Bosch Plena PLE-1CS Reference guide

Plena Call Station

Quick Reference Card

PLE-1CS

en

Guide de Référence Rapide

PLE-1CSfr

Kurzanleitung

PLE-1CS

de

Beknopte Handleiding

PLE-1CS

nl

Guía de Referencia Rápida

PLE-1CS

es

Guida Rapida

PLE-1CS

it

Quick Reference Card

PLE-1CS

zh

Bosch Security Systems | 2007-10 | PLE-2MA120-EU, PLE-2MA240-EU en

Plena Mixer Amplifier | Installation and User Instructions | Connections and settings en | 16

4.1.2 Priority microphone (input 1)

The priority microphone (or a generic call station) that

can be used with push to talk (PTT) should be

connected to “microphone/line 1 input”. The PTT

mode can be activated by setting the DIP switch (4) at

the rear of the unit. Microphone/line 1 input has

priority over all other microphone/line inputs.

If, however, the “Tel. emergency/100V input” receives a

signal, all inputs including microphone/line 1 input will

be overruled.

The microphone/line 1 input has two connectors wired

in parallel:

• an XLR connector (for a 3 pole microphone), and

• a Euro style pluggable screw terminal connector.

The Euro style pluggable screw terminal connector has

a trigger input, which can be used in combination with

the Euro and XLR connector.

The priority microphone can be connected to the

microphone/line 1 input as follows:

• XLR connector only. See figure 4.2.

• XLR connector with trigger. See figure 4.3.

• Euro connector with trigger. See figure 4.4.

• Euro connector only (without trigger).

Set the DIP switch settings next to the XLR connector

for microphone/line 1, as required. See section 4.3.

Note

If a microphone is connected to both the

XLR connector and the Euro connector for the

microphone/line 1 input, the input signals will be

added together.

Note

When connecting an unbalanced line level

(200 mV) signal to the microphone/line input,

connect it as follows: Signal to pin 2, pin 1 and

pin 3 to ground.

figure 4.2: XLR connector only

figure 4.3: XLR connector with trigger

figure 4.4: Euro connector with trigger

Installation/configuration notes

3

S1

S2S3

5

4

2

1

1 2 3 4 5

Circuit diagram

Parts included

Quantit

y

Component

1PLE-1CS PLENA All Call Call Station

Technical specifications

Electrical

Phantom power supply

Voltage range 12 to 48 V

Current consumption <8 mA

Performance

Sensitivity 0.7 mV @ 85 dB SPL (2 mV/Pa)

Maximum input sound level 110 dB SPL

Distortion <0.6% (maximum input)

Input noise level (equiv.) 28 dB SPLA (S/N 66 dBA ref. 1 Pa)

Frequency response 100 Hz to 16 kHz

Output impedance 200 ohm

Mechanical

Base dimensions (H x W x D) 40 x 100 x 235 mm

(1.57 x 3.97 x 9.25 in)

Weight Approx. 1 kg (2.2 lb)

Color Charcoal with silver

Stem length with mic. 390 mm (15.35 in)

Cable length 2 m (6.56 ft)

Environmental

Operating temperature -10 ºC to +45 ºC (14 ºF to +113 ºF)

Storage temperature -40 ºC to +70 ºC (-40 ºF to

+158 ºF)

Relative humidity <95%

Ordering information

PLE‑1CS Plena All‑Call Call Station

All-zone call station with 2 m cable and lockable Euro

style connector.

Order number PLE-1CS

2 | PLE‑1CS Plena All‑Call Call Station

Table of contents

Other Bosch Security System manuals

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual