CAME Ferni Series User manual
F ERNI K I T
CAME UNITED KINGDOM LTD
ORCHARD PARK INDUSTRIAL ESTATE
TOWN STREET, SANDIACRE,
NOTTINGHAM, NG10 5BP
TEL: 0115 921 0430
FAX: 0115 921 0431
INTERNET - www.came k.com
E-MAIL - enq iries@came k.com
TECHNICAL
HELPLINE
0115 921 0430
Installation Instructions
for a “Single” gate...
THE FERNI-S KIT CONSISTS OF:
1 X FERNI MOTOR
1 X CONTROL PANEL
1 X RADIO FREQUENCY CARD
1 X TUNED ANTENNA
2 X REMOTE CONTROL TRANSMITTERS
1 X PAIR SAFETY PHOTOCELLS
THESE INSTRUCTIONS WILL SHOW YOU HOW TO INSTALL
A FERNI MOTOR TO A SINGLE GATE.
PLEASE READ THESE INSTRUCTIONS AND DIAGRAMS
CAREFULLY BEFORE STARTING ANY WORK.
UNDER NO CIRCUMSTANCES SHOULD THIS EQUIPMENT BE OPERATED UNLESS FITTED TO A GATE.
FAILURE TO COMPLY WILL INVALIDATE THE GUARANTEE.
INTRODUCTION
INSTALLATION INSTRUCTIONS
CONTENTS
1) Stage 1:- Civil & Mechanical Section Page
1.1 PRE-INSTALLTION CHECK 3
1.2 MOUNTING THE MOTOR BASE PLATE 4
) Stage :- Wiring & Electrical
2.1 FITTING THE CONTROL PANEL IN THE CASING 6
2.2 BASIC CABLE LAYOUT 7
2.3 LOW OLTAGE CABLE LAYOUT 8
3) Stage 3:- Installation Section
3.1 INSTALLING THE MOTORS 10
3.2 INSTALLING THE DRI E ARMS 11
3.3 ADJUSTING THE OPEN & CLOSED CAMS 12
4) Stage 4:- Wiring & Electrical ( )
4.1 WIRING THE MOTORS 14
4.2 WIRING THE SAFETY PHOTOCELLS 15
4.3 INSERTING THE FREQUENCY CARD 15
4.4 WIRING IN THE TUNED ANTENNA 16
4.5 CODING THE REMOTE CONTROLS 16
4.6 POWERING UP THE CONTROL PANEL 16
5) Stage 5:- Commissioning the control Panel
5.1 INITIAL WIRING & CONTROL PANEL SETUP 18
5.2 OPENING & CLOSING THE GATES 19
5.3 CONTROL PANEL ADJUSTMENTS 20
5.4 AUTOMATIC CLOSE & SAFETY PHOTOCELLS 21
5.5 PROGRAMMING THE REMOTE CONTROLS TO THE
CONTROL PANEL 22
5.6 FINAL ASSEMBLEY 23
6) Troubleshooting Guide 25
7) Technical Information
7.1 TECHNICAL SPECIFICATIONS 27
7.2 MOTOR TORQUE SETTINGS 28
7.3 ZA5 CONTROL PANEL DESCRIPTION 29
7.4 ZA5 WIRING DIAGRAM 31
7.5 CONTROL PANEL ADJUSTMENTS 32
7.6 ELECTRICAL CONNECTIONS 33
8) Contact Information
3
STAGE 1
CIVIL & MECHANICAL SECTION
1.1 - Pre-Installation Check
BEFORE BEGINNING YOUR FERNI S GATE INSTALLATION CHECK THE
FOLLOWING:
THE GATE POST OR PIERS ARE STRONG ENOUGH TO SUPPORT THE GATE
AND THE MOTOR
THE GATE IS STRONG ENOUGH TO BE AUTOMATED.
THE GATE SWINGS FREELY FROM OPEN TO CLOSE AND THERE IS NO
FRICTION ON THE HINGS.
Fig 1
IF DISTANCE B IS 0 TO 300mm: DISTANCE A MUST BE AT LEAST 110mm.
IF DISTANCE B IS 300mm TO 380mm: DISTANCE A MUST BE AT LEAST
150mm.
4
1. - Mounting the Motor Base Plate
USING SUITABLE ANCHOR BOLTS OR CHEMICAL RESIN FOR BRICK PIER
SECURITY MOUNT THE MOTOR PLATE TO THE BRICK PIER.
FOR WOODEN POSTS IT IS AD ISED TO FIX THE MOTOR PLATE TO THE
POST. A THREADED BAR SHOULD BE PLACED ALL THE WAY THROUGH THE
POST THEN BOLTED. Fig 3
Fig 2
WHEN MOUNTING THE MOTOR PLATE BE SURE TO RESPECT THE 150mm
DIMENSION FROM THE BOTTOM OF THE MOTOR PLATE TO GROUND LE EL.
THIS IS TO ENSURE SUFFICIENT CLEARENCE FOR THE TRANSMISSION
DRI E ARM TO BE INSERTED THROUGH THE MOTOR.
ENSURE THAT THE DISTANCE BETWEEN THE CENTRE OF THE FRONT
BRACKET ‘A’ 450mm. THE FRONT GATE BRACKET MUST BE FIXED LOWER
THAN THE MOTOR PLATE BY 19mm AS SHOWN
150 mm 19mm
Fig 4
Bracket “A”
Base Plate
5
BEFORE STARTING STAGE - Wiring & Electrical
PLEASE CHECK THAT YOU HAVE CORRECTLY:
Ref Page
1. Checked Requirements 1.1 3
. Mounted Motor Base Plate 1. 4
NOW STAGE 1 IS FULLY COMPLETED YOU ARE READY TO
BEGIN STAGE OF YOUR FERNI AUTOMATION KIT
INSTALLATION
END OF INSTALLATION
STAGE 1
6
STAGE - WIRING & ELECTRICAL
.1 - Fitting the Control Panel in the Casing
Screws
Screw positioning holes
Green connector point
Fastening screws
Securely fasten the control panel PCB to the
casing with the screws supplied.
Plug the green connector from the transformer to
the PCB ensuring that it connects the correct way.
NB FROG Series Motors: connect the black wires
coming out of the board to one capacitor.
7
. - Basic Cable Layout
Fig 5
THIS DIAGRAM DETAILS THE BASIC CABLE LAYOUT FOR
A SINGLE MOTOR.
THE POWER SUPPLY TO THE CONTROL PANEL SHOULD BE LI E AND
PROTECTED IN ACCORDANCE WITH THE 16TH EDITION ELECTRICAL
REGULATIONS. THE SUPPLY SHOULD BE RATED AT A MINIMUM OF 6 AMPS.
WHEN INSTALLING WIRES OUTDOORS THE CABLE APPROACH TO ALL
DE ICES MUST BE FROM BELOW TO CREATE A “DRIP-LOOP” AND THEREBY
A OID UNNECCESSARY WATER INGRESS.
WHEN INSTALLING LOW OLTAGE CABLE AROUND THE GATEWAY IT IS
AD ISED TO PUT ALL LOW OLTAGE CABLE IN EITHER DUCTING OR
ALKATHENE PIPING. ALL CABLE JOINTING SHOULD BE CARRIED OUT
ABO E GROUND.
Joint Box
3 Core 1.5mm SWA
Control Panel
4 Core Flex
8
.3 - Low Voltage Cable Layout
Fig 6
ALL CAME ACCESSORIES CAN BE WIRED 0.2m STRANDED CABLE (BUGLAR
ALARM TYPE). THE TUNED ANTENNA SHOULD BE WIRED WITH COAXIAL
CABLE (RG59).
Joint Box
Low oltage
4 Core Flex
Control Panel
Safety Photocells
Tuned Antenna
Coaxial Cable
3 Core SWA 1.5m
BEFORE STARTING STAGE 3 - Installation
PLEASE CHECK THAT YOU HAVE CORRECTLY:
Ref Page
1. Fitted the Control Panel in the Casing .1 6
. Installed Basic Cable Layout . 7
. Installed Low Voltage Cable Layout .3 8
NOW STAGE IS FULLY COMPLETED YOU ARE READY TO
BEGIN STAGE 3 OF YOUR FERNI AUTOMATION KIT
INSTALLATION
END OF INSTALLATION
STAGE
9
Other manuals for Ferni Series
5
This manual suits for next models
1
Table of contents
Other CAME Gate Opener manuals
CAME
CAME FA7024CB User manual
CAME
CAME BX708ALS User manual
CAME
CAME A 3006 User manual
CAME
CAME ZLX24MA User manual
CAME
CAME ATS30DGS User manual
CAME
CAME ATS-S524 KIT User manual
CAME
CAME BKS08AGS User manual
CAME
CAME Ferni Series Operating instructions
CAME
CAME F1000 User manual
CAME
CAME FROG MD User manual
Popular Gate Opener manuals by other brands
SOMFY
SOMFY Dexxo RTS Pro INSTALLATION INSTRUCTIONS-ILLUSTRATIONS
Cardin
Cardin BL Series manual
Westfalia
Westfalia 85 27 06 instruction manual
Extel
Extel VERA quick guide
Comunello Automation
Comunello Automation ABACUS 220 Installation and user manual
Mighty Mule
Mighty Mule 200 E-Z GATE OPENER UL325 SERIES installation manual