Bachmann Williams E7A User manual
– Page 1 of 2 –
Bachmann Industries, Inc.
1400 East Erie Avenue, Philadelphia, PA 19124 USA
www.bachmanntrains.com
Customer Service Telephone 800-356-3910
E7A DUMMY DIESEL LOCOMOTIVE INSTRUCTIONS
Thank you for purchasing a Williams by Bachmann® locomotive. This locomotive has been manufactured to provide
years of use and enjoyment. Please follow the simple instructions below.
Before operating, please lightly lubricate the points shown in the diagram below. Do not over-lubricate and take extra care
to avoid getting lubricants on the wheel surfaces.
1. For the axles and coupler pivot points Marked A, we recommend that you lubricate with a small amount of light
oil such as Bachmann E-Z Lube® #99984 Light Gear Oil. Do not over-lubricate.
2. For areas that require electrical flow, such as roller pick-ups Marked B, please use Bachmann E-Z Lube®
#99981 Conductive Contact Lube. Never use any Teflon® based oil on these areas because this type oil has
insulating properties.
– Page 2 of 2 – Printed In China
OPERATION
After unpacking the locomotive, make sure that the uncoupling plunger is in the correct position with the pin inserted in
the knuckle (see figure 1). Failure to do so will allow the uncoupling plunger to contact the center rail and a direct short
will occur when power is applied to the track.
Uncoupling
This dummy locomotive is equipped with an operating knuckle coupler at the pilot end. The rear end of the locomotive
has a fixed coupler, to allow close coupling with the matching powered unit. To uncouple, position the uncoupling
plunger over the center of electro-magnetic track uncoupling section and activate the magnet.
PERIODIC MAINTENANCE
Disassembly Instructions
You will have to remove the body shell for bulb replacement, or to install a power upgrade kit. The body shell is attached
with four screws on the bottom of the locomotive frame. The screws are located in each corner of the frame. After
removing the four screws, you will need to GENTLY spread the body skirt that covers the fuel tank to release the body
from the molded fuel port on the side of the fuel tank. When you re-attach body shell, please be careful not to over-tighten
the screws.
Lubrication
We recommend that you lubricate as directed on page 1 every 10 hours of operation.
Light Bulb Replacement
This locomotive uses a 12 volt bayonet style bulb. The standard replacement bulb number is 53.
Power Upgrade Kit
A power upgrade kit, Williams by Bachmann® #00243, is available to convert this dummy unit into a powered unit.
Please follow the installation instructions that are included with the kit.
Bachmann Industries, Inc.
1400 East Erie Ave, Philadel
p
hia, PA 19124 USA
E-7 A (Dummy) Parts List Rev 10.22.08 Printed in China
1400
East
Erie
Ave,
Philadelphia,
PA
19124
USA
www.bachmanntrains.com
Customer Service Tele
p
hone 800-356-3910
P
art
N
um
b
e
r
D
escr
i
pt
i
on
N
um
b
er
U
se
d
E7 DUMMY A UNIT BODY & BODY PARTS
1027-E003 Body Shell - complete 1
1-30100DFT Screw(Mounts Body to Frame) 4
293-04-01 Ornamental Hor
n
2
1027 03 01 / 1027 03 02
Upper / Lower Headlight lens
1 each
1027
-
03
-
01
/
1027
-
03
-
02
U
pper
/
L
ower
H
ea
dli
g
h
t
l
ens
1
eac
h
309-01-01 Red Marker Lens 2
1027-X004R1 Windshield 1
1027-X003 Cab Window Glass 2
1027-X002 Side & Rear Window Glass 7
1027-M001R5E Metal Chassis 1
315-05-01 Fuel Tank 1
1-25060DPS Screw(Mounts Fuel Tank to Frame) 4
()
TRUCK PARTS
293-10-02B Truck Mount 2
293-M023FR1 Flanged Wheel 8
293-M12B Unflanged Wheel 4
293-M029NR5 Axle 6
1-30060DPM Truck Mounting Screw 2
293-E001 Operating Coupler Assembly 1
343-06-01 Non-Operating Couple
r
1
pgp
885-M013R1 Spring for non-operating couple
r
1
1-26060DPWM
M
ounting Screw for non-operating couple
r
1
1027-02-01 Pilot 1
1-30180DFM Pilot / Rear Ladder Mounting Screw 2
322-E003 Roller Pickup Assembly 1
322-08-01 Top Insulator for Roller Pickup 2
322-08-02 Bottom Insulator for Roller Pickup 2
1-26180DPM Roller Pickup Mounting Screw 2
pg
330-05-01 Sideframe - Left 2
330-05-02 Sideframe - Righ
t
2
293-M021B Front Truck Ladder 1
1027-M003R3B Rear Truck Ladder 1
1-30060DPM Mounting Screw for sideframe & Front Truck Ladder 10
See Diagram on opposite side for identification. Parts shown in Italics are not illustrated.
E-7 A (Dummy) Parts List Rev 10.22.08 Printed in China
Other Bachmann Toy manuals
Bachmann
Bachmann Williams BL-2 User manual
Bachmann
Bachmann Williams EP-5 User manual
Bachmann
Bachmann Williams J CLASS LOCOMOTIVE & TENDER User manual
Bachmann
Bachmann Spectrum User manual
Bachmann
Bachmann Williams SD-90 User manual
Bachmann
Bachmann Williams O-27 User manual
Bachmann
Bachmann On30 Davenport Gears Operating instructions
Bachmann
Bachmann E-Z TRACK User manual
Bachmann
Bachmann Branchline Class 03 User manual
Bachmann
Bachmann Williams O-27 ALCO DUMMY User manual
Bachmann
Bachmann Williams CLASSIC GG-1 User manual
Bachmann
Bachmann E-Z TRACK User manual
Bachmann
Bachmann Williams FA-1 User manual
Bachmann
Bachmann Williams E7A User manual
Bachmann
Bachmann Williams SD-45 DIESEL LOCOMOTIVE User manual
Bachmann
Bachmann Long Caboose User manual
Bachmann
Bachmann Branch-Line OO Scale DCC Train Set User manual
Bachmann
Bachmann Liliput L133940-59 User manual
Bachmann
Bachmann NER E1 Technical manual
Bachmann
Bachmann THUNDERBIRDS AiP10002 User manual
