Axis 233D User manual

ENGLISH FRANCAIS DEUTSCH ESPAÑOL

ITALIANO

AXIS 233D

Network Dome Camera

Installation Guide

AXIS 233D Installation Guide Page 3

ENGLISH

AXIS 233D

Installation Guide

This installation guide provides instructions for installing the AXIS 233D Network Dome

Camera on your network. For all other aspects of using the product, please see the User’s

Manual, available on the CD included in this package, or from www.axis.com/techsup

Installation steps

1. Check the package contents against the list

below.

2. Install the hardware. See page 4.

3. Assign an IP address. See page 11.

4. Set the password. See page 14.

Package contents

Before you begin:

If the AXIS 233D is to be mounted in a position where it is difficult to

access, it is recommended that you set the IP address and get the camera up

and running before completing the hardware installation.

Item Models/variants/notes

Network dome camera AXIS 233D

Indoor Power Supply with

power cable

Europe

Australia

USA/Japan

Korea

Terminal block connectors 3 (8-pin) connector blocks for connecting external devices to the I/O terminal

connectors

Mounting kit Hard Ceiling Mount for Indoor Use

Drop Ceiling Mount for Indoor Use

CD AXIS Network Video Product CD, including product documentation, installa-

tion tools and other software

Printed Materials AXIS 233D Installation Guide (this document)

Axis Warranty Document

Important!

This product must be used in

compliance with local laws

and regulations.

Page 4 AXIS 233D Installation Guide

Install the Hardware

Place dome bubble on camera

1. Place dome bubble on the camera

base.

2. Place black ring with coordinates

over dome. Turn ring till it comes

into the slots.

3. Different screws are used for

fastening the black ring depending

on which ceiling mount is being

installed.(See figure to right)

4. Tighten screws to hold ring and

dome securely. Follow instructions

for your chosen camera mounting.

Dimensions

HxWxD = 209 x 170 x 170 mm (8.23” x

6.69” x 6.69”)

Weight = 2.5Kg (5.5 lbs) excluding power

supply

Status LED

Black

Red

Control button

Restart button

Top

Drop Ceiling Mount use 3 M3x10 screws.

Hard Ceiling Mount use 3 Recessed screws

(do not tighten screws completely)

Note:

The camera’s serial number (S/N) is on

this label. You will need this number to

with this product. Put it in a safe place

for future reference.

set the camera’s IP address.

There is an additional label included

AXIS 233D Installation Guide Page 5

ENGLISH

Ceiling Mounts Package Contents

Hard Ceiling Mount

Drop Ceiling Mount

1 Inner bracket

1 Outer bracket 1 Decoration ring

5 M3x10 screws

4 M3x60 screws

1 Hard ceiling bracket

1 Decoration ring

4 plugs

4 ST4.2 screws

2 M3x10 screws

4 M4x10 screws

3 Recessed screws

Page 6 AXIS 233D Installation Guide

Hard Ceiling Mount

Attach bracket to ceiling using

4 ST4.2 screws and plugs.

Attach safety wire to bracket

and base of dome using an

Slot for cables

Insert 2 M4 screws in

each side of base

Insert network camera

into ceiling bracket

Slide on decoration ring

Captive screw

M4 screw & nut.

AXIS 233D Installation Guide Page 7

ENGLISH

Referring to the image for Hard Ceiling Mount, follow these instructions to mount the dome

camera:

1. Secure the bracket to the ceiling with four ST4.2 screws and plugs. (Figure A)

2. Attach one end of the safety wire to the bracket and the other end to the AXIS 233D

using an M4 screw and nut. (Figure B)

3. Insert four M4 screws (2 screws on each side) partially into the camera base.(Figure

4. Insert the AXIS 233D into the bracket and tighten the captive screw allowing you to

free your hands to tighten the four screws in the screw slots (two on each side) on the

AXIS 233D.(Figure D)

5. Connect the network cable.

6. Connect the power cable to the connection block (see Power connections, on page

10)

7. Slide the decoration ring on to the AXIS 233D and lock into place by tightening two

M3 screws into the bracket. Take care to place the side with the open slot over the

connection blocks for cables.(Figure E)

8. The hardware installation is now complete, proceed to Assign an IP address, on page

11 to install the AXIS 233D on your network.

Page 8 AXIS 233D Installation Guide

Drop Ceiling Mounting

Attach ceiling mount brackets

with 4 long M3 screws.

Attach safety wire

Attach decorative ring

with 2 M3 screws

Inner mounting ring

Outer mounting ring

with an M4 screw & nut

AXIS 233D Installation Guide Page 9

ENGLISH

Referring to the image for Drop Ceiling Mount, follow these instructions to mount the dome

camera:

1. Locate the position in the ceiling for a 190mm hole to be cut. A template is included

to aid in marking the mounting hole.

2. Cut the hole in the ceiling according to the markings.

3. Insert the inner mounting ring in the ceiling with the screw guides pointing

down.(Figure A)

4. With four long M3 screws, attach inner mounting ring to the outer mounting ring.

5. Attach the safety wire to something structurally strong in the ceiling and to the base

of the camera using an M4 screw and nut.(Figure B)

6. Through the hole in the ceiling connect the Ethernet cable and the power cable to

the connection block (see Power connections, on page 10).

7. Push the dome body up into the installed bracket taking care to align the screw holes

in body (see step 3, on page 4) with the mounting bracket’s screw slots. Tighten

screws to lock camera into the bracket.

8. Slip the decoration ring over the dome aligning screw holes with screw slots in

bracket. Use 2 M3 screws to fasten the decoration ring.(Figure C)

9. The hardware installation is now complete, proceed to Assign an IP address, on page

11 to install the AXIS 233D on your network.

Page 10 AXIS 233D Installation Guide

Power connections

Power can be supplied to the camera by the following methods:

• Connect the supplied indoor power adapter to the power connector block and

attach it to the camera casing. Note that this indoor power adapter provides

power for the camera only.

• Connect an outdoor power supply to the power connector block and attach it to

the camera casing. For information on available outdoor power supplies, please

visit the Support pages at http://www.axis.com/techsup/

The power connector block supports both AC and DC input power.

Power connector block pin assignment table

Pin Function

1AC AXIS PS-R (or 22-40 VDC)

max 20W power consumption.

-or-

AXIS PS-24 (or 18-30 VAC)

max 25VA power consump-

tion

2ACorDC+

3 GND/DC-

4Ext.Vout=12V/

200mA

Note:

For information about

connecting auxiliary

power and audio see

Unit connectors, on

page 17.

5-8 Audio

GND/DC-

Power/Audio

12 3

AC/DC+

Other manuals for 233D

Table of contents

Languages:

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

Lumens

Lumens VC-A50PNW installation guide