BlueTrek X3 User manual
User Manual
X3
2
“Vol -”button
“Talk” button
“Vol +”button
English
1 I BLUETREK X3
Before using your headset for the first time
-You must charge it continuously for about 4 hours, until the red indicator light turns off.
Please refer to the “Charging the BLUETREK® X3®”section of this manual.
-Pair the headset with a mobile phone. Please refer to the “Pairing the BLUETREK® X3”
section of this manual.
Introduction
The BLUETREK® X3 headset is a wireless headset based on the Bluetooth® technology. It com-
plies with Bluetooth® 2.0 protocol, supporting Headset and Hands-free profile.
The BLUETREK® X3 headset has 3 buttons:
·“TALK” button (main button)
·“Vol +”button
·“Vol -”button
English
BLUETREK X3 I 2
Charging the BLUETREK® X3
Please connect the charger to the headset and to the main. During the charge, the
indicator light is red.The indicator light will turn off when the charge is complete.
During subsequent charges, the charging should take approximately 3 hours.
When you hear a low-tone beep in your headset at regular intervals, and the indica-
tor light flashes in red, your headset needs to be recharged.
English
3 I BLUETREK X3
Important:
• If your headset is fully charged, the red indicator light will not turn on when plugging into
the charger.
• To maximize battery lifetime, it is recommended to recharge your headset to full capacity
only when the battery is low, since a battery has a lifetime of about 500 charging cycles.
• If you leave your headset battery empty for an extended period of time, it could excessively
discharge the battery. In this case, charge your headset for 2 hours or more until the battery
recovers and recharges completely.When you first charge the headset after prolonged stor-
age, it may take few minutes for the red indicator light to turn on.
• Do not charge your headset for more than 10 hours.
• The use of any other charger will automatically suspend the warranty. It is strictly forbidden
and can be very dangerous.
English
BLUETREK X3 I 4
Switching the BLUETREK® X3 ON and OFF
Switching BLUETREK® X3 ON
When your headset is off, press and hold the TALK button for about 3 seconds until the blue
indicator light is on. A beep (2 tones) can be heard in the speaker.
Release the TALK button.
Switching BLUETREK® X3 OFF
When your headset is on, press and hold the TALK button for about 7 seconds until the red
indicator light is on. A beep (2 tones) can be heard in the speaker then release the TALK
button.
Pairing the BLUETREK® X3
Before using the BLUETREK® X3 headset, you must pair it with your
Bluetooth® mobile phone.
Pairing is the process of linking 2 Bluetooth® devices, so that they
can communicate.
To initiate pairing:
Place the BLUETREK® X3 and your mobile phone within 0.3
meter (1 foot) from each other.
Switch on your phone and select its Bluetooth® discover mode
(refer to the Bluetooth® mobile phone user manual).
1
2
Connect
Assign short name
Set as unauthorised
Delete
Select Cancel
“0000”
BLUETREK X3 BLUETREK X3
“Talk” button
BLUETREKX3 BLUETREKX3
English
5 I BLUETREK X3
When the BLUETREK® X3 is switched off, press and hold
the TALK button for about 7 seconds until the indicator light
flashes red and blue alternately. And a sound can be heard
in the speaker.
3
If you haven’t started the discovery mode within 5 minutes, the headset will go to the standby
mode. You must then switch off your headset and start the pairing again.
If pairing was successful, the indicator light will switch to blue and flashes slowly.
The headset will connect automatically to the mobile phone.
Once the mobile phone detects the headset, a“BLUETREK X3”message will be displayed.
Follow the phone instructions to accept the pairing.The PIN code (or passkey) is 0000, then
press“yes”or“ok”.
For some phones, you may need to select“Connect”.
4
5
English
BLUETREK X3 I 6
Making a call
Mobile phone with voice recognition
• Make sure the voice recognition function on your mobile is activated and your voice tags
have been recorded with the phone.To enter these, please refer to your phone’s manual
• When there is no incoming or active call, press once on the TALK button
• Wait for the audio signal sent by the mobile phone (generally a short tone).
• Speak the name of person you wish to call.
Mobile without voice recognition
• Make sure both the headset and the mobile phone are ON and in stand-by mode.
• Dial the number on the phone keypad, after approximately 2 seconds the audio connection
will be established.
Answering a call
When the headset rings, press once on the TALK button to take the call.
Ending a call
Press once on the TALK button to end an active call.
This function may not be available on some phones, please refer to the trouble shooting
frequent asked questions in our website: www.bluetrek.com. to find out more.
English
7 I BLUETREK X3
Adjusting the volume
To increase the volume during an active call, press the“VOL+”button on the headset.
To decrease the volume during an active call, press the“VOL-“ button on the headset.
Muting the microphone
To mute the microphone during an active call
During an active call, press and hold the VOL+ button for approximately 3 seconds. A periodic
tone can be heard in the speaker when the microphone is muted.
To end the mute function
When the microphone is muted, quickly press the VOL+ button on the BLUETREK® X3.The
periodic tone will end.
Transferring a call from BLUETREK® X3 to the mobile phone
With a phone in Headset Profile
During an active call, to transfer it to the phone, simply turn off your headset.
With a phone in Hands-Free Profile
During an active call, to transfer it to the phone, press the TALK button for about 2 seconds.
English
BLUETREK X3 I 8
Transferring a call from the mobile phone to the BLUETREK® X3
With a phone in Headset Profile
Switch on your headset.
With a phone in Hands-Free Profile
During an active call on the mobile phone, press the TALK button for about 2 seconds to
transfer the call.
This function may not be available depending on your phone.
Call waiting
When you hear a call waiting alert while you are on a call, press approx. 3 seconds on the
TALK button to accept the second call and place the current call on hold.
To switch between an active call and a hold call, press approx. 3 seconds on the TALK button.
To end the active call and take the hold call, press once on the TALK button.
This function may not be available, depending on your phone. However, you can always
answer the second call from your phone keypad.
XS S*
M* L*
English
9 I BLUETREK X3
Wearing the BLUETREK® X3
Two different sizes of ear hooks are included in the
pack to suit your ear size.
Fitting the Ergobud*
4 different sizes of Ergobud* are included in the pack to
suit your ear size. You can adjust the Ergobud position
that you feel the most comfortable.
To replace the
Ergobud*, remove
the speaker cover by
pulling gently out
from the speaker.
Place the Ergobud*
back onto the speaker
by inserting the
bottom part first.
*Registered trademark pending
Other manuals for X3
2
Table of contents
Other BlueTrek Headset manuals
BlueTrek
BlueTrek S21 User manual
BlueTrek
BlueTrek BT01 User manual
BlueTrek
BlueTrek G2 User manual
BlueTrek
BlueTrek E2 User manual
BlueTrek
BlueTrek UFO User manual
BlueTrek
BlueTrek X3 User manual
BlueTrek
BlueTrek S21 User manual
BlueTrek
BlueTrek CRESCENDO - User manual
BlueTrek
BlueTrek Tattoo User manual
BlueTrek
BlueTrek G2 User manual
BlueTrek
BlueTrek Mini User manual
BlueTrek
BlueTrek CRESCENDO - User manual
BlueTrek
BlueTrek METAL EVOLUTION User manual
BlueTrek
BlueTrek X2 User manual
BlueTrek
BlueTrek Metal User manual
BlueTrek
BlueTrek Mini-Clip User manual
BlueTrek
BlueTrek Sugar User manual
BlueTrek
BlueTrek M2 User manual
BlueTrek
BlueTrek ORANGE Y2-2 User manual
BlueTrek
BlueTrek G2 User manual
