models
6
Table of contents
Other Canon All In One Printer manuals
Canon
Canon Staple Finisher-S1 User manual
Canon
Canon PIXMA MX420 Series Manual
Canon
Canon PIXMA TS6240 User manual
Canon
Canon Color imageCLASS X LBP1127C User manual
Canon
Canon MultiPass C560 Manual
Canon
Canon MG3600 series Setup guide
Canon
Canon MX520 series Setup guide
Canon
Canon 4235i User manual
Canon
Canon PIXMA MP990 User manual
Canon
Canon imageCLASS MF269dw User manual
Canon
Canon imageCLASS MF4890dw Safety guide
Canon
Canon imageCLASS MF6500 Series User guide
Canon
Canon PIXMA MP460 Instruction Manual
Canon
Canon 330 User manual
Canon
Canon imageRUNNER ADVANCE C9270 PRO Assembly instructions
Canon
Canon ImageRUNNER ADVANCE DX C5760i Installation guide
Canon
Canon imageCLASS D530 User manual
Canon
Canon Color imageCLASS MF8080Cw Safety guide
Canon
Canon PIXMA MG5520 User manual
Canon
Canon ImageCLASS 2300 Manual
