Baldor BC142 User manual

Baldor Electric Company, P. O. Box 2400, Ft. Smith, AR 72902-2400, (479) 646-4711, Fax (479) 648-5792

&DWDORJ1RV%&DQG%&6XSSOHPHQWDO,QIRUPDWLRQ

Part No. MN704-SUP

(A42130) - Rev. A03 - 5/21/2004 - Z2993A03 Page 1 of 1

IMPORTANT: The following information and instructions are to be used as a supplement to the Installation and Operation

Manual (Part No. MN704). The manual must be read and understood before attempting to operate this control.

• The General Performance Specifications, Electrical Ratings, and Mechanical Specifications of these controls have not changed •

• Jumper J2 (DC Output Voltage / Tach Selection) and Enable Connector (EN) have been added •

• Diagnostic LEDs for Power On and Current Limit • Now with SMT Construction •

 !"$#%&'%()*,+.-/01

To use the Enable Circuit, remove the jumper that is factory installed on CONN1.

Note: 1. For 50V/1000 tach-generator, connect to Terminals B (+) and I2 (-).

Application Note: When the control is stopped using Inhibit, the motor will coast to stop. When the control is

stopped using Enable, the motor will decelerate to stop. The deceleration time can only be made longer than the

normal coasting time of the load.

3,4 3*,+567

Jumper J2 (DC Output Voltage / Tach Selection)

Catalog No.

90 Volts DC

180 Volts DC

BC141

(Factory Setting) (Tach-Generator)

BC142

(Step-Down) (Factory Setting) (Tach-Generator)

Notes: 1. The 180V position, on Jumper J2, is not available on Catalog No. BC141. 2. The control

will run at full speed, if Jumper J2 is in the "T" position and the tach-generator is miswired.

DC DRIVE

BC141, BC142 & BC142-6 DC CONTROL

5/2004 MN704

Installation and Operation Manual

TABLE OF CONTENTS

Section Page

1 Simplified Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Safety Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4 Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5 Mounting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

6 Wiring Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

7 Setting Selectable Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

8 AC Line Fusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

9 Plug-In Horsepower Resistor® and Armature Fuse Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

10 Recommended High Voltage Dielectric Withstand Testing (Hi-Pot Testing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

11 Trimpot Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

12 Diagnostic LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

13 Switching Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

14 Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Tables

1 Electrical Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2 General Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 Minimum Supply Wire Size Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4 Field Connection (Shunt Wound Motors Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5 Plug-In Horsepower Resistor® and Armature Fuse Kit Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figures

1 Control Layout and General Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2 Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3 Remote Main Speed Potentiometer Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

TABLE OF CONTENTS (Continued)

Figures Page

4 Voltage Following Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5 Enable Switch or Contact Wired to the Enable Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

6 Enable Switch or Contact Wired to the Main Speed Potentiometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

7 Inhibit Switch or Contact Wired to the Inhibit Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

8 DC Tach-Generator Connection (7 Volts per 1000 RPM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

9 DC Tach-Generator Connection (50 Volts per 1000 RPM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

10 Other DC Tach-Generator Connection (with Addition of RT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

11 AC Line Input Voltage Selection (Jumper J1 (Catalog No. BC142-6 Only)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

12 Motor Voltage and DC Tach-Generator Selection (Jumper J2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

13 Hi-Pot Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

14 Acceleration Trimpot (ACCEL) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

15 Deceleration Trimpot (DECEL) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

16 Minimum Speed Trimpot (MIIN) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

17 Maximum Speed Trimpot (MAX) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

18 Current Limit Trimpot (CL) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

19 IR Compensation Trimpot (IR) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

20 Typical Dynamic Brake Circuit Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Items Included in this package – Speed Control, factory installed 25 Amp AC Line Fuse, Installation and Operation

Manual, Hardware Bag (contains Main Speed Potentiometer with insulator and mounting hardware, (9) – 0.25” female

crimp-on terminals, (4) – 0.11” female crimp-on terminals, and an Enable harness), CE Approved Product Information

Card, and Warranty Registration Card.

Items required to operate this control – Plug-In Horsepower Resistor® and Armature Fuse Kit. Supplied through

your distributor. See Section 9, on page 21.

Note: A Plug-In Horsepower Resistor® and Armature Fuse

Kit must be installed in order for this product to operate.

See Section 9, on page 21.

1 SIMPLIFIED INSTALLATION INSTRUCTIONS

1.1 AC Line Connection – Wire the AC line to Terminals “L1” (Line Fuse) and “L2”, as shown in Figure 1, on

page 10 and as described in Section 6.1, on page 13.

Catalog No. BC141 is rated for 115 Volt AC line input only. Catalog No. BC142 is rated for 230 Volt AC line

input only. Catalog No. BC142-6 is rated for 115 Volt AC line input (Jumper J1 in the “115V” position) and

230 Volt AC line input (Jumper J1 in the “230V” position). See Section 7.1, on page 19.

Notes: 1. The rated AC line voltage (115, 208/230) of the control must match the actual AC line input

voltage. 2. If one of the AC line inputs is a neutral (N), wire it to Terminal “L2”.

1.2 Ground Connection – Connect the ground wire (earth) to the control chassis.

1.3 Motor Connection – Connect the motor to Terminals “A+” (Armature Fuse) and “A-”, as shown in Figure 1,

on page 10, and as described in Section 6.3, on page 14.

1.4 Jumper Settings – Jumper J1 (on Catalog No. BC142-6 only) and Jumper J2 (all models) have been facto-

ry set for most applications, as shown in Figure 1, on page 10, and as described in Section 7, on page 19.

IMPORTANT – Read these simplified installation instructions before proceeding. These instructions are to be

used as a reference only and are not intended to replace the detailed instructions provided herein. You must

read the Safety Warning, on page 6, before proceeding.

Fuse Plug-In Horsepower

Resitor®

1.5 AC line Fusing – A 25 Amp AC line fuse is factory installed in the AC Line Fuse Holder, as shown in Figure

1, on page 10. It is recommended that this fuse be changed to a 12 Amp fuse for motors rated 7.5 Amps

DC or less. Fuse each conductor that is not at ground potential.

1.6 Plug-In Horsepower Resistor® and Armature Fuse – It is required that a Plug-In Horsepower Resistor®

and Armature Fuse be installed. These are supplied separately in a kit which is based on motor horsepower

and voltage. Select the correct kit as described in Section 9, on page 21.

1.7 Trimpot Settings – All trimpots have been factory set for most applications, as shown in Figure 1, on page

10. The trimpots may be readjusted, as described in Section 11, on page 24.

1.8 Diagnostic LEDs – After power has been applied to the control, observe the LEDs to verify proper control

operation, as described in Section 12, on page 28.

1.9 Auxiliary Heat Sink (Catalog No. BC143) – Extends the horsepower rating of the control to 1.5 HP for

controls with 90 Volt DC output and 3 HP for controls with 180 Volt DC output.

This product should be installed and serviced by a qualified technician, electrician, or electrical main-

tenance person familiar with its operation and the hazards involved. Proper installation, which includes

wiring, mounting in proper enclosure, fusing or other over current protection, and grounding can reduce the

chance of electrical shocks, fires, or explosion in this product or products used with this product, such as elec-

tric motors, switches, coils, solenoids, and/or relays. Eye protection must be worn and insulated adjustment tools

must be used when working with control under power. This product is constructed of materials (plastics, metals,

carbon, silicon, etc.) which may be a potential hazard. Proper shielding, grounding, and filtering of this product

can reduce the emission of radio frequency interference (RFI) which may adversely affect sensitive electronic

equipment. It is the responsibility of the equipment manufacturer and individual installer to supply this Safety

Warning to the ultimate end user of this product. (SW effective 11/1992). Be sure to follow all instructions care-

fully. Fire and/or electrocution can result due to improper use of this product.

Definition of Safety Warning Symbols:

Electrical Hazard Warning Symbol – Failure to observe this warning could result in electrical shock

or electrocution.

Operational Hazard Warning Symbol – Failure to observe this warning could result in serious injury

or death.

2 SAFETY WARNING – Please read carefully.

This product complies with all CE directives pertinent at the time of manufacture. Installation of a CE

approved RFI filter is required (see Section 14.8, on page 30). Additional shielded cable and/or AC

line cables may be required along with a signal isolator (Catalog No. BC152).

3 INTRODUCTION

Thank you for purchasing the BC141, BC142, or BC142-6 full-wave variable speed DC motor control, now with

SMT construction. The control offers the user the ultimate in reliability and performance at an affordable price. The

controls contain a unique patented super-fast Direct-Fed™ current limit circuit that protects the SCR power

bridge against direct shorts1. The reliability of the control is further enhanced with the use of high-surge, 25 Amp

SCRs, and AC line and armature fusing2, 3. The control is designed with exclusive Plug-In Horsepower

Resistor® 3, which eliminates the need for recalibrating IR Comp and Current Limit when the control is used on

various horsepower motors. In addition, the rating of the control can be extended to 1.5 HP for controls with 90

Volt DC output and 3 HP for controls with 180 Volt DC output, by the use of an Auxiliary Heat Sink4. Catalog Nos.

BC142 and BC142-6 also allow operation of 90 Volt DC motors when used on 208/230 Volt AC line input 5.

The versatility of the control is confirmed by its extensive list of standard features, such as: selectable armature

and tach feedback and adjustment trimpots for minimum speed, maximum speed, IR compensation, and linear

acceleration and deceleration. The control includes Auto-Inhibit®, which eliminates surging during rapid AC line

switching; pulse transformer triggering, which provides cogless operation at low speed; and superior noise rejec-

tion circuitry, which eliminates false starts and blown SCRs. Enable (normally closed) and Inhibit (normally open)

functions provide electronic switching of control output.

The output voltage of the control is a linear function of the Main Speed Potentiometer rotation. In addition, the

control can be used in a voltage following mode by supplying an isolated analog input signal to Terminals “P2” (+)

and “P1” (-). The control is compact in size (only 4.30” X 3.64” X 1.25”) and easily replaces all competitive speed

controls. The control is supplied with a factory installed 25 Amp AC line fuse and a 5 k ΩMain Speed

Potentiometer and QD terminals. All models are UL Listed (USA and Canada) and CE Approved.

Notes: 1. Short circuit protected at motor only. 2. Baldor Limited Warranty applies. See page 32. 3. Plug-In

Horsepower Resistor® and Armature Fuse Kit supplied separately. See Sections 8 and 9, on pages

20 - 22. 4. Catalog No. BC143. See Section 14.1, on page 30. 5. Step-Down operation.

3.1 Standard Features

1 Plug-In Horsepower Resistor® – Eliminates the need to calibrate the control for IR Compensation

and Current Limit when used on various horsepower motors.

2 Auto-Inhibit® – Allows the control to be rapidly switched “on” and “off” using the AC line.

3 Inhibit and Enable – Allows the control to be turned “on” and “off” using electronic switching.

4 Trimpots – Minimum Speed (MIN), Maximum Speed (MAX), IR Compensation (IR), Current Limit (CL),

Acceleration (ACCEL), and Deceleration (DECEL).

5 Jumpers – AC Line Input Voltage Selection (J1 (Catalog No. BC142-6 only)), Motor Voltage and DC

Tach-Generator Selection (J2).

6 Protection Features – MOV transient protection. Short Circuit protected (at motor only).

7 Diagnostic LEDs – Power On (PWR ON) and Current Limit (CL).

8Catalog No. BC141 operates on 115 Volt AC line input with 90 Volt DC motors.

9Catalog No. BC142 operates on 230 Volt AC line input with 180 Volt DC motors or 90 Volt DC motors

(step-down). - Jumper Selectable.

10 Catalog No. BC142-6 can operate on 115 Volt AC line input with 90 Volt DC motors and 230 Volt AC

line input with 180 Volt DC motors or 90 Volt DC motors (step-down). - Jumper selectable.

11 Armature or DC Tach-Generator feedback.

12 SMT construction.

Notes: 1. Step-down operation: motor may have reduced brush life. 2. Performance is for SCR rated permanent magnet motors only. Lower performance can be

expected with other motor types. Factory setting is for 3% load regulation. To obtain superior regulation, see Section 11.6, on page 27.

Catalog

Number

AC Line

Voltage

(±15%, 50/60Hz)

(Volts AC)

Motor

Voltage

(Volts DC)

Rating without Auxiliary Heat Sink Rating with Auxiliary Heat Sink

Field Voltage

(Volts DC)

Maximum AC

Line Current

(RMS Amps)

Maximum DC

Load Current

(Avg. Amps)

Maximum

Horsepower

(HP (kw))

Maximum AC

Line Current

(RMS Amps)

Maximum DC

Load Current

(Avg. Amps)

Maximum

Horsepower

(HP (kw))

BC141 115 0 - 90 12.0 8.0 .75 (.6) 24.0 16.0 1.5 (1.1) 50, 100

BC142 230 0 - 180 12.0 8.0 1.5 (1.1) 24.0 16.0 3 (2.3) 100, 200

0 - 90* 12.0 8.0 .75 (.6) 24.0 16.0 1.5 (1.1) 100

BC142-6

115 0 - 90 12.0 8.0 .75 (.6) 24.0 16.0 1.5 (1.1) 50, 100

230 0 - 180 12.0 8.0 1.5 (1.1) 24.0 16.0 3 (2.3) 100, 200

0 - 90* 12.0 8.0 .75 (.6) 24.0 16.0 1.5 (1.1) 100

TABLE 1 – ELECTRICAL RATINGS

TABLE 2 – GENERAL PERFORMANCE SPECIFICATIONS

* Step-down operation.

Description Specification Factory Setting

Speed Range (Ratio) 50:1 —

Armature Feedback Load Regulation (0 - Full Load, 50:1 Speed Range) (% Base Speed) 1 —

Tach-Generator Feedback Load Regulation (0 - Full Load, 50:1 Speed Range) (% Set Speed) 1 —

Line Voltage Regulation (at Full Load, ± 10% Line Variation) (% Speed) 0.5 —

Control Linearity (% Speed vs. Dial Rotation) 2 —

Acceleration (ACCEL) Trimpot Range (Seconds) 0.2 – 10 2

Deceleration (DECEL) Trimpot Range (Seconds) 0.2 – 10 2

Maximum Speed (MAX) Trimpot Range (% Base Speed) 50 – 110 100

Minimum Speed (MIN) Trimpot Range (% Base Speed) 0 – 30 0

Current Limit (CL) Trimpot Range (% Full Load) 0 – 200 150

IR Compensation (IR) Trimpot Range (at Specified Full Load @ 90, 180 Volts DC Output) (Volts DC) 0 – 24, 48 3, 6

This manual suits for next models

Table of contents

Other Baldor Controllers manuals

Baldor

Baldor VS1MD User manual

Baldor

Baldor VS1GV21-1B Installation instructions

Baldor

Baldor NextMove ST User manual

Baldor

Baldor Nextmove ESB User manual

Baldor

Baldor VS1SP User manual

Baldor

Baldor MDH1A05TB-RC23 User manual

Baldor

Baldor VS1GV Quick start guide

Baldor

Baldor VS1MX Installation instructions

Baldor

Baldor MicroFlex User manual

Baldor

Baldor ID15J1F50-ER User manual

Baldor

Baldor 22H series Installation instructions

Baldor

Baldor NXE100-1608Dx User manual

Baldor

Baldor NextMove ESB-2 User manual

Baldor

Baldor 15H SERIES 15H Installation instructions

Baldor

Baldor NextMove ES User manual

Baldor

Baldor VS1SM Installation instructions

Baldor

Baldor BC140 Installation instructions

Baldor

Baldor DBSC105-AAA-1 User manual

Baldor

Baldor DBSC 100 Series User manual

Baldor

Baldor VS1MXS51 Installation instructions

Baldor

Baldor MintDrive User manual

Baldor

Baldor LD Series User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual