Avigilon H6SL Series User manual

IP Camera Web Interface

User Guide

Avigilon High Definition H6, H5, and H4 IP Camera Models:

H6SL-xx H6M-Dx-IR H5EX-xx-BO1 H4A-ETD-KIT

H5A-xx H6M-Dx H5EX-xx-CO1 H4A-THC-BO

H5A-xx-IR H5A-CR1-IR-xx H4A-xx(-B) H4A-G-B(-B)

H5SL-xx H5A-CR2-IR-xx H4M-D H3A-xx

H5SL-xx-IR H4A-G-xx-IR(-B) H4F-DO H3A-BO-IR

H5M-DO H4A-xx-IR(-B) H4SL-xx(-IR) 

AVIGILONCONTROL CENTER, ACC, ACCESS CONTROL MANAGER, and ACM are trademarks of Avigilon

Corporation. Android is a trademark of Google LLC. Apple, Safari and Mac are trademarks of Apple Inc,

registered in the US and other countries. Firefox is a registered trademark of the Mozilla Foundation in the US

and other countries. Other names or logos mentioned herein may be the trademarks of their respective

owners. The absence of the symbols ™ and ® in proximity to each trademark in this document or at all is not a

disclaimer of ownership of the related trademark. Covered by one or more claims of the patents listed at

patentlist.hevcadvance.com.

This document has been compiled and published using product descriptions and specifications available at

the time of publication. The contents of this document and the specifications of the products discussed

herein are subject to change without notice. Avigilon Corporation reserves the right to make any such

changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the

completeness or accuracy of the information contained in this document; or (2) is responsible for your use of,

or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages

(including consequential damages) caused by reliance on the information presented herein.

Avigilon Corporation

avigilon.com

PDF-H4WebUI-G

Revision: 3 - EN

20230420

Table of Contents

Introduction 1

System Requirements 1

Other Web Interface Guides 1

Accessing the Camera Web Interface 2

Creating the Initial User and Logging In 2

Logging In 3

Live View 4

Saving a Still Image 4

Setup 5

General 6

Network 7

Configuring 802.1x Port-Based Authentication 10

Switching 802.1x Authentication Profiles 10

Deleting an 802.1x Authentication Profile 10

Configuring SNMP 11

IP Filter 12

Security Settings 12

Image and Display 14

Adjustments 18

Compression and Image Rate 20

Enabling HDSMSmartCodec™ Technology Settings 21

Viewing the RTSP Stream URI 21

Accessing the Still Image URI 22

HDSMSmartCodec Technology Advanced Settings 22

Motion Detection 23

Tamper Detection 24

Analytics 24

Privacy Zones 24

Setting a Privacy Zone 25

Deleting a Privacy Zone 25

Setting a Removable Privacy Zone for Specific Users 25

Storage 26

Enabling Onboard Storage 27

ONVIFProfile G 27

Downloading Recorded Video from the Web Interface 28

iii

Downloading Recorded Video from the SD Card 28

Deleting Recorded Video 29

SD Card Failures 29

Digital Inputs and Outputs 30

Washer 31

Audio 32

Users 32

Adding a User 32

Editing Users and Passwords 33

Removing a User 33

Keeping Usernames and Passwords After Firmware Revert 33

System 34

Upgrading the Camera Firmware 34

Device Log 34

Disable WebUI 35

About 36

Checking a Camera's Power Source 36

ACC™ ES Camera 37

Checking the ACC ES Camera Status 37

Configuring the ACC ES Camera Administration Settings 37

Restarting the ACC Software 37

Formatting the Recorded Video Drive 37

Changing the Communication Ports 38

Overriding the Login Limit 38

Enabling Storage Management 38

Reviewing ACC Software Logs 39

Introduction

Avigilon High Definition IP cameras include a web interface that allows you to view the live video and

configure the camera through a web browser.

Before you access the web interface, make sure all the procedures described in the camera installation guide

have been completed.

Tip: Features and options are disabled if they are not supported by the camera.

System Requirements

The following browsers are recommended when accessing the web interface from any Windows, Mac, or

mobile device:

lMozilla Firefox version 96.0.2 (64-bit) or later

lGoogle Chrome™ version 97.0.4692.71 (64-bit, official build) or later

lMicrosoft Edge version 97.0.1072.76 (64-bit, official build) or later

Note: The web interface may work with older or unsupported browsers, but this has not been tested.

Other Web Interface Guides

Check out these other Web Interface Guides for other types of Avigilon cameras:

lPTZCamera Web Interface Guide — for pan, tilt, and zoom cameras.

lMulti-HeadCamera Web Interface Guide — for dual head and multisensor cameras.

lH4and H5 Pro Camera Web Interface Guide — for high resolution Pro cameras.

lH5AFisheye Camera Web Interface Guide — for H5A fisheye cameras.

lVideo Intercom Web Interface Guide — for H4 Video Intercoms.

lAPD Sensor Web Interface Guide — for Avigilon presence detectors.

Introduction 1

Accessing the Camera Web Interface

After the camera has been installed, you need the camera's IP address to access the web interface. The IP

address can be found in the following:

lThe Avigilon Control Center (ACC) software — Open the Setup tab to see the details of the selected

camera.

lMotorola Solutions' Camera Configuration Tool (CCT) — Go to the Network tab to see the details of the

selected cameras.

Once you have the IP address, complete the following procedure to access the web interface:

Note: The web browser must be configured to accept cookies or the camera web interface will not

function correctly.

1. On a computer with access to the same network as the camera, enter the camera's IP address into a

web browser:

http://<camera IP address>/

For example: http://192.168.1.40/

2. You will automatically be prompted to enter your username and password to access the camera. If the

device is in the factory default state and was manufactured after January 1, 2020, you will be asked to

create a user with administrator privileges before the device will be operational. For more information,

see Creating the Initial User and Logging In below.

Creating the Initial User and Logging In

Cameras manufactured after January 1, 2020, do not have a default username and password and will be in a

factory default state.

Important: You must create a user with administrator privileges before the camera is operational.

Tip: Cameras manufactured before January 1, 2020, have a default username and password you can

use to log in. For more information, see Logging In on the next page.

If the camera is in the factory default state, you will be redirected to the Add User page to create an

administrator user:

Accessing the Camera Web Interface 2

1. Enter a new User Name or keep the default administrator name.

2. Enter a new Password for the user. We recommend using a complex and unique password. Avoid

using an empty password as they are not supported across all platforms and devices.

3. Confirm the new password.

4. For the first user, Administrator must be selected in the Security Group drop-down menu.

5. Click Apply. After creating the user, you will be asked to login.

Logging In

You will automatically be prompted to enter your username and password to access the camera.

lIf the camera is in the factory default state and was manufactured after January 1, 2020, you will be

asked to create a user with administrator privileges before the camera will be operational. Use these

credentials when logging in.

lThe default username for most cameras is administrator with no password.

Tip: It is recommended that you add a password after your first login. For more information, see

Editing Users and Passwords on page33.

Logging In 3

Live View

After you log in, the first page you see is the Live View. The Live View contains an image panel that displays

the live video stream.

Use the menu links in the top-left corner to navigate through the web interface. Click Live View any time to

return to this page.

Tip: Features and options are disabled if they are not supported by the camera.

Saving a Still Image

If you see the Save Still to SDCard button from the Live View page, the camera supports the ability to take

snapshots of live video from the web interface.

To use this feature, the following settings are required for the camera:

lThere is an SD card inserted in the camera. For more information, see the camera's installation guide.

Saving an image to the SD card is not supported if you are using FIPS Level 3 encryption with a CryptR

micro card inserted in the SD slot.

lThe camera's onboard storage settings are enabled on the Storage page. For more information, see

Storage on page26.

lThe camera's video format must be set to MJPEG in the Compression and Image Rate page. For more

information, see Compression and Image Rate on page20.

Once all the requirements have been met, you can click Save Still to SDCard and the image that is displayed

in the Live View page is automatically saved to the SD card.

To download the snapshot, see Downloading Recorded Video from the Web Interface on page28.

Live View 4

Setup

Note: Certain options are not displayed if they are not supported by the camera model you are using

or if you do not have the required user permissions.

The factory default settings allow you to use the camera or encoder immediately after installation. If you have

special requirements, you can customize the settings through the web interface. In the top-left menu area,

click Setup to display all the available setup pages.

A Restore Defaults button is available on each setup page to restore the factory default settings.

Be aware that some settings are only available through the camera's web interface and cannot be changed in

the network video management software.

For information specific to H4 Edge Solution (ES) cameras, see ACC™ ES Camera on page37.

For settings that are specific to the H4 Thermal Elevated Temperature Detection cameras, see the H4

Thermal Elevated Temperature Detection Camera User Guide.

Setup 5

General

When you select Setup, the first page you see is the General page. The General page allows you to set the

camera's identity.

Tip: Features and options are disabled if they are not supported by the camera.

Note: If a camera with video analytics or unusual motion detection is physically moved or adjusted,

or if the focus or zoom level is changed, reset the learning progress to provide accurate results. If the

camera's image rate and compression or display settings are updated, the learning progress may

reset automatically.

1. In the Name field, give the camera a meaningful name.

2. In the Location field, describe the camera's location.

3. Select the Disable device status LEDs check box to disable the LED indicators located on the camera.

4. Select the Lens Distortion Correction check box to enable an algorithm-based automatic correction

of lens distortion. The camera will reboot when applying this setting.

5. From the Mode drop-down list, select the mode that the camera will operate in.

This option is only displayed for higher bandwidth usage cameras.

lFull Feature — This is the standard operating mode. Offers the full functionality of the camera.

lHigh Framerate — This mode will use the maximum image rate possible but will disable self-

learning video analytics, Unusual Motion Detection (UMD), and tamper detection and WDR on

EScameras.

Models Features Impacted by High Framerate

4K (8 MP) H4 HD Analytic

Cameras:

8.0-H4A-x

oIncreased maximum frame rate

oSelf-learning video analytics and tamper disabled

oUnusual Motion Detection (UMD) disabled

oLower resolution tertiary video stream

oSecondary video stream disabled

H4 HD ES Analytic Cameras:

xx-H4A-xG-x

oIncreased maximum frame rate

oWDR disabled

General 6

This manual suits for next models

Table of contents

Other Avigilon Security Camera manuals

Avigilon

Avigilon H6M-D User manual

Avigilon

Avigilon 1.0-H3M-DO1 User manual

Avigilon

Avigilon 1.0-H3M-DC1 User manual

Avigilon

Avigilon 8.0MP-HD-DOME-360 User manual

Avigilon

Avigilon 1.0W-H3-BO1-IR User manual

Avigilon

Avigilon 2.0C-H6A-BO1-IR User manual

Avigilon

Avigilon H5A User manual

Avigilon

Avigilon 1.0W-H3-BO1-IR User manual

Avigilon

Avigilon 12W-H3-4MH-DP1 User manual

Avigilon

Avigilon H4A-G-BO1-IR User manual

Avigilon

Avigilon 1.0-H3-D1-IR User manual

Avigilon

Avigilon 1.3C-H4SL-BO1-IR User manual

Avigilon

Avigilon H4SL-D User manual

Avigilon

Avigilon 2.0C-H5A-BO1-IR User manual

Avigilon

Avigilon 5.0-H3-DP2 User manual

Avigilon

Avigilon 1.0-H3M-DO1 User manual

Avigilon

Avigilon 1.0-H3-D1 User manual

Avigilon

Avigilon H3-3MH-DC1 User manual

Avigilon

Avigilon 1.0C-H4PTZ-DC45 User manual

Avigilon

Avigilon H3-BO1-IR User manual

Avigilon

Avigilon 1.3C-H4SL-D1 User manual

Avigilon

Avigilon H4A-DO1, H4A-DO1-IR, H4A-DO2, H4A-G-DO1-IR User manual

Avigilon

Avigilon 1.0C-H4A-B1 User manual

Avigilon

Avigilon 12W-H3-4MH-DO1-B User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications