Bticino 3489GSM User manual

3489GSM

Manual installer

Index

1 PREFACE 24

1 INTRODUCTION 26

1.1 PACKAGE CONTENT 26

1.2 TECHNICAL FEATURES 26

1.3 MECHANICAL FEATURES 27

1.4 LED 27

1.5 CONNECTORS PANEL 28

2 INSTALLATION 29

2.1 FIRSTPOWERON 29

2.2 OUTGOING CALL 30

2.3 INSERT THE PIN CODE 30

2.4 INSERT THE PUK CODE 31

2.5 ROAMING CALLS 31

2.6 BACK-UPBATTERY 33

2.6.1 REMOVE THE BACK-UP BATTERY 33

2.7 WALLMOUNT 34

3 REMOTE CONTROL VIA SMS 35

3.1 LIST OF AUTHORIZED USERS 35

3.1.1. LIST OF AUTHORIZED USERS: CONFIGURATION 36

3.1.2 LIST OF AUTHORIZED USERS: CONFIGURATION ACKNOWLEDGE MESSAGE 37

3.1.3 LIST OF AUTHORIZED USERS: CHECK THE CONFIGURATION 37

3.2 LOWBATTERY 37

3.2.1 LOW BATTERY: CONFIGURATION 38

3.2.2 LOW BATTERY: CONFIGURATION ACKNOWLEDGE MESSAGE 39

3.2.3 LOW BATTERY: CHECK THE CONFIGURATION 39

3.2.4 LOW BATTERY: WARNING MESSAGES 39

3.3 CONFIGURATION RESET 40

3.4 DEVICE REBOOT 40

3.5 INFORMATIONREQUEST 41

PREFACE

Inordertoguaranteeyoursafetyandacorrectfunctioning,besuretofollowthesesafetywarnings.Thewhole

set(withcablesincluded)mustbeinstalledinaplacelackingofordistantfrom:

• Dust,humidity,hightemperaturesanddirectexposuretosunlight.

• Heatirradiatingobjects,whichmaydamageyourdeviceorcauseanyotherproblem.

• Objectsproducingahighelectromagneticfield(Hi-Fispeakers,etc.).

• Corrosiveliquidsorchemicalsubstances.

ENVIRONMENTAL CONDITIONS

Environmenttemperature:from0°Cto+45°C Relativehumidity:from20to80%n.c.

Anysuddenchangeintemperatureandhumiditymustbeavoided.

CLEANING INFORMATION

Useasoftdryclothandavoidanysolventsorabrasivematerials.

SHOCKS OR VIBRATIONS

Cautionagainstshocksorvibrations.

BACKUP BATTERY

WARNING:thisdeviceissuppliedwithabackupbattery.

Thisbatterymaygetburnt,explodeorcauseseriousburnings.DONOTdisassemble,weld,burnorthrowthe

batteryintowater.Keepoutofchildren.Replaceonlywithasamemodelbatteryandreservetheoperation

onlytoqualifiedstaff.Theuseofadifferentbatterymaycausefirehazardorexplosions.Italianlawsconsider

batteriesasdangerousurbanwastethatmustbedisposedaccordingtothelawprovisionsinforce(ItalianDPR

915/82 and local provisions).

Thebackupbatteryisexcludedfromwarranty.

DECLARATION of CONFORMITY

We,BTicinoSpAregisteredofficeat:viaMessina38-20154Milano(Italy)declareunderoursoleresponsability

thattheproductwithnameBT-3489GSMType:ModemQuad-Band850/900/1800/1900MHz,Category:Device

fortheInformationTechnologysatisfiesthebasicrequirementofthebelowindicatedDirective:

- 1999/5/EC 9th March 1999, R&TTE (concerning radio equipment and telecommunication terminal

equipmentandtheacknowledgmentoftheirconformity)LawDecree9thMay2001,n.269,(G.U.n.156of

7-7-2001).

- Directive2009/125/ECOFof21October2009,ERP,establishingaframeworkforthesettingofecodesign

requirementsforenergy-relatedproducts.ECRegulationsn°278/2009andn°1275/2008

 AsindicatedinconformitywiththerequirementsoffollowingReferenceStandardsorofotherregulations

documents:

 EN301489-1 EN301489-7 EN301511 EN55022 EN55024

 EN62311 EN60950-1

SAFETY WARNINGS

Readtheseinstructionsandnormscarefullybeforepoweringthedevice.Violationofsuchnormsmaybeillegal

andcausehazardsituations.

Foranyofthedescribedsituationspleaserefertothespecificinstructionsandnorms.

Thedeviceisalowpowerradiotransmitterandreceiver.WhenitisON,itsendsandreceivesradiofrequency

(RF) signals.

3489GSM

Installer manual

Thedeviceproducesmagneticfields.Donotplaceitnexttomagneticsupportssuchasfloppydisks,tapes,etc.

Operatingyourdeviceclosetootherelectricalandelectronicequipment-suchasatelevision,phone,radioor

apersonalcomputer-maycauseinterferences.

INTERFERENCES

Thedevice,likeallotherwirelessdevices,issubjecttointerferencesthatmayreduceitsperformances.

ROAD SAFETY

Donotuseyourdevicewhiledriving.Incaseofuseoncars,youmustcheckthattheelectronicequipmentis

shieldedagainstRFsignals.Donotplacethedeviceintheairbagdeploymentarea.

AIRCRAFT SAFETY

Switch off your device when on board aircrafts by disconnecting the power supply and deactivating the

internalbackupbattery.UsingGSMdevicesonaircraftsisillegal.

HOSPITAL SAFETY

Do not use the device near health equipment, especially pacemakers and hearing aids, in order to avoid

potentialinterferences.Takecarewhenutilizingthedeviceinsidehospitalsandmedicalcentres,whichmake

useofequipmentthatcouldbesensitivetoexternalRFsignals.Switchitoffwhenuseisexpresslyforbidden.

EXPLOSIVE MATERIALS

Donotusethedeviceinrefuellingpoints,nearfuelorchemicals.Donotusethedevicewhereblastingisin

progress.Observerestrictionsandfollowanyspecificregulationorinstruction.

INSTRUCTIONS FOR USE

Donot usethe deviceindirectcontactwiththehumanbodyand donot touchtheantennaifnot strictly

necessary.

Use approved accessories only. Consult documentation regarding any possible device connected to the

device.Donotconnectincompatibleproducts.

INFORMATION FOR USERS

Accordingtothe2002/95/CE,2002/96/CEand2003/108/CEDirectives,relativetoreductionintheuseofhazardoussubstances

inelectricalandelectronicapparatus,aswellastodisposalofwastematerials.

Thesymbolofacrossedboxappliedontheapparatusoronitspackageindicatesthatattheendofitsusefullifethe

productmustbecollectedseparatelyfromotherwastematerials.

Theuser must thereforetaketheapparatuswhich hasreachedtheendofitsusefullifetoappropriateseparate

collection centres for electronic and electro-technical waste materials, or deliver it back to the reseller when

purchasingnewapparatusofanequivalenttype,givingonepieceinforonepieceout.

Suitable separate waste collection for then sending the cast-off apparatus for recycling, treatment and

environmentallyfriendlydisposal,contributestowardspreventinganypossiblenegativeeffectsontheenvironmentandon

healthandencouragesrecyclingofthematerialstheapparatusismadeupof.

Unauthorizeddisposaloftheproductbytheuserwillleadtopaymentoftheadministrativesanctionsinforceinthecountry

whereitisputonthemarket.

1 INTRODUCTION

GSM/PSTN interface simulates an analog linewhere

thetraditionalfixedlineisnotavailableorwhereitis

notconvenienttotakeit.

Thanks to GSM/PSTN interface an analog telephone

lineisalwaysreadyandyoucancontinuetouseyour

traditionalcommunicatorswithoutconnectingtothe

fixedline,saving the costs of the analog line.

1.1 PACKAGE CONTENT

• n.1GSM/PSTNinterface

• n.1Switchingpowersupply(IN:100-240Vac/50-

60Hz / 0.5A – OUT 12 Vdc / 1A)

• n.1GSMAntennawitha3meterscable

• n.1Phonecabletoconnectyourcommunicator(1.5meters)

• n.1Bracketforwallmounting

• n.2Capsforbracketfixing

• n.1User’sGuide

1.2 TECHNICAL FEATURES

• GSMModule:GSM/GPRSModemQuad-Band850/900/1800/1900MHz

• Outputpower:

 -Class4(2W)inGSMat850/900MHz

 -Class1(1W)inDCSat1800/1900MHz

• FXSVoiceInterface

• Off-hookACimpedance:600ohm

• On-hooklinevoltage:48VDC

• Off-hooklinepower:25mA

• Dialingtype:Tone(DTMF)

• Ringingvoltage:38VACrms-REN:3

• Voicecall

• OperatingTemperature:from0°Cto+45°C

• Ledindicators

• Back-upbattery

• CEMarkandRohscompliant

3489GSM

Installer manual

1.3 MECHANICAL FEATURES

• 2RJ11Connectors

• Plug-inSIMcard(1,8V-3Vcompatible)

• ExternalGSMantennaonSMA/fconnector

• Bracketforwallmounting

• Dimensions:115x80x45mm

1.4 LED

GSM/PSTNinterfacehas3ledsthatshowthedifferentstatusandsituations:

Activity

GSM

Status

LED STATUS DESCRIPTION

Status OFF Device turned OFF or roaming services

 ON DeviceONandsearchingfortheGSMNetwork

 SlowBlinking DeviceregisteredtotheGSMNetwork

 FastBlinking Activecommunication

GSM OFF GSMNetworkSearching,LowGSMSignalLevel,SIMcardnotpresent,PIN

not inserted

 Blinking GoodGSMSignalLevel

 ON VeryGoodGSMSignalLevel

Activity OFF Back-upBatteryNOTPresent(ornotconnected)

 ON Back-upBatteryCharging

 SlowBlinking DeviceispoweredbyBack-upBattery

 FastBlinking LowBattery

1.5 CONNECTORS PANEL

CONNECTOR DESCRIPTION

A PWR Powersupplyconnector

BUSB USB connector for upgrades

C TEL1/TEL2 RJ11FXSconnectorsforcommunicators

D Antenna SMA/fconnectorforexternalGSMantenna

ESIM SIM connector

F Switch Switchforthedevicepowero-on

3489GSM

Installer manual

2 INSTALLATION

For a correct installation, turn the device off and read the following instructions.

PWR

Power supply

RJ11

ANTENNA

SIM

USBTEL1 TEL2

Communicator

1. Connect the GSM antenna found in the package to the SMA connector.

In case the interface is installed in combination with an alarm system station, install

the antenna at least 1,5 meters from the alarm system station itself.

2. Insert the SIM Card into the SIM holder. Be sure the SIM is inserted in the correct way being

careful of the SIM corner, so that the golden contacts are placed downwards.

3. Connect the Communicator to one of the TEL1 / TEL2 connector present on the back side. The

2 connectors are connected together so there is no difference between the two ports.

4. Connect the power supply and turn GSM/PSTN interface on using the switch.

2.1 FIRST POWER ON

After few seconds of the power on, at the end of the self test, you can see one of the following

situations.

LED Regular situation PIN required Roaming / Virtual operator

Activity ON ON Blinking

GSM Blinking / ON 1 OFF Blinking

Status Blinking ON Blinking

1 GSM signal level.

Regular situation: CheckthegoodGSMsignallevelinordertocallandreceivethe

voicecall(GSMledONorBlinking).

PIN required: digitthePINcode,describedinthefollowingparagraphs.

Roaming / Virtual operator: enabletheRoamingcalls,describedinthefollowingparagraphs.

2.2 OUTGOING CALL

Hookoffthephone,waitforthedialtone,thendigitthephonenumber.

AfterthelastdigitGSM/PSTNinterfacewaitsfor5secondsbeforedialingthephonenumber;the

“#”hashbuttoninformsGSM/PSTNinterfacethatthephonenumberiscomplete,anditcangoon

withthecall.

2.3 INSERT THE PIN CODE

IftheprotectionPINcodeoftheSIMcardisenabledandthePINhasnotbeensetinthegateway,

the Status led is ON and the PIN code request is transmitted to the phone line (double beep

repeatedwithashortpause).

InsertthePINcodeusingthephonekeypad(setDTMFselection)connectedtotheTEL1orTEL2

ports:

1. Hookoffthephone,youhearthePINcoderequesttone.

2. EnterthePINCodeusingthephonekeypad(usingaDTMFphone)andconfirmbypressingthe

“#”(hash)button.

PIN code# (i.e. 0123#)

3. TocancelthewrongPINcode,hangupbeforesendingthe“#”(hash)button.

4. IfthePINcodeiscorrectyouwillheartheconfigurationtone(continuoustonerepeatedtwice).

5. HookonthephoneandwaitfordetectionoftheGSMnetwork.

6. IfthePINcodeiswrongyouwillhearthewrongconfigurationtone(singlelongtone).

ATTENTION: PIN and PUK codes are present on PIN-PUK card provided by GSM

Operator when you buy the SIM card. Please note that you have 3 possibilities to

enter the right PIN code. If insertion fails, you must insert the PUK code and a new

PIN code.

If you write a wrong PUK code 10 times, the SIM card will be blocked.

ThePINcodeisautomaticallystoredintoGSM/PSTNinterfaceanditwillbeusedwhennecessary.

IftheSIMcardisremovedorstolenthenyoumustnewlyinsertthePINcodemanually.

TodeletethePINcodefromdevicememory,enter#*99#codeusingthephonekeypadconnected

to TEL1 or TEL2 connector.

CheckthegoodlevelofGSMsignalandeventuallytrytoimproveitbyplacingtheantennaina

different position.

3489GSM

Installer manual

2.4 INSERT THE PUK CODE

TherequestforPUKcodeissignalledwithadifferentspecialtonewithrespecttothePINtone

request(doublebeeprepeatedwithnopause).

InsertthePUKcodeusingthephonekeypad(setDTMFselection)connectedtotheTEL1orTEL2

port:

1. Hookoffthephone,youhearthePUKcoderequesttone(doublebeepwithnopause).

2. EnterthePUKcodeusingthephonekeypad(usingaDTMFphone)andconfirmbypressing

the“#”(hash)button,followedbyanewPINcodewith4digits,thenpress“#”again.

PUK code#PIN code# (i.e. 12345678#1234#)

3. TocancelthewrongPUKcode,hangupbeforesendingthefirst“#”(hash)button.

4. If the PUK code is correct you will hear the configuration tone (continuous tone repeated

twice).

5. HookonthephoneandwaitfordetectiontotheGSMnetwork.

6. IfthePUKcodeiswrongyouwillhearthewrongconfigurationtone(singlelongtone).

2.5 ROAMING CALLS

InfactoryconfigurationtheGSM/PSTNinterfacedetectsautomaticallytheGSMoperator.Ifthe

deviceisinstalledneartheStateboundaries,itcoulddetectstheforeignGSMoperator,andthe

tariffcouldbehigherduringthevoiceconversations.

Toadvisetheuserofthisparticularsituation,ifinroamingphase,onthedeviceallthethreeleds

willblinksimultaneously,andtheoutgoingcallsareforbidden:theuserwillhearinthephonea

singlecontinuoustoneforfewseconds.

ThesamesituationcouldbepresentalsofarfromStateboundariesbutusingaSIMcardofVirtual

GSMOperator:inthiscasethetariffremainthesame.

Toenablethedeviceforoutgoingcallsinthesesituationsitisnecessaryinsertacodeusingthe

phonekeypad(setDTMFselection)connectedtotheTEL1orTEL2ports.

Table of contents

Other Bticino Security System manuals

Bticino

Bticino MYHOME SCREEN3,5 User manual

Bticino

Bticino HC4608 User manual

Bticino

Bticino Polyx Alarm 3485B User manual

Bticino

Bticino HC4601 User manual

Bticino

Bticino 367221 User manual

Bticino

Bticino 393014G User manual

Bticino

Bticino 391861 User manual

Bticino

Bticino 349416 User manual

Bticino

Bticino HC4608 User manual

Bticino

Bticino 348220 User manual

Bticino

Bticino 3500 User manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual