Binks 80-228 User manual

External Mix Air Nozzle Application

OPERATION:

1. Connect hose as shown in diagram.

2. Fill cup with strained fluid mixed in accordance with

manufacturer’s recommendations on label of container.

3. Fasten cover securely.

4. Close air adjusting valve by turning clockwise.

5. Set air pressure at oil and water extractor (transformer)

to between 35 and 80 PSI, depending upon atomiza-

tion desired.

6. Set regulator on pressure cup to approximately 10 PSI

for enamels; 5 PSI for lacquers. (Turn knob clockwise

to increase pressure; to reduce pressure, turn knob

counter-clockwise. Always release air in cup by

momentarily opening air release valve on cover when

attempting to reduce pressure.)

7. Open air adjusting valve.

8. With trigger fully pulled back, make several fast spray

strokes against a flat surface. After adjustment of pres-

sure, proper atomization will be indicated by an even

distribution of finely divided paint particles.

Binks Model 80-228 (2 QT.)

“STEADI-GRIP” PRESSURE

CONTAINER

Replaces

Part Sheet

1619R-9

Part

Sheet

77-1619R-10

Air from Oil and

Water Extractor

(Transformer)

Fluid Pressure

Gauge

Safety Valve

(Do not tamper

with or readjust)

Fluid Pressure

Regulator

Knob

Lubricate Cup

Threads

Air

Adjusting

Valve

Fluid

Hose

Air Hose

Air Release

Valve

Air Nozzle

IMPORTANT

The most efficient atomization air pressure is the lowest

air pressure that will properly atomize the paint. This will

minimize the overspray, deposit more paint on the surface

and eliminate paint wastage.

If a faster coverage is necessary, first increase fluid pres-

sure and then adjust atomization air pressure. If a slower

coverage is more desirable, first reduce the fluid pressure

and then adjust atomization air pressure. Always attempt

to maintain the lowest pressures for maximum efficiency.

For ease of removing cup cover and to prevent leakage,

always thoroughly grease the threads on cup.

CLEANING

1. Open air release valve on pressure cup cover.

2. Reduce pressure in cup until gauge reads zero, (turn

knob counter-clockwise).

3. Loosen cup cover and set fluid tube on angle in cup.

4. Loosen air nozzle two turns, place cloth over nozzle

and pull the trigger to force paint into cup.

5. Remove cover and clean cup and cover thoroughly.

6. With approximately 1/4 to 1/2 cup of clean solvent, attach

cover and set fluid pressure at approximately 10 PSI.

7. Close air adjusting valve at spray gun.

8. Trigger gun and allow solvent to flow into a container

until it flows clear.

9. Remove solvent, then clean air nozzle. If any dirt

appears in orifice, clean with tooth pick; wire will

damage nozzle. Blow nozzle and cup dry. Replace

nozzle and cover loosely.

Internal Mix Air Nozzle Application

OPERATION

The internal mix air nozzle accomplishes atomization by

mixing the air and fluid within the air nozzle.

1. Close air adjusting valve by turning clockwise.

2. Set air pressure at oil and water extractor (transformer)

to approximately 45 PSI.

3. Open air adjusting valve and allow air to enter the gun.

4. Set fluid pressure at 20 lbs. and adjust higher or lower

until desired atomization is effected. Air pressure

should be alternately adjusted.

CAUTION

If the cup is accidentally tipped over or held at too great an

angle, fluid will load up the underside of cup cover, and leak

into regulator. In the event this happens, clean immediately!

NOTE

The steps are the same as with the external mix nozzles,

except the air and fluid pressure settings are different.

NOTE

Never allow solvent to remain in cup; solvent vapors tend

to reduce service life of gasket. Separate storage of cup

and cover recommended.

ITEM PART

NO. NO. DESCRIPTION QTY.

120-353■HEX JAM NUT 5/16"

220-1830-5•■

❍

SCREW (No.6-32 x 1/4 Rd. Hd. Machine)

357-125-5•■

❍

CHECK VALVE WASHER

472-1022

★

CENTER POST ASSEMBLY ................ 1

580-4 CUP (2 Quart) ...................................... 1

680-11-5

❍

COVER GASKET (Tri Seal Foam)............ 1

780-12 RELIEF VALVE STEM ........................ 1

880-25•■CHECK VALVE

980-26-5•■

❍

CHECK VALVE SPRING

ITEM PART

NO. NO. DESCRIPTION QTY.

10 80-33 FLUID OUTLET .............................. 1

11 80-34 FLUID TUBE (2 Quart) ...................... 1

12 80-42*

■

COVER

13 80-43* COVER ASSEMBLY ........................ 1

14 80-45* COVER GASKET (Leather)................ 1

15 80-225 CONTAINER COVER ...................... 1

16 80-226• CHECK VALVE BRACKET .............. 1

17 83-1899 HANDLE ........................................ 1

18 85-237▲REGULATOR ASSEMBLY .............. 1

PARTS LIST

When ordering, please specify Part No.

Binks Model 80-228 (2 QT.) “STEADI-GRIP” PRESSURE CONTAINER

*Accessories available.

•Included in Spare Parts Kit No. 80-27.

▲ Item 18 ref. Part Sheet 2417.

■ Items NOT available separately.

★Available from Industrial Finishing distributors only.

❍Available only as 5-pack.

■

Available in Spare

Parts Kit 80-27

only. Items NOT

available

separately.

★

ITW Industrial Finishing

Binks has authorized distributors throughout the world. For technical

assistance or the distributor nearest you, see listing below.

U.S./Canada Technical Service Office:

195 Internationale Blvd., Glendale Heights, IL 60139

Toll-Free Telephone: 1-888-992-4657 (U.S.A. and Canada only)

Toll-Free Fax: 1-888-246-5732

ITW Automotive Refinishing

Binks has authorized distributors throughout the world.

For equipment, parts and service, check the Yellow Pages

under “Automotive Body Shop Equipment and Supplies.”

For technical assistance, see listing below.

U.S./Canada Customer Service Office:

1724 Indian Wood Circle, Suite J-K, Maumee, OH 43537

Toll-Free Telephone: 1-800-445-3988 (U.S.A. and Canada only)

Toll-Free Fax: 1-800-445-6643

Binks Worldwide Sales and Service Listing: www.binks.com

WARRANTY

This product is covered by Binks’ 1 Year Limited Warranty.

77-1619R-10 Revisions: Updated contact information.

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

DeVilbiss

DeVilbiss LUNA2i Operation manual

Graco

Graco HydroShield WMBH00 Instructions - parts