Brother WL-660 Series User manual

English

Laser Printer WL-660 Series for Windows®

Quick Setup Guide

First read this Quick Setup Guide to set up your printer and prepare your computer for the

printer.

CAUTION

This printer has been designed specially for Windows 3.1. It cannot work in a DOS

environment such as MS-DOS.

Action 1: Check the Supplied Items

After taking the printer out of the carton and removing the packing materials, make sure that

the following items are not damaged and none are missing:

• Printer • Multi-purpose sheet feeder

• Drum unit • Starter Toner cartridge

NOTE: This is a starter toner cartridge

—expected yield 1,000 pages.

TN-100 Replacement toner cartridge

—expected yield 3,000 pages

• 3.5” floppy disks for Windows®• User’s guide

• Quick setup guide (this guidebook)

NOTE

You will need to purchase an interface cable that matches the interface of your computer. If

you do not know what cable you need, consult your dealer or reseller.

The product names in this guidebook are trademarks or registered trade marks of each manufacturer. The specifications are subject to change without notice.

UL7394001 A Printed in Japan

English

Action 2: Install the Toner Cartridge/Drum Unit

1Unpack the drum unit and gently shake it

from side to side five or six times.

2Remove the protective parts, in order, as

shown in the illustration.

CAUTION

Do not expose the drum unit to light for

longer than a few minutes, as this will

damage the drum.

3Open the top cover. Open the drum cover

by pushing the two blue tabs in toward the

center of the unit and lifting the cover

toward you.

4Install the drum unit into the printer.

Make sure that you grasp the ▲marks.

English

5Unpack the toner cartridge and gently rock

it from side to side well before installing.

( ①)

Then, remove the protective parts. ( ②)

CAUTION

DO NOT MOVE THE SHUTTER LEVER

UNTIL THE CARTRIDGE IS

INSTALLED.

6Install the toner cartridge into the drum

unit. Make sure that the ▲marks are

aligned.

7Gently pull the blue shutter lever on the

toner cartridge forward until the red arrows

are aligned.

8Close the drum cover ( ①) and push gently

until it clicks into place.

Close the top cover. ( ②)

See “CHAPTER 5 MAINTENANCE” in

the User’s Guide for more information

about replacement of the toner cartridge.

English

Action 3: Load Paper into Your Printer

1Install the paper support into the multi-

purpose sheet feeder. ( ①)

Install the sheet feeder into the printer.

( ②)

2Open the multi-purpose sheet feeder cover.

3Load paper into the multi-purpose sheet

feeder.

NOTE

The feeder can hold up to 200 sheets of

plain paper or up to 10 envelopes.

Excessive sheets may cause paper jams.

Make sure that the paper is stacked below

the ▲mark.

4Move the paper guide to fit the paper width.

English

5Close the multi-purpose sheet feeder cover.

6Open the output tray. ( ①)

Extend the paper support wire. ( ②)

The printer can handle paper that has the following specifications:

Paper Type Paper Size Paper Weight Sheet

Feeder Manual

Cut sheet A4, Letter, Legal, B5, A5,

3”x5”, Executive, Custom size

(70-216 x 127-356 mm

2.75”-8.5” x 5”-14”)

●●

Envelopes DL, C5, COM-10, Monarch 60-135 g/m2●●

Organizer Day-Timer®J, K, L, M

70-216 x 127-356 mm

2.75”-8.5” x 5”-14”

(16-36 lb.) ●●

Labels

Transparencies 70 - 216 x 127-356 mm

2.75”-8.5” x 5”-14” ●

See “CHAPTER 2 PAPER HANDLING” in the User’s Guide for more information.

English

Action 4: Connect Your Printer and Computer

You must connect the printer to your computer using an interface cable. A parallel cable is

used for this connection.

1Make sure that the power cord is unplugged

before connecting or disconnecting the

interface cable.

Also, make sure that the computer is turned

off.

NOTE

The shape of the power cord varies

according to the country of destination.

2Connect the parallel interface cable to the

connector of the printer. ( ①)

Secure the connection with the wire clips.

( ②)

Connect the interface cable to the printer

port of the computer.

NOTE

For the location of your computer’s parallel

printer port, see the User’s Guide of your

computer.

English

Action 5: Plug in the Power Cord and Turn on Your Printer

1Plug the power cord into the AC power

outlet.

NOTE

This printer has no power switch. The

printer has a sleep mode that allows the

printer to automatically reduce power

consumption when not in use.

2Make sure that the READY lamp is ON

after the printer has warmed up (about 60

seconds).

English

Action 6: Set up the Printer Driver and Fonts for Windows 3.1

Check the following system requirements to run the Setup program and operate the printer

correctly:

• IBM PC or compatible with 80486 SX or higher microprocessor

• Parallel interface (or printer port)

• 4 MB or more of memory

• 10 MB of space available on your hard disk for the printer driver and all fonts

• Microsoft Windows 3.1/3.11

CAUTION

This printer has been designed specially for Windows 3.1. It cannot work in a DOS

environment such as MS-DOS.

You need to set up this printer by installing the printer driver and TrueType-compatible fonts

into Windows 3.1. Because the supplied printer driver and fonts are compressed on the disk,

be sure to use the supplied Setup program to install them as follows:

1. Start Windows 3.1.

2. Insert the supplied disk into your floppy disk drive A (or drive B).

3. Choose Run from the File menu in the Program Manager.

4. Type A:\SETUP (or B:\SETUP for drive B) in the Command Line box.

5. Choose the OK button or press the Enter key.

6. Follow the instructions that appear on the display monitor.

7. When the installation is complete, remove the disk from the drive.

English

NOTE

• The Setup program automatically updates Windows SYSTEM.INI file by adding

DEVICE=bi-di.386 under the [386Enh] section. If any bi-directional parallel

communications device driver has been previously installed, it will be deactivated by this

new driver. If you want to use the previous driver, you should first install this driver, then

re-install the previous one, which will make this driver inactive.

• The Setup program makes the installed printer driver default.

• The Setup program automatically sets the printer port to the parallel interface, LPT1.

• The Setup program adds changes to the SYSTEM.INI file. It is necessary to restart

Windows so that the changes become effective and the installed bi-directional parallel

communications device driver can take effect.

English

Action 7: Set Print Options of Your Printer

Before you print documents, set the print options of your printer as follows:

1. Make sure that Windows is restarted immediately after running the Setup program.

2. Open Control Panel in the Main group window.

3. Open Printers in the Control Panel window.

4. Make sure that your printer has been selected or made default.

5. Choose Setup to open the Setup dialog box of your printer.

For more information about print options, choose Help or press the F1 key while you see

them in the dialog box.

6. Click any icon button on top of the Setup dialog box to open the setting menu and choose

print options.

7. Choose OK to close the dialog box to return to the Printers dialog box.

8. Choose Close to return to Control Panel.

9. Close Control Panel.

Your selected print options remain effective until you change them from within the Printers

dialog box on the Control Panel or the Print Setup dialog box of your application software.

Other manuals for WL-660 Series

Table of contents

Other Brother Printer manuals

Brother

Brother HL-L3290CDW User manual

Brother

Brother HL-L3210CW User manual

Brother

Brother DCP-T520W User manual

Brother

Brother HL-L5000D User manual

Brother

Brother HL-L8260CDN User manual

Brother

Brother HL-1650 User manual

Brother

Brother HL-2070N User manual

Brother

Brother RJ-2035B User manual

Brother

Brother GT-541 User manual

Brother

Brother MFC-J5335DW User manual

Brother

Brother m-PRINT MW-100 User manual

Brother

Brother HL-2230 User manual

Brother

Brother HL-2070N Installation instructions

Brother

Brother HL-2220 User manual

Brother

Brother 7050N - HL B/W Laser Printer User manual

Brother

Brother HL-4000 Series User manual

Brother

Brother HL-L2380DW User manual

Brother

Brother SP-1 User manual

Brother

Brother HL-5240 User manual

Brother

Brother MPRINT MW-145MFi User manual

Brother

Brother DCP-L3515CDW User manual

Brother

Brother HL-1020 User manual

Brother

Brother RuggedJet RJ-4030 User manual

Brother

Brother HL-7050 Series User manual

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Evolis

Evolis Elypso user guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Ricoh

Ricoh MD-P1 Service manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide