Black Box LBT01A-KIT User manual

BL A C K B O X®

Transmits up to 100-/60-Mbps downstream/

upstream data up to 984.2 feet (300 meters)

over a single twisted pair of copper wire.

Supports 30-/10-Mbps at distances up to 3280 feet (1 km).

10/100BASE-T Ethernet Extender over VDSL2

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax

724-746-0746 • Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence,

PA 15055-1018 • Web site: www.blackbox.com • E-mail: info@blackbox.com

Customer

Support

Information

LBT01A-KIT

Page 2 724-746-5500 | blackbox.com

FCC and IC RFI Statements/ NOM Statement

FEDERAL COMMUNICATIONS COMMISSION AND

INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio-frequency energy,

and if not installed and used properly, that is, in strict accordance with the

manufacturer’s instructions, may cause interference to radio communication.

It has been tested and found to comply with the limits for a Class A computing

device in accordance with the specifications in Subpart B of Part 15 of FCC rules,

which are designed to provide reasonable protection against such interference

when the equipment is operated in a commercial environment. Operation of

this equipment in a residential area is likely to cause interference, in which case

the user at his own expense will be required to take whatever measures may be

necessary to correct the interference.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise

emission from digital apparatus set out in the Radio Interference Regulation

of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les

limites applicables aux appareils numériques de la classe A prescrites dans le

Règlement sur le brouillage radioélectrique publié par Industrie Canada.

Normas Oficiales Mexicanas (NOM)

Electrical Safety Statement

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes

de que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para

referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de

operación deben ser respetadas.

Page 3

724-746-5500 | blackbox.com

NOM Statement

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,

cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,

etc.

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales

que sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea

recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá

lo descrito en las instrucciones de operación. Todo otro servicio deberá ser

referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no

interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,

alfombra o superficie similar puede bloquea la ventilación, no se debe

colocar en libreros o gabinetes que impidan el flujo de aire por los orificios

de ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor

como radiadores, registros de calor, estufas u otros aparatos (incluyendo

amplificadores) que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del

tipo descrito en el instructivo de operación, o como se indique en el

aparato.

12. Precaución debe ser tomada de tal manera que la tierra fisica y la

polarización del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no

sean pisados ni pellizcados por objetos colocados sobre o contra ellos,

poniendo particular atención a los contactos y receptáculos donde salen

del aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las

recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las

lineas de energia.

Page 4 724-746-5500 | blackbox.com

NOM Statement

16. El cable de corriente deberá ser desconectado del cuando el equipo no sea

usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean

derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en su

desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

Page 5

724-746-5500 | blackbox.com

Trademarks Used in this Manual

Black Box and the Double Diamond logo are registered trademarks of

BB Technologies, Inc.

Any other trademarks mentioned in this manual are acknowledged to be

the property of the trademark owners.

Page 6 724-746-5500 | blackbox.com

Table of Contents

Chapter Page

1. Specifications............................................................................................ 7

1.1 General ............................................................................................ 7

1.2 Data Rates and Distances................................................................. 7

2. Overview .................................................................................................. 8

2.1 Introduction ..................................................................................... 8

2.2 Features............................................................................................ 8

2.3 What’s Included ............................................................................... 9

2.4 Hardware Description....................................................................... 9

2.5 Typical Application ..........................................................................11

3. DIP Switch Settings..................................................................................12

4. LED Indicators..........................................................................................13

Page 7

724-746-5500 | blackbox.com

Chapter 1: Specifications

1. Specifications

1.1 General

Autodetection — Autodetects 10/100BASE-T and half-/full-duplex, automatic

MDI/MDI-X

Coding — Trellis code with 1024 DMT bins

Standards — VDSL Transmission: ITU-T G.993.1/2 SG15Q4 DT standard;

LAN Interface: IEEE 802.3/IEEE 802.3u

Connectors — VDSL: (1) RJ-11 for DSL or 3-pin terminal block;

POTS: (1) RJ-11;

LAN Interface: (1) RJ-45

Indicators — (4) LEDs: (1) Power, (1) DSL for VDSL Loop Connection Status,

(1) LAN, (1) Master/Slave (M/S)

Temperature Tolerance — 32 to 122° F (0 to 50° C)

Humidity Tolerance — 5 to 95%, noncondensing

Power — 5 VDC, 1 A

Size — 4.7"H x 3.5"W x 1.1"D (12 x 9 x 2.8 cm)

1.2 Data Rates and Distances

Table 1-1. Full-rate 26 AWG line performance at 6 dB.

Downstream Data Rate

(Mbps)

Upstream Data Rate

(Mbps) Distance (feet)

100 60 500

98 53 1000

90 44 1250

80 36 1500

70 27 1750

60 18 2000

48 11 2500

39 83000

35 3.5 3500

28 0.3 4000

Page 8 724-746-5500 | blackbox.com

Chapter 2: Overview

2. Overview

2.1 Introduction

The 10/100BASE-T Ethernet Extender over VDSL2 (very high-bit-rate digital

subscriber line) provides a broadband transmission up to 100-/60-Mbps

downstream/upstream data rates over a single twisted-pair copper line for

point-to-point Ethernet. At 100-/60-Mbps data rates, the extender supports

transmission distances up to 984.2 feet (300 meters), and provides a

30-/10-Mbps data rate for a 3280 feet (1 km) connection. Users may also select

a fixed data rate or a fixed SNR margin for different copper line ranging.

With plug-and-play features and minimum installation time, you can configure

each extender for either CO for central side or RT for remote side by setting DIP

switches. The extender conforms to ITU-T G.993.1 and G.993.2 to meet VDSL/

VDSL2 and SG15Q4 DMT standards for network requirements. Use a pair of

extenders for bandwidth-hungry applications such as LAN-to-LAN connectivity,

video streaming, FTTB, and MDU/MTU over a single twisted-pair telephone line.

2.2 Features

• Complies with ITU-T G.993.1, G.993.2 VDSL/VDSL2 and SG15Q4 DMT

standards.

• Enables 100-/60-Mbps downstream/upstream speeds for distances up to

984.2 feet (300 meters).

• Supports VDSL2 connections up to 6561.6 feet (2000 meters).

• Supports Annex A, B, or C for internal splitter (option).

• Protects against line surges.

• Has (1) RJ-11 connector or (1) three-pin terminal block for DSL link.

• Includes (1) RJ-11 connector for PHONE or POTS interface.

• Has (1) RJ-45 connector for Ethernet LAN port.

• Includes four LED Indicators.

• Provides (4) DIP switches for configuration settings.

• Supports Trellis coding up to 1024 Discrete Multi-Tone (DMT) bins.

• Uses Auto MDI-X for the 10/100BASE-T Ethernet LAN port.

• Has low-latency for video/voice/data applications.

Page 9

724-746-5500 | blackbox.com

Chapter 2: Overview

• You can select Fast and Interleaved modes: Fast mode guarantees a minimum

end-to-end latency less than 1 ms. Interleaved mode provides impulse noise

protection for any impulse noise with a duration less than 250 us. Interleaved

mode has a maximum end-to-end latency of 10 ms. Interleaved mode is the

default mode.

• You can also select fixed data rate and fixed SNR margin: Choose fixed SNR

margin (9 dB) or fixed target data rate. When fixed SNR margin is selected, the

systems will maintain the SNR margin at 9 dB across all available loop length.

When fixed target data rate is selected, the system will lock the data rate at

50-/20-Mbps whenever the calculated SNR margin is higher than 9 dB. This will

result in the best system stability and is the default mode.

2.3 What’s Included

Your package should contain the following items. If anything is missing or

damaged, contact Black Box Technical Support at 724-746-5500 or

info@blackbox.com.

• (2) 10/100BASE-T Ethernet Extenders over VDSL2

• (2) AC-to-DC Power Adapters (5-VDC/1-A) with (1) EU power clip

• (1) CD-ROM containing this user manual in PDF format

• (2) 3-position terminal blocks

• (8) rubber feet

• (8) screws

• (2) RJ-11 cables

2.4 Hardware Description

Figures 2-1 and 2-2 show the extender’s front and back panels. Table 2-1

describes its components.

1 2 3 4 5

Figure 2-1. Front panel.

Page 10 724-746-5500 | blackbox.com

Chapter 2: Overview

6 7 8 9 10

Figure 2-2. Back panel.

Table 2-1. 10/100BASE-T Ethernet Extender components.

Number Component Description

1Power LED Lights green when power is on

2LAN LED

Lights green when LAN is connected

Flashing green when LAN is active

3DSL LED Lights green when VDSL is connected

Flashing green when VDSL is in line handshakking

4M/S LED Selects master or slave (OFF = Master; ON = Slave)

54-position DIP switch Used for configuration settings: See Table 3-1

6Barrel connector Links to power

7RJ-11 connector Links to telephone line

8RJ-11 connector Links to VDSL interface

93-pin terminal block Connects to ring/tip/frame ground

10 RJ-45 connector Connects to LAN interface

Table of contents

Other Black Box Extender manuals

Black Box

Black Box AC1081A User manual

Black Box

Black Box CAT5 ClassWork Plus Multiloop User manual

Black Box

Black Box ServSwitch ACUR004A User manual

Black Box

Black Box Wizard ACU50 A Series User manual

Black Box

Black Box IC402A-R2 User manual

Black Box

Black Box ServSwitch ACU3201A User manual

Black Box

Black Box LB200A-R4 User manual

Black Box

Black Box IC247A User manual

Black Box

Black Box LWE120UK User manual

Black Box

Black Box LB304A User manual

Black Box

Black Box VX-VGA520-TA User manual

Black Box

Black Box LB532A-M User manual

Black Box

Black Box ACU1700A User manual

Black Box

Black Box LB300A-R3 Installation and operating instructions

Black Box

Black Box AVX-HDMI2-HDB User manual

Black Box

Black Box EMD4000R User manual

Black Box

Black Box LB304A User manual

Black Box

Black Box ServReach KVMCube User manual

Black Box

Black Box IC406A User manual

Black Box

Black Box ACS2009A-R2 User manual

Black Box

Black Box ACS110 User manual

Black Box

Black Box ServSwitch ACS253A-CT User manual

Black Box

Black Box KVX Series Instructions for use

Black Box

Black Box IC553A User manual

Popular Extender manuals by other brands

SY HDBT-60T installation guide

Appsys ProAudio

Appsys ProAudio ADX-16 user manual

Atlona

Atlona RS232 user manual

IDK

IDK OPF-TH1000-A user guide

Enable-IT

Enable-IT 824WP quick start guide

Worx

Worx Landroid RadioLink WA0864 Get started

TP-Link

TP-Link TL-WA730RE user guide

Camplex

Camplex CMX-HDMI-SFPL user manual

SC&T

SC&T HE03-4K user manual

Marmitek

Marmitek MegaView70 user manual

Samsung

Samsung SCS-26UC4 user guide

Foxun

Foxun SX-GES24 operating instructions

MuxLab

MuxLab 500771 Operation manual

foxunhd

foxunhd SX-AEX01 operating instructions

TERK Technologies

TERK Technologies LFIRX2 owner's manual

Devolo

Devolo Audio Extender supplementary guide

Edimax

Edimax EW-7438RPn V2 instructions

Shinybow USA

Shinybow USA SB-6335T5 instruction manual