Bradley LUCENT Series User manual

Installation

P.O. Box 309

Menomonee Falls, WI 53052 USA

800 BRADLEY (800 272 3539)

+1 262 251 6000

bradleycorp.com

AD3-LUCENT_Install Rev. B

Page 1 of 23 11/8/2023

Euro Style Restroom Partitions

Glass – LUCENT Series

Read the instructions in this manual before

beginning installation. Save these instructions

and refer to them for inspection, maintenance,

and troubleshooting information.

For questions regarding the operation, installation or maintenance of this product, visit bradleycorp.com

or call 800.BRADLEY (800.272.3539).

Product warranties and parts information may also be found under “Resources” on our website at bradleycorp.com.

Table of Contents

Safety Information ...........................2

Supplies Required ...........................2

Measuring & Marking Drill Holes ................3

Marking Drill Holes for Floor Pivots..............3

Installing the Floor Pivots .....................4

Attaching the Retaining Brackets ...............5

Installing & Securing the Dividing Panel ..........6

Installing the Dividing Panel ...................7

Mounting the Headrail ........................8

Assembling Panels to Pilasters Using L-Brackets ..9

Installing the Doors .........................10

Hydraulic Hinge Guide.......................10

Aligning the System.........................11

Final Assembly.............................12

Mounting the Door Latch.....................13

Latch Selection Guide .......................13

Mounting Hooks & Bumpers ..................20

Assembling the Self-Closing, Hydraulic Hinge

Assembly .................................20

Fraction-Decimal Conversion Chart ............23

Euro Style Restroom Partitions, Glass — LUCENT Series Installation

11/8/2023 Bradley • AD3-LUCENT_Install Rev. B

Safety Information

Warning

Before beginning installation, make sure that the wall and floor backing are adequate to support the secure mounting of the

toilet compartment units.

Partitions are extremely heavy and may require more than one person to position and install.

Failure to comply with these instructions may result in personal injury and/or property damage and will void the partition

warranty.

Caution

Personal protective equipment (PPE) is required during the installation and maintenance of this product.

Notice

Make sure all floors and walls are clean and smooth. Remove loose impediments, such as protruding nails and other debris

which could affect installation.

Carefully remove components from skid, do not drag.

Important

Review your partition layout drawings and verify the number of stalls and components before beginning installation.

Read this installation manual completely to ensure proper installation, then file it with the owner or maintenance department.

This installation manual provides instruction for the assembly of normal partition configurations and standard components.

Non-standard configurations or components including but not limited to curved or angled walls, notched walls, partial walls,

oversized panels, or modified hardware may not be covered in this manual. Compliance and conformity to local codes and

ordinances is the responsibility of the installer.

Separate parts from packaging and make sure all parts are accounted for before discarding packaging material. If any parts are

missing, do not begin installation until you obtain the missing parts.

Supplies Required

• Chalk line and pencil

• 4D laser level

• Power drill or screw gun with drill bit extension

• Cordless screwdriver

• Power rivet gun

• Metric tape measure (recommend a wood folding metric ruler)

• Standard hand tools

• Metric drill bits as needed

• Torque wrench and Torx bit 30 with bore

• Metric Allen wrench set

• Countersunk rosette key or small snap ring wrench

• HB45 construction adhesive or equal

• Step ladder

• Fast drying epoxy

• Clamps

Installation Euro Style Restroom Partitions, Glass — LUCENT Series

Bradley • AD3-LUCENT_Install Rev. B 11/8/2023

When installing the partition components, consult the

applicable Bradley Partition submittal drawing speciﬁc to

this job for compartment layout dimensions.

Refer to the drawing for the measurements for exact

drilling points for the holes in the ﬂoor.

Refer to the drawing for the measurements for exact

drilling points for the holes in the ﬂoor and dividing panel

supports.

Optional - Use Bradley provided (on loan) drilling guide to

aid in drilling holes in ﬂoor.

1Measuring & Marking Drill Holes

2Marking Drill Holes for Floor Pivots

Using the hinge oor pivot as a template, trace the

drilling hole locations onto the center line of the front

panel on the oor.

Trace the drilling holes for the oor pivot and the

dividing panel support onto the dividing panel

centerline on the oor.

On the traced centerlines, use a wet drill with an

18mm core bit to drill 30mm into the oor.

From the accompanying production drawing note

the centerline dimensions and the dimension line

of the front wall. Transfer these measurements to

the oor. In some cases, a oor drill guide will be

provided.

Account for gaps, pilaster width, and door width.

Exact dimensions of ﬂoor drillings is crucial.

Centerline of lower hinge assembly hole in ﬂoor is

83mm from edge of door on the hinge side.

Panel support ﬂoor anchor is 113mm center line

recessed in from centerline front pilaster. Conﬁrm

before drilling hole.

Euro Style Restroom Partitions, Glass — LUCENT Series Installation

11/8/2023 Bradley • AD3-LUCENT_Install Rev. B

3Installing the Floor Pivots

Verify all dust and water has been removed from the

drilled holes. Insert fast-drying, epoxy-based adhesive

into the holes.

Place the oor pivot into the glue until the large collar

plate is pressed rmly against the oor. Verify the oor

pivot is vertically straight.

Wear gloves and use Acetone to quickly and carefully

remove any excess glue before the glue cures.

After the lower portion of the oor pivot/support is

set and the glue has hardened, you can assemble the

upper components to the oor units. For lower door

hinge units, thread the male threaded post into the

lower unit, assemble the ball bearing washer next,

metal washer next, and nally the thick brass bushing

onto the oor unit, in that order. Thread the post out

by one full turn so door hinge does not rub against

base.

For the regular support units, thread the male

threaded post into the lower unit, followed by the

large silver bushing.

It is normal for some excess glue to seep out from

under the plate.

Optional-thread Bradley provided (on loan) target level

to aid installing lower ﬂoor support perfectly level.

Verify the setscrew is accessible to allow for height

adjustment.

Depending on the room and ﬂoor temperature, the

glue may cure quickly. If glue dries before the excess

can be removed, you may carefully chip away the

excess glue using a chisel.

It is normal for some excess glue to seep out from

under the plate.

Unthread upper collar from the oor support.

Installation Euro Style Restroom Partitions, Glass — LUCENT Series

Bradley • AD3-LUCENT_Install Rev. B 11/8/2023

4Attaching the Retaining Brackets

Mark the centerline hole locations on existing back and

side walls for the retaining brackets that support the

dividing panels. Use a 4D laser level and begin with the

lowest bracket. These dimensions are appropriate for

standard height panels.

• Lower bracket 67mm from the oor.

• Middle bracket 1050mm from oor

• Upper bracket 1900mm from oor

Be aware of your surroundings and avoid electrical wires

and pipes.

Drill the marked hole locations on existing back and

side walls using an 8 mm drill bit, and then secure the

retaining brackets in place using 8 mm x 51 mm wall

anchors and 5.5 mm x 60 mm countersunk screws.

Use a level to make sure the brackets are vertical.

Place the angled bracket into the lower retaining

bracket as shown. The angled bracket will support the

dividing panel and prevent it from slipping.

Euro Style Restroom Partitions, Glass — LUCENT Series Installation

11/8/2023 Bradley • AD3-LUCENT_Install Rev. B

5Installing & Securing the Dividing Panel

Assemble the lower part of the support bracket into

the two holes found along the lower part of the front

of the dividing panel. This lower support bracket has a

large round opening that goes over the oor support,

with four set screws for nal adjustment. Loosen all

four set screws on the lower hinge assembly so the

inner points are completely out of the way of the oor

pivot.

Assemble the base to the glass by inserting the larger

female threaded posts covered with grey plastic

brushing into the holes in the glass. Face the screw

heads away from the front for aesthetic purposes.

Thread the smaller portion of the bracket with the (2)

M6 x 25mm screws through the plate into the female

threads. Tighten to the glass.

Repeat steps (ref above) for the upper supports.

Upper supports are similar to the lower supports

with the exception that the top has a small female

threaded opening.

Verify the gray nylon heads are fully inserted into the

partition glass.

Installation Euro Style Restroom Partitions, Glass — LUCENT Series

Bradley • AD3-LUCENT_Install Rev. B 11/8/2023

Carefully slide the wooden block away from the

dividing panel until the support leg can be set onto

the oor pivot.

Set the dividing panel onto the support.

6Installing the Dividing Panel

Insert the rear of the dividing panel into the retaining

brackets mounted on the wall, and then place a

50mm wood block and shins under the front of the

panel for support.

Use a 4D laser level to align the panel perpendicular

to the wall.

Makes sure panel is ush and level.

Tighten the retaining brackets down onto the panel to

secure it in place.

NOTICE! This is a vise-type bracket. No not overtighten!

Euro Style Restroom Partitions, Glass — LUCENT Series Installation

11/8/2023 Bradley • AD3-LUCENT_Install Rev. B

7Mounting the Headrail

Mark the centerline for the dividing panel onto the headrail.

Drill a hole on top of the headrail and countersink this hole in

the center of the headrail width using a 8.5mm drill bit.

Place the headrail onto the upper dividing wall holder and

secure using M8x25mm screws (screw threads have already

been prepared).

Adjust the headrail horizontally and secure the wall connector

to the wall using 6mmx30wall anchors and 5mmx38mm

countersunk screws.

Cover the round flange with square finish cover, secure with

glue to keep in place.

No cutting of the headrail should be necessary. The headrail

should already by cut to the correct length. Check for speciﬁc

location labels. Use the dividing panels as a guide.

Slide square ﬁnished cover over headrail, then assemble round

threaded adjusting ﬂange on end of headrail.

Center of the headrail equals the centerline of the front wall

plus 113mm.

Installation Euro Style Restroom Partitions, Glass — LUCENT Series

Bradley • AD3-LUCENT_Install Rev. B 11/8/2023

8Assembling Panels to Pilasters Using L-Brackets

Place the black nylon sides of the L-brackets against

the glass holes on the dividing panel. Do this on both

sides of the glass.

Secure the L-brackets together using M6x16mm

flathead screws and flat nuts.

Verify the panels and pilasters are level and flush.

Attach the pilasters to the end panels using the

L-brackets, countersunk 4 pin rosettes (facing the

outside of the stall), and M6x16mm screws.

Verify there is an approximate gap of 3mm between

the pilaster and panel.

Place L-brackets at the top, middle, and bottom of

the panel.

Euro Style Restroom Partitions, Glass — LUCENT Series Installation

11/8/2023 Bradley • AD3-LUCENT_Install Rev. B

9Installing the Doors

Adjust floor clearance and level the door. Tighten the

set screw on back of the reach over bracket, into

back of head rail to secure upper assembly, using a

3mm Allen wrench.

This will prevent the doors from falling out of adjustment.

Assemble upper and lower hinge assembly to door

similar to instructions on page 6. The upper hinge

assembly will have a hinge post protruding through

the top of the hinge bracket. Face screws inward for

aesthetic purposes.

Select the proper upper hinge assembly from the guide

shown on next page.

Hydraulic Hinge Guide for Self Closing Doors

BRO0540108

BRO0540107

Front

Front Front

Front

Headrail

Door

With the head rail in place, lower door in lower floor

pivot. This floor pivot should be complete with the

base, ball bearing disk, washer, and brass grommet.

Secure upper hinge assembly by carefully lowering

the upper reach over bracket over the head rail and

capture the upper hinge pin in the hole of the reach

over bracket. Make sure plastic grommet is in place

around pin.

Table of contents

Other Bradley Bathroom Fixture manuals

Bradley

Bradley S19-110BF User manual

Bradley

Bradley Express SS Series User manual

Bradley

Bradley WS-1X-HN User manual

Bradley

Bradley Terreon Classic WF2500 Series User manual

Bradley

Bradley S19274HWR User manual

Bradley

Bradley 5600 Series User manual

Bradley

Bradley Express EXD-3/WHTAS User manual

Bradley

Bradley TouchTime 1C User manual

Bradley

Bradley S19-130BF User manual

Bradley

Bradley Terrazzo WF2613 User manual

Bradley

Bradley S19-280D User manual

Bradley

Bradley S19-310 User manual

Bradley

Bradley S19-130SS User manual

Bradley

Bradley Express SS Series User manual

Bradley

Bradley S19-310SS User manual

Bradley

Bradley Express SS Series User manual

Bradley

Bradley S19-130BF User manual

Bradley

Bradley S19-310AC User manual

Bradley

Bradley S19-270HD User manual

Bradley

Bradley Bradmar 400 Series User manual

Bradley

Bradley HSC79 User manual

Bradley

Bradley SN2005/TT User manual

Bradley

Bradley Advocate AV Series User manual

Bradley

Bradley S19-315FPBF User manual

Popular Bathroom Fixture manuals by other brands

DURAVIT

DURAVIT C.1 C15240 0090 Instructions for mounting and use

Heatstore

Heatstore HSTRL500WTN Installation and operating instructions

Sunshower

Sunshower PURE SOLO manual

Delabie

Delabie Delabie Sporting 714700 manual

Kohler

Kohler K-13056 Homeowner's guide

ESS

ESS Container TCL-11 installation manual

Mustee

Mustee 22C installation instructions

VITRA

VITRA V-Flow manual

baliv

baliv DUK-80.30 T manual

Malmet

Malmet B105BT Operation, maintenance and installation manual

bathstore

bathstore Transition H1690MM Installation, Care & Adjustment Instructions

BELLOSTA

BELLOSTA Edward 0800/M Installation instruction

baliv

baliv DU-5160 manual

Franke

Franke PRTR0006 Installation and operating instructions

Gessi

Gessi RILIEVO 59011 manual

noken

noken VITAE 100188525-N299998810 manual

Allen + Roth

Allen + Roth 1142VA-30-201 manual

Britex

Britex HBDA installation guide