BIXOLON DX420 User manual
Scker Printer 101
Scope:
Unit Descripon:
This document is used to help diagnose and troubleshoot a Bixolon DX420
Printer Parts Front Printer Parts Back Printer Parts Internal
Contact Us:
e: support@onsitetrackeasy.com.au
p: 1300 131 194
w: pegasus.net.au
How to Install a Scker Roll:
This document is used to help diagnose and troubleshoot a Bixolon DX420
1. Open the Paper Cover 2. Spread the Paper Holder
and insert the paper roll
2. Pull the paper so that it extends out of the front of the printer*.
Push the paper under both of the paper guides.
* Whether the paper label is wound inwards or outwards, its printing
surface must face up.
Contact Us:
e: support@onsitetrackeasy.com.au
p: 1300 131 194
w: pegasus.net.au
Basic Troubleshoong:
Error Lights: If the printer isn’t behaving as expected, use this table to determine what the issue may be. (Red = Most likely, Orange = Less likely)
NOTE: This information will come in handy when talking to an Onsite Support Technician during remote support process
Contact Us:
e: support@onsitetrackeasy.com.au
p: 1300 131 194
w: pegasus.net.au
If the printer is displaying the more common errors highlighted above, you are free to attemot to rectify it by wither replacing the sticker roll or cleaning the
machine (see Cleaning Instructions).
The self-test function checks whether the printer has any problems.
- Firmware version, printer conguration information, printing quality
checking pattern, and peripheral conguration information, etc.
Users cannot perform this procedure if using the printer’s label peel-off
option.
If the printer does not function properly, contact an authorised dealer.
The self-test checks the following:
1. Make sure that the paper roll has been installed properly
2. To begin the self-test turn on the power while pressing the feed button.
(Hold the button until the printer starts self-test printing).
If you are unable to resolve the issue or the problem persists, please call the Onsite Support Team on 1300 131 194 or email them on
support@onsitetrackeasy.com.au
Once you have spoken to an Onsite Support Technician complete the following steps:
Self Test:
Factory Reset:
This function is udes to reset the printer settings to factor defult settings.
How to reset the printer:
1. Press the Pause button for two seconds during Print Standby Mode.
2. Both LEDs will become an orange colour and the printer will be set to Stand-Alone Conguration Mode.
3. Press the Feed button at the third LED sequence (Status LED is green and LED 2 is blinking redfour times) to reset the printer to factory settings, and
Smart Media Detection funstion will be executed.
If neither the Self Test nor the Factory Reset resolve the issue, the Onsite Technician will advise you of the next steps.
Contact Us:
e: support@onsitetrackeasy.com.au
p: 1300 131 194
w: pegasus.net.au
General Informaon:
Cleaning the Unit:
Printing quality might be degraded by dust, foreign substance, adhesive substance, or other pollution materials stuck in the printer head or inside the printer.
When dirty, clean the print head as follows:
*CAUTION
- Make sure to turn the printer off prior to cleaning.
- As the print head gets very hot during printing, if intending to clean the print head, turn the printer power off and wait approximately 2-3 minutes before
commencement.
- When cleaning the print head, take care not to touch the heated portion of the print head.
- The printer head is susceptible to damage from static electricity, etc.
- Take care not to allow the print head to become scratched and/or damaged in any way.
Contact Us:
e: support@onsitetrackeasy.com.au
p: 1300 131 194
w: pegasus.net.au
Contact Us:
e: support@onsitetrackeasy.com.au
p: 1300 131 194
w: pegasus.net.au
Cleaning Instrucons:
1. Open the paper cover and then remove the paper.
2. Remove any dust or foreign substance using a dry cloth or cotton
swab.
3. Soak the cloth or cotton swab in alcohol for medical use and use it
to remove adhesive foreign substances or other pollution materials.
4. After cleaning the parts, do not use the printer until the alcohol has
evaporated completely (1-2 minutes) and the printer has completely
dried.
Note: Clean the parts when there is a degradation of performance the
in printing quality or paper detection.
Table of contents
Other BIXOLON Printer manuals
BIXOLON
BIXOLON SPP-C200 Installation instructions
BIXOLON
BIXOLON SPP-R310 User manual
BIXOLON
BIXOLON SRP-770II User manual
BIXOLON
BIXOLON SPP-R300 User manual
BIXOLON
BIXOLON STP-103II User manual
BIXOLON
BIXOLON STP-103 Installation instructions
BIXOLON
BIXOLON SPP-R200II User manual
BIXOLON
BIXOLON SRP-500 User manual
BIXOLON
BIXOLON SRP-275 User manual
BIXOLON
BIXOLON SRP-275II User manual
BIXOLON
BIXOLON SPP-R410 User manual
BIXOLON
BIXOLON SRP-350II Installation and operation manual
BIXOLON
BIXOLON SRP-S200 User manual
BIXOLON
BIXOLON SRP-350II User manual
BIXOLON
BIXOLON SPP-R200II Instruction manual
BIXOLON
BIXOLON SPP-R200 User manual
BIXOLON
BIXOLON SRP-S3000 Installation and operating manual
BIXOLON
BIXOLON SRP-350plusIIA User manual
BIXOLON
BIXOLON SRP-350IIOBE User manual
BIXOLON
BIXOLON SRP-350IIOBEi User manual
