Calculated Industries 4088 User manual
2— Machinist calc®Pro 2
MACHINIST CALC®PRO 2
The Machinist Calc®Pro 2 Advanced Machining Math +
Materials calculator (Model 4088) provides hundreds of fast,
processes and 3 tools will let you spend much less time looking
Internet and more time machining.
The Machinist Calc Pro 2 gives you hundreds of calculations,
including:
TABLE OF CONTENTS
GETTING STARTED.................................................................4
..................................................................4
.............................................................5
..................................................5
.......................................7
................................................7
...............................................8
.......................................................8
.........................................................13
User's Guide — 3
USING THE MACHINIST CALC PRO 2 .................................15
...........................................................15
.............................15
Materials .............................................................................15
...........................................................................
Tools ...................................................................................17
.......................................................17
Basic.......................................................................17
Face Milling ............................................................18
End Milling ..............................................................19
IPM.................................................................
Based on Cutting Feed and RPM
(for Turning) ........................................................................
Based on Cutting Feed and RPM
(for Drilling) .........................................................................
Based on Feed per Tooth, RPM and
# of Teeth............................................................................
End Milling .....................................................
SFM.......................................................
Turning.....................................................
End Milling ...............................................
Drilling......................................................
..................................
Based on Cutting Feed and # of Teeth...
Based on Feed Rate, RPM and
# of Teeth............................................................................
Face Milling ............................................
IPR ..........................................................31
Based on Feed per Tooth and # of Teeth...31
Based on Feed Rate and RPM ..................
Turning .......................................................33
.........................................................................34
......................................................34
..........................................................35
............................................................
....................................................37
.........................................................................37
...................................................................38
4— Machinist calc®Pro 2
..............................................................39
............................................................40
..................................................40
..................................................41
...............................41
............................41
..........................................................43
........................................................45
..............................................................47
................................................49
.....................50
............................................................................50
Known Thread Size and
Wire Size ............................................................................51
Known 3-Wire Measurement
and Wire Size .....................................................................
.....................................................................54
.........................................................................54
...........................................
Based on Adjacent and Opposite Legs ....
Based on Hypotenuse and Angle .............57
.....................................................58
Based on Diameter ..................58
..............58
...............................58
..........................................59
.....................................................59
APPENDIX ..............................................................................
GETTING STARTED
KEY DEFINITIONS
You may want to practice getting a feel for your calculator
User's Guide — 5
Basic Function Keys
O On/Clear Key —
clears all non-permanent values.
gO Off —
permanent values.
+-*
,= Arithmetic operation keys
0-9
and .
gConvert —
special functions.
gr Store —
gr
1-9
Storage Registers M1 through M9 —
store values in memory registers 1 through 9.
rRecall —
values and settings.
rr Memory Clear —
and displays total.
MAccumulative Memory — Adds displayed value to
Accumulative Memory.
gM M- —
Accumulative Memory.
Dimensional Function Keys
m Millimeters (mm) —
millimeters, with repeated presses toggling
Also converts dimensional value to units of
millimeters, with repeated presses toggling
6— Machinist calc®Pro 2
g5 Centimeters (cm) —
centimeters, with repeated presses toggling
g9 Meters (m) —
and volume units.
g7 Feet —
presses of g7
area and volume units. Also used with iand
/
presses of g7 during conversions toggle
iInch —
/
for entering fractional Inch values (e.g.,
9i1/2
decimal Inches.
/Fraction Bar —
fractional accuracy setting is automatically
dimensional fractional format.
B1/1000" (mils) — Multiplies a dimensionless
and displayed to three decimal places.
User's Guide — 7
Weight and Volume Function Keys
g6 Tons — Enters or converts a weight or volume
value to tons.
g4 Pounds (lbs) — Enters or converts a weight or
volume value to pounds.
g3 Metric tons (met tons) — Enters or converts a
weight or volume value to metric tons.
g2 Grams — Enters or converts a weight or
volume value to grams.
g1 Kilograms (kg) — Enters or converts a weight
or volume value to kilograms.
g0 Weight per Volume (wt/vol) —
Trigonometric Function Keys
ga Sine —
degree or unitless value.
gm ArcSine —
go Cosine —
degree or unitless value.
gi ArcCosine (ArcCos) —
gh Tangent (Tan) —
entered degree or unitless value.
8— Machinist calc®Pro 2
g/ ArcTangent (ArcTan) —
for the entered or calculated Tangent value.
Miscellaneous Functions
g. Degrees:Minutes:Seconds (dms◄►deg) —
the two formats.
%Percentage —
g% x2—
ABackspace Function —
one keystroke at a time (unlike the O
function, which deletes the entire entry).
gA Square Root (!) —
g, Reciprocal (1/x) —
8g,= 0.125).
g* Clear All —
g- Change Sign (+/-) — Toggle displayed value
g+ Pi — π
g= Preference Settings (Prefs) — Accesses
dimensional answer formats
(see Preference Settings section).
Machinist Function Keys
Note:Unitless entries are assumed to be inches in U.S. mode,
millimeters in Metric mode.
User's Guide — 9
dDiameter —
gd Bolt Pattern —
xand ycoordinates for each
xand ycoordinates.
NMaterial —
gN Depth of Cut (DOC) —
PProcess —
gP Width of Cut (WOC) —
LTool —
particular Tool Type.
10 — Machinist calc®Pro 2
gL Length of Cut (LOC) —
SSurface Feet per Minute — Enters or calculates
gS Wire Size —
RRevolutions per Minute — Enters or
gR 3-Wire Measurement (3W Measure) — Enters or
on this entered measurement.
TInches per Tooth — Enters or calculates
This manual suits for next models
1
Table of contents
Other Calculated Industries Calculator manuals
Calculated Industries
Calculated Industries ProjectCalc Plus MX 8528 User manual
Calculated Industries
Calculated Industries ElectriCalc LT User manual
Calculated Industries
Calculated Industries Quilter's FabriCalc 8400 User manual
Calculated Industries
Calculated Industries Construction Master 5 User manual
Calculated Industries
Calculated Industries TimeCard Tabulator II User manual
Calculated Industries
Calculated Industries PROJECTCALC CLASSIC 8503 User manual
Calculated Industries
Calculated Industries 8527 User manual
Calculated Industries
Calculated Industries 3420 User manual
Calculated Industries
Calculated Industries NautiCalc Plus User manual
Calculated Industries
Calculated Industries 8015 User manual
Calculated Industries
Calculated Industries Machinist Calc 4086 User manual
Calculated Industries
Calculated Industries 3415 User manual
Calculated Industries
Calculated Industries Material Estimator User manual
Calculated Industries
Calculated Industries 3430 User manual
Calculated Industries
Calculated Industries 3405 User manual
Calculated Industries
Calculated Industries 6260 User manual
Calculated Industries
Calculated Industries Hot Rod Calc 8703 User manual
Calculated Industries
Calculated Industries KitchenCalc 8300 User manual
Calculated Industries
Calculated Industries Construction Master IV User manual
Calculated Industries
Calculated Industries Construction Master ConcreteCalc Pro 4225 User manual
