Bkav AI VIEW P450 User manual
Qualcomm products contained herein are products of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.
The Made with Qualcomm Technologies logo is a trademark of Qualcomm Incorporated.
4k dome
AI-BASED CAMERA
Model: P450
Product number: 0803F/0802N/0803FW/0802NW
INSTALLATION GUIDE
PRODUCT KIT
Camera
Installation guide Drilling position decalThank you letter
3
Hex tool
Set 4 of screws
and anchors
Ø 5 mm, 5 holes
WALL DECAL FOR
DRILLING POSITION
GPS antenna
(Option)
Qualcomm products contained herein are products of QualcommTechnologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.
The Made with Qualcomm Technologies logo is a trademarkof Qualcomm Incorporated.
4k dome
AI-BASED CAMERA
Waterproof
couplings
TECHNICAL SPECIFICATION
Protection standards
Resolution, frame rate
IP66, IK10
UHD 3840 x 2160, 60fps
Mirco SD card External, up to 256GB
Optical zoom
P450-0803F / P450-0803FW: 3x
P450-0802N / P450-0802NW: 2x
Focal length
P450-0803F / P450-0803FW: 10.9 - 29mm ± 5%
P450-0802N / P450-0802NW: 4.36 - 9.33mm ± 5%
Field of view (horizontal - vertical)
P450-0803F / P450-0803FW: Near: 42° - 22.8° / Far: 15° - 8.4°
P450-0802N / P450-0802NW: Near: 111.96° - 58.11° / Far: 47.23° - 26.53°
Power supply
POE IEEE802.3af/802.3at
Maximum 13W, 12VDC
Weight
Environmental conditions
-40°C - 50°C (-40°F - 122°F)
Humidity 10 - 100%
Dimentions (L x W x H) L142 x W142 x H101.6mm
2kg
4
Camera body
12VDC power supply
RJ45 terminal block
Camera lens
Dust and waterproof lens protector
Infrared LED
PRODUCT OVERVIEW
5
INSTALLATION GUIDE
Step 1: Apply position decal and then drill 4 anchors to the wall. Put the camera onto the wall using 4 screws
to fix the camera ceiling mount (Figure 1).
Step 2: Fit the protective cover in the camera body to prevent dust and water, then fix it with 4 screws
(Figure 2).
1 2
6
Drilling position decal
7
CONNECTING THE SIGNAL WIRE
Two options to connect devices:
Option 1: Use the network cable connected from the PoE switch to the waiting RJ45 terminal block, no need
to use 12VDC power supply (Figure 1).
Option 2: Use 12VDC power supply and the network cable connected from the switch (Figure 2).
1
RJ45
PoE switch
2
RJ45
12VDC
Connect the PoE cable. Insert the cable into the
waterproof coupling before connecting the wires
into the terminal.
8
GPS ANTENNA INSTALLATION
Step 1: Use the screw unscrew tool in the position, as in the figure below.
Step 2: Use sharp-pointed pliers to insert the GPS antenna connector into the waiting cable terminal
(tighten enough screw thread).
Step 3: Fix the GPS antenna onto the camera body using silicone glue, as in the figure below.
GPS antenna
ADJUSTING THE CAMERA VIEWING ANGLE
80°
65°
9
10
THE MEMORY CARD AND RESET INSTALLATION
Mirco SD card
Reset factory
Power off the camera, press and hold the factory reset button. Continue to hold the factory reset button
for another 10 seconds while powering the camera, the camera will be restored to factory settings.
Note:
Reset installation: Open the protective cover that protects the camera against dust and water to reset the device.
Memory card: Open the protective cover, you can find the location of Micro SD card.
This manual suits for next models
4
Table of contents
Other Bkav Security Camera manuals
Bkav
Bkav AI View P200-0802GN User manual
Bkav
Bkav AI VIEW ULTRA ZOOM BULLET S200 User manual
Bkav
Bkav AI View P450-0802GN User manual
Bkav
Bkav AI View S200-0233 User manual
Bkav
Bkav AIView S201 User manual
Bkav
Bkav AI VIEW S500 User manual
Bkav
Bkav AI View P400 User manual
Bkav
Bkav AI View S500-0233 User manual
Bkav
Bkav AI VIEW C300-0200 User manual
Bkav
Bkav AI VIEW C300-0200 User manual
