Binks 80-295-CE User manual

Binks “STEADI-GRIP”

2 QT. PRESSURE CUPS

Model No. 80-295-CE

SB-E-4-231

ISS.01

SPECIFICATIONS

MAX. WORKING PRESSURE . . . . . . . . . . . . . . . . . . . . 50 psig 3.5 bar

OVERALL HEIGHT

WITH AUXILIARY HANDLE . . . . . . . . . . . . . . . . . 16 15/16 in 430 mm

WITHOUT AUXILIARY HANDLE . . . . . . . . . . . . . 13in 330 mm

BASE DIAMETER . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . 5 1/4in. 133 mm

AIR INLET & OUTLET CONNECTION SIZE . .. . . . . . . . 1/4 NPS (m) -

FLUID OUTLET CONNECTION SIZE . . . . . . .. . . . . . . . 3/8 NPS (m) -

FLUID CAPACITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Qts (US) 1.9 Ltr

WEIGHT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 lb.3oz. 1.46 kg

The following hazards may occur during the normal use of this equipment. Please read the following

chart.

HAZARD CAUSE SAFEGUARDS

FIRE

Solvents and coatings can be

highly combustible, especially

when sprayed.

1. Adequate exhaust must be provided

to keep the air free of

accumulations of flammable

vapours

2. Smoking must never be allowed in

the spray area.

3. Fire extinguishing equipment must

be present in the spray area.

FIRE - PRESSURE CUP Vapours from flammable liquids

can catch fire or explode

1. Keep Cup at least 3 metres away

from sources of ignition, including

hot surfaces, mechanical sparks

and arcing (non-explosion proof)

electrical equipment.

2. Electrostatic charges may

accumulate and may ignite

flammable vapours by brush

discharges. Ensure the Cup is

earthed with conductive air or fluid

hoses or earthing clamp.

INHALING TOXIC

SUBSTANCES

Certain materials may be

harmful if inhaled, or there is

contact with the skin.

1. Follow the requirements of the

Material Safety Data Sheet supplier

by the coating manufacturer.

2. Adequate exhaust must be provided

to keep the air free of

accumulations of toxic materials.

3. Use a mask or respirator wherever

there is a risk of inhaling sprayed

materials. The mask must be

suitable for the material being

sprayed.

EXPLOSION, PRESSURE

TANK—RUPTURE

Making any changes or

modification to the pressure Cup

may weaken it.

1. Never drill into, weld or modify the

Cup in any way.

2. Do not adjust, remove or tamper

with the safety valve.

3. Only replace the safety valve with

the correct spare part as listed.

4. Do not fit any other safety valve of a

higher pressure rating than the

maximum working pressure of the

Cup.

GENERAL SAFETY Improper operation or

maintenance may create a

hazard.

Operators should be given adequate

training in the safe use and

maintenance of this equipment. Refer

to Pressure Systems Safety

Regulations 2000 Approved Code of

Practice or other national codes.

WARNING

SETUP AND OPERATION

Refer to “TYPICAL INSTALLATION” drawing below

Set up the “Steadi-Grip” with the CONVENTIONAL or HVLP gun along with at least 1.5m (5 ft.) of air

and fluid hose. Attach air hose from extractor to air inlet on handle of steadigrip assembly. Pour paint

into canister with liner. Re-attach lid to canister and firmly tighten four knobs over canister lid. Set air

pressure from air regulator mounted on extractor and fluid pressure by adjusting fluid pressure

adjustment knob on cup handle.

INTRODUCTION

Binks “Steadi-Grip” Pressure Cups are CE marked in accordance with the

ATEX Directive 94/9/EC, Cat 2 G X for use in Zones 1 and 2.

These Cups are ideal for component spraying and industrial applications where small batch

production spraying is required. The 2 qt. capacity is sufficient to complete large spray jobs without

refilling the cup. Its lightweight and rugged construction is excellent for portability allowing the

operator to make fluid and air control adjustments quickly and efficiently at the spray station.

NOTE

Before refilling canister with paint, shut

odd air supply to the cup and release

pressure from canister by rotating pres-

sure relief knob counter clockwise

WARNING

Chlorinated solvents and aluminum are incompatible and

will cause an adverse chemical reaction, possibly resulting

in bodily injury. Under NO circumstances should

chlorinated solvents be used with the “Steady Grip

Pressure Cup”.

CAUTION

Do not exceed 100 PSIG input air pressure

into the cup. Excessive pressure could dam-

age components

WARNING

All air and fluid pressure in the system must be relieved

before servicing the cup and before cup is filled or cleaned.

Attempting to service the cup while pressurized could result

in damage to components or personal injury.

PARTS LIST

ITEM

PART

DESCRIPTION QTY

1 20-353-1 HEX JAM NUT 5/16" 1

4 †72-1022 CENTER POST ASSEMBLY 1

5 80-4 CUP (2 Quart) 1

6 ○80-11-5 COVER GASKET (Tri Seal

Foam) 1

7 80-12 RELIEF VALVE STEM 1

8 80-267 CHECK VALVE 1

9 ○60-7 CHECK VALVE SPRING 1

10 80-33 FLUID OUTLET 1

11 80-34 FLUID TUBE (2 Quart) 1

14 *80-45 COVER GASKET

(Leather)................ 1

15 80-297 CONTAINER COVER

17 83-1899 HANDLE

18 ▲85-440 REGULATOR ASSEMBLY 1

* Accessories available

▲Item 18 ref. Part Sheet 2417

† Available from Industrial Finishing distributors only

○Available only as 5-pack

MODEL 80-295 PRESSURE CUP

Refer to “TYPICAL INSTALLATION” drawing

below

Set up the “Steadi-Grip” with the CONVENTIONAL or

HVLP gun along with at least 5 ft. of air and fluid

hose. Attach air hose from extractor to air inlet on

handle of steadigrip assembly. Pour paint into

canister with liner.

Re-attach lid to canister and firmly tighten four knobs

over canister lid. Set air pressure from air regulator

mounted on extractor and fluid pressure by adjusting

fluid pressure adjustment knob on cup handle.

CLEANING

1. Open air release valve on pressure cup cover.

2. Reduce pressure in cup until gauge reads zero,

(turn knob counter-clockwise).

3. Loosen cup cover and set fluid tube on angle in

cup.

4. Loosen air nozzle two turns, place cloth over

nozzle and pull the trigger to force paint into cup.

5. Remove cover and clean cup and cover

thoroughly.

6. With approximately 1/4 to 1/2 cup of clean solvent,

attach cover and set fluid pressure at

approximately 10 PSI.

7. Close air adjusting valve at spray gun.

8. Trigger gun and allow solvent to flow into a

container until it flows clear.

9. Remove solvent, then clean air nozzle. If any dirt

appears in orifice, clean with tooth pick; wire will

damage nozzle. Blow nozzle and cup dry.

NOTE

Before refilling canister with paint, shut

off air supply to the cup and release

pressure from canister by rotating

pressure relief knob counter clockwise

WARNING

Chlorinated solvents and aluminum are

incompatible and will cause an adverse

chemical reaction, possibly resulting in bodily

injury. Under NO circumstances should

chlorinated solvents be used with the “Steady

Grip Pressure Cup”.

WARNING

All air and fluid pressure in the system must

be relieved before servicing the cup and before

cup is filled or cleaned. Attempting to service

the cup while pressurized could result in

damage to components or personal injury.

SETUP AND OPERATION

EC DECLARATION OF CONFORMITY

We: ITW Finishing UK

Ringwood Rd

Bournemouth

Dorset

BH11 9LH

As the manufacturers representative of the items listed below:

TYPE : SG Pressure Feed Cup

MODEL: 80-295-CE

Declare, under our sole responsibility, that the equipment to which this

document relates is in conformity with the following standards or

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

DeVilbiss

DeVilbiss LUNA2i Operation manual

Graco

Graco HydroShield WMBH00 Instructions - parts