Brother HL-660 Series User manual

English

Brother Laser Printer HL-660 Series Quick Setup Guide

Read this guidebook first to set up your printer.

Action 1: Getting Started

Check the Supplied Items

After taking the printer out of the carton and removing the packing materials, make sure that

the following items are not damaged and none are missing:

• Printer • Multi-purpose sheet feeder

• Drum unit • Starter Toner cartridge

NOTE: This is a starter toner cartridge

– expected yield 1,000 pages

TN-100 Replacement toner cartridge

– expected yield 3,000 pages

• 3.5” floppy disks for DOS/Windows®

• Software setup guide

• Quick setup guide (this guidebook)

• User’s guide

• Plastic Bag

NOTE

You will need to purchase an interface cable that matches the interface of your computer. If

you do not know what cable you need, consult your dealer or reseller.

The product names in this guidebook are trademarks or registered trademarks of each manufacturer. The specifications are subject to change without notice.

Japan

English

Action 2: Install the Toner Cartridge / Drum Unit

1Unpack the drum unit and gently shake it

from side to side five or six times.

2Remove the protective parts, in order, as

shown in the illustration.

NOTE

Do not expose the drum unit to light for

longer than a few minutes, as this will

damage the drum.

3Open the top cover. Open the drum cover

by pushing the two blue tabs in toward the

center of the unit and lifting the cover

toward you.

4Install the drum unit into the printer.

Make sure that you gasp the ▲marks.

English

5Unpack the toner cartridge and gently rock

it from side to side well before installing.

( ①)

Then, remove the protective parts.( ②)

CAUTION

DO NOT MOVE THE SHUTTER LEVER

UNTIL THE CARTRIDGE IS

INSTALLED.

6Install the toner cartridge into the drum

unit. Make sure that the ▲marks are

aligned.

7Gently pull the blue shutter lever on the

toner cartridge forward until the red arrows

are aligned.

8Close the drum cover ( ①) and push gently

until it clicks into place.

Close the top cover. ( ②)

See “CHAPTER 5 MAINTENANCE” in

the User’s Guide for more information

about replacement of the toner cartridge.

English

Action 3: Load Paper into Your Printer

1Install the paper support into the multi-

purpose sheet feeder. (①)

Install the sheet feeder into the printer. (②)

2Open the multi-purpose sheet feeder cover.

3Load paper into the multi-purpose sheet

feeder.

NOTE

The feeder can hold up to 200 sheets of

plain paper or up to 10 envelopes.

Excessive sheets may cause paper jams.

Make sure that the paper is stacked below

the ▲mark.

4Move the paper guide to fit the paper width.

English

5Close the multi-purpose sheet feeder cover.

6Open the output tray. ( ①)

Extend the paper support wire. ( ②)

The printer can handle paper that has the following specifications.

Paper Type Paper Size Paper Weight Sheet

Feeder Manual

Cut sheet A4, Letter, Legal, B5, A5,

3”x5”, Executive, Custom size

(70-216 x 127-356 mm

2.75”-8.5” x 5”-14” inches)

60-135 g/m2

(16-36 lbs) ●●

Envelopes DL, C5, COM-10, Monarch ●●

Organizer Day-Timer®, J,K,L M

70-216 x 127-356mm

2.75”-8.5” x 5”-14” inches

●●

Labels 70 - 216 x 127-356 mm ●

Transparencies 2.75”-8.5” x 5”-14” inches ●

See “CHAPTER 2 PAPER HANDLING” in the User’s Guide for more information.

English

Action 4: Connect Your Printer and Computer

You must connect the printer to your computer using an interface cable. A parallel cable is

used for this connection.

1Make sure that the power cord is unplugged

before connecting or disconnecting the

interface cable.

Also, make sure that the computer is turned

off.

NOTE

The shape of the power cord varies

according to the country of destination.

2Connect the parallel interface cable to the

parallel interface port of the printer. ( ①)

Secure the connection with the wire clips.

(②)

Connect the interface cable to the printer

port of the computer.

NOTE

HL-660 series printer can also operate with an AppleTalk interface by installing the optional

serial interface board. In some countries it is installed as standard. For more information, see

“CHAPTER 4 OPTIONS” in the User’s Guide.

For the location of your computer’s parallel printer port, see the User’s Guide of your

computer. Next, skip to the section “Turning On Your Printer”. After printing a test sample

page, you will then be ready to prepare your computer’s software. For setting up the printer

software, see the Software Setup Guide.

English

Action 5: Plug in and Turn on Your Printer

1Plug the power cord into the AC power

outlet.

NOTE

This printer has no power switch. The

printer has a sleep mode which allows the

printer to automatically reduce power

consumption when not in use.

2Make sure that the READY lamp is ON

after the printer has warmed up (about 60

seconds).

Printing a Test Sample Page

We recommend that you print a test page. Refer to the instructions below.

1Depress the TEST (FF/CONT) switch until

all lamps are turned ON. The printer starts

printing a test sample page.

The printed page shows the basic control

panel operations.

NOTE

If the printer does not print a test sample page exactly, see “CHAPTER 6 Troubleshooting - Q

& A” of the User’s Guide. If after reviewing the information in the User’s Guide, your printer

still cannot print the test sample page correctly, consult your dealer or reseller.

English

Shipment of the Printer

If for any reason you must ship your Printer, carefully package the

Printer to avoid any damage during transit. It is recommended that you

save and use the original packaging. The Printer should also be

adequately insured with the carrier.

Warning

When shipping the Printer, the DRUM UNIT assembly including the

TONER CARTRIDGE must be removed from the Printer and place it

in the plastic bag. Failure to remove it and place it in the plastic bag

during shipping, will cause severe damage to the Printer and will

VOID THE WARRANTY.

1 Remove the drum unit. 2 Place it in the plastic bag and fold

the plastic bag under the drum unit.

3 Wrap it in the corrugated

cardboard. 4 Re-pack the printer.

Other manuals for HL-660 Series

This manual suits for next models

Table of contents

Other Brother Printer manuals

Brother

Brother DCP-T220 User manual

Brother

Brother MPrint MW-140BT User manual

Brother

Brother MFC-8530DN User manual

Brother

Brother HL-L5200DW User manual

Brother

Brother MFC-8880DN User manual

Brother

Brother DCP-B7500D User manual

Brother

Brother HL-1470N User manual

Brother

Brother HL-B2000D User manual

Brother

Brother MFC-J491DW User manual

Brother

Brother m-PRINT MW-120 User manual

Brother

Brother HL-3140CW User manual

Brother

Brother HL 1850 - B/W Laser Printer User manual

Brother

Brother MFC-J280W User manual

Brother

Brother MFC-L2771DW User manual

Brother

Brother HL-1070 User manual

Brother

Brother MFC7840CW Instruction Manual

Brother

Brother MFC-J3530DW Operating manual

Brother

Brother P-TOUCH PT-2100 User manual

Brother

Brother DCP-L3528CDW User manual

Brother

Brother HL-5240L User manual

Brother

Brother HL-2460 Series User manual

Brother

Brother DX-2000 User manual

Brother

Brother GT-3 Series User manual

Brother

Brother HL-1870N Assembly instructions

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Evolis

Evolis Elypso user guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Ricoh

Ricoh MD-P1 Service manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide