Axis M1143-L User manual
INSTALLATION GUIDE
ENGLISH DEUTSCH ITALIANO ESPAÑOL
FRAN
Ç
AIS
AXIS M1143-L Network Camera
AXIS M1144-L Network Camera
Legal Considerations
Video and audio surveillance can be prohibited
by laws that vary from country to country. Check
the laws in your local region before using this
product for surveillance purposes.
These network cameras include one (1) H.264
decoder license. To purchase further licenses,
contact your reseller.
Electromagnetic Compatibility (EMC)
This equipment has been designed and tested to
fulfill applicable standards for:
Radio frequency emission when installed
according to the instructions and used in its
intended environment. Immunity to electrical
and electromagnetic phenomena when installed
according to the instructions and used in its
intended environment.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures: Re-orient or relocate
the receiving antenna. Increase the separation
between the equipment and receiver. Connect
the equipment to an outlet on a different circuit
to the receiver. Consult your dealer or an
experienced radio/TV technician for help.
Shielded (STP) network cables must be used with
this unit to ensure compliance with EMC
standards. See
Electromagnetic Compatibility
(EMC),
on page 85 for more information on this
product’s compliance with safety standards.
Equipment Modifications
This equipment must be installed and used in
strict accordance with the instructions given in
the user documentation. This equipment
contains no user-serviceable components.
Unauthorized equipment changes or
modifications will invalidate all applicable
regulatory certifications and approvals.
Liability
Every care has been taken in the preparation of
this document. Please inform your local Axis
office of any inaccuracies or omissions. Axis
Communications AB cannot be held responsible
for any technical or typographical errors and
reserves the right to make changes to the
product and documentation without prior
notice. Axis Communications AB makes no
warranty of any kind with regard to the material
contained within this document, including, but
not limited to, the implied warranties of
merchantability and fitness for a particular
purpose. Axis Communications AB shall not be
liable nor responsible for incidental or
consequential damages in connection with the
furnishing, performance or use of this material.
RoHS
This product complies with both the
European RoHS directive, 2002/95/EC,
and the Chinese RoHS regulations,
ACPEIP.
WEEE Directive
The European Union has enacted a
Directive 2002/96/EC on Waste
Electrical and Electronic Equipment
(WEEE Directive). This directive is
applicable in the European Union member
states.
The WEEE marking on this product (see right) or
its documentation indicates that the product
must not be disposed of together with
household waste. To prevent possible harm to
human health and/or the environment, the
product must be disposed of in an approved and
environmentally safe recycling process. For
further information on how to dispose of this
product correctly, contact the product supplier,
or the local authority responsible for waste
disposal in your area.
Business users should contact the product
supplier for information on how to dispose of
this product correctly. This product should not
be mixed with other commercial waste. For more
information, visit www.axis.com/techsup/.
Support
Should you require any technical assistance,
please contact your Axis reseller. If your
questions cannot be answered immediately, your
reseller will forward your queries through the
appropriate channels to ensure a rapid response.
If you are connected to the Internet, you can:
• download user documentation and firmware
updates
• find answers to problems in the FAQ database.
Search by product, category, phrases.
• report problems to Axis support by logging in
to your private support area.
Safeguards
Please read through this Installation Guide carefully before installing the product.
Keep the Installation Guide for further reference.
CAUTION!
• When transporting the Axis product, use the original packaging or equivalent
to prevent damage to the product.
• Store the Axis product in a dry and ventilated environment.
• Avoid exposing the Axis product to vibration, shocks or heavy pressure and do
not install the camera on unstable brackets, unstable or vibrating surfaces or
walls, since this could cause damage to the product.
• Only use hand tools when installing the Axis product, the use of electrical
tools or excessive force could cause damage to the product.
• Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth
for cleaning.
• Use only accessories that comply with technical specification of the product.
These can be provided by Axis or a third party.
• Use only spare parts provided by or recommended by Axis.
• Do not attempt to repair the product by yourself, contact Axis or your Axis
reseller for service matters.
IMPORTANT!
• This Axis product must be used in compliance with local laws and regulations.
Battery replacement
This Axis product uses a 3.0V CR2032 Lithium battery as the power supply for its
internal real-time clock (RTC). Under normal conditions this battery will last for a
minimum of 5 years. Low battery power affects the operation of the RTC, causing it
to reset at every power-up. A log message will appear when the battery needs
replacing. The battery should not be replaced unless required!
If the battery does need replacing, please contact www.axis.com/techsup for
assistance.
• Danger of Explosion if battery is incorrectly replaced.
• Replace only with the same or equivalent battery, as recommended by the
manufacturer.
• Dispose of used batteries according to the manufacturer's instructions.
AXIS M1143-L/M1144-L Page 5
ENGLISH
AXIS M1143-L/M1144-L Network Camera
Installation Guide
This guide helps you to install the AXIS M1143-L/M1144-L Network
Camera on your network. For further information, please see the User
Manual available on www.axis.com/techsup
Installation steps
1. Check the package contents against the list below.
2. Hardware overview on page 6.
3. Install the hardware on page 7.
4. Assign an IP address on page 8.
5. Set the password on page 11.
6. Adjust image and focus on page 13
Package contents
Item Title/Variants
Network camera AXIS M1143-L
AXIS M1144-L
Camera stand
Terminal block
connector
4-pin connector block for connecting external
devices to the I/O terminal connector
Accessory Lever tool
CD AXIS Network Video CD, including installation
tools and other software.
Printed material AXIS M1143-L/M1144-L Installation Guide
Warranty document
Important!
This product must be used
in compliance with local
laws and regulations.
Page 6 AXIS M1143-L/M1144-L
Hardware overview
Dimensions (HxWxD)
AXIS M1143-L/AXIS M1144-L: 46 x 75 x 115 mm (1.8" x 3.0" x 4.5")
Focus puller
Zoom puller
micro SD
card slot
I/O connector Network connector (PoE)
Control button
Camera stand
Network, status, power LEDs
Light sensor
AXIS M1143-L/M1144-L Page 7
ENGLISH
LED indicators
Install the hardware
1. Attach the stand to the camera by screwing it on. For wall
mounting, attach the stand to wall first, using 3 appropriate screws.
2. Attach the cable to the network connector (supports PoE class 2) in
the camera.
3. Check that the indicator LEDs indicate the correct conditions. See
table above.
Note: Make sure the light sensor is not covered; this could affect its
performance and lead to false Day/Night shifts.
LED Color Indication
Network Green Steady for connection to a 100 Mbit/s network. Flashes
for network activity.
Amber Steady for connection to 10 Mbit/s network. Flashes for
network activity.
Unlit No network connection.
Status Green Steady green for normal operation.
Note: Configure the Status LED to be unlit during normal
operation, or to flash only when the camera is accessed
from Setup > System Options > LED. See the online help
files for more information.
Amber Steady during startup, reset to factory default or when
restoring settings.
Red Slow flash for failed upgrade.
Power Green Normal operation.
Amber Flashes green/amber during firmware upgrade.
Page 8 AXIS M1143-L/M1144-L
Assign an IP address
Most networks today have a DHCP server that automatically assigns IP
addresses to connected devices. If your network does not have a DHCP
server, the Network Camera will use 192.168.0.90 as the default IP
address.
AXIS IP Utility and AXIS Camera Management are the recommended
methods for setting an IP address in Windows. These free applications
are available on the Axis Network Video Product CD supplied with this
product, or they can be downloaded from www.axis.com/techsup
Depending on the number of cameras you wish to install, use the
method that suits you best.
Notes:
• If assigning the IP address fails, check that there is no firewall blocking the
operation.
• For other methods of assigning or discovering the IP address of the AXIS
M1143-L/M1144-L, such as in other operating systems, see page 14.
Method Recommended for Operating system
AXIS IP Utility
See page 9
Single camera
Small installations
Windows
AXIS Camera
Management
See page 10
Multiple cameras
Large installations
Installation on a different
subnet
Windows 2000
Windows XP Pro
Windows 2003 Server
Windows Vista
Windows 7
AXIS M1143-L/M1144-L Page 9
ENGLISH
AXIS IP Utility - single camera/small installation
AXIS IP Utility
automatically
discovers and displays
Axis devices on your
network. You can also
manually set a static IP
address through this application. AXIS IP Utility is available on the Axis
Network Video Product CD, or it can be downloaded from www.axis.com/
techsup
Install the AXIS M1143-L/M1144-L Network Camera on the same
network segment (physical subnet) as the computer running AXIS IP
Utility.
Automatic discovery
1. Check that the AXIS M1143-L/M1144-L Network Camera is
connected to the network and that power has been applied.
2. Start AXIS IP Utility.
3. When the AXIS M1143-L/M1144-L network camera appears in the
window, double-click to open the camera’s home page.
4. See page 11 for instructions on how to set the password.
Set the IP address manually (optional)
1. Acquire an unused IP address on the same network segment your
computer is connected to.
2. Select the AXIS M1143-L/M1144-L in the list.
3. Click the button Assign new IP address to selected device and
enter the IP address.
4. Click the Assign button and follow on-screen instructions. Note
that the camera must be restarted within two minutes for the new
IP address to be set.
5. Click the Home Page button to access the camera’s web pages.
Page 10 AXIS M1143-L/M1144-L
6. See page 11 for instructions on how to set the password.
AXIS Camera Management - multiple cameras/large installa-
tions
AXIS Camera Management can automatically discover multiple Axis
devices, show connection status, manage firmware upgrades and set IP
addresses.
Automatic discovery
1. Check that the camera is connected to the network and that power
has been applied.
2. Start AXIS Camera Management. When the camera appears in the
window, right-click the link and select Live View Home Page.
3. See page 11 for instructions on how to set the password.
Assign an IP address in a single device
1. Select the network camera in AXIS Camera Management and click
the Assign IP button .
2. Select Assign the following IP address and enter the IP address,
subnet mask and default router the device will use.
3. Click the OK button.
Other manuals for M1143-L
3
This manual suits for next models
1
Table of contents
Languages:
Other Axis Security Camera manuals
Axis
Axis Q3538-SLVE User manual
Axis
Axis Axis 211 User manual
Axis
Axis M42 Series User manual
Axis
Axis P1311 User manual
Axis
Axis M1135-E Mk II User manual
Axis
Axis Q8685-E User manual
Axis
Axis NETWORK CAMERA 2100 User manual
Axis
Axis Q6215-LE User manual
Axis
Axis Q6034 PTZ User manual
Axis
Axis Q1755-E User manual
