Autonics SPC1 Series User manual
I-50
SPC1 Series
Specications
Features
Single-Phase, Power Controller
● Various and simple input specication
• DC4-20mA, 1-5VDC, External 24VDC
• External adjuster (1kΩ)
• External contact (ON/OFF)
● Various function
• OUT ADJ (output limit) function
•
SOFT START function (except for ON/OFF control method)
• OUT display function
• 50/60Hz automatic converting function
● Various control method by switch
• Phase control method
• Cycle control method (zero cross turn-on)
• ON/OFF control method (zero cross turn-on)
Ordering Information
Rated load current
Marking language
Item
SPC 35 E1 - -
35 35A
50 50A
EEnglish
1Single-phase
SPC Solid state power controller
Control phase
Model SPC1-35-E SPC1-50-E
Power supply 220VACᜠ50/60Hz
Allowable voltage range 90 to 110% of rated voltage
Operating frequency uctuation
±1Hz
Rated load current 35A (single-phase) 50A (single-phase)
Control power 220VACᜠ
Control range Phase control: 0 to 98%, Cycle control: 0 to 100%
Applied load Resistance load (min. load: over 5% of rated current)
Cooling method Natural cooling
Control circuit Micom control type
Control input • 1-5VDCᜡ • DC4-20mA (250Ω) • ON/OFF (external relay contact or 24VDCᜡ)
• External adjuster (1kΩ) • Output limit input (front OUT ADJ. adjuster)
Control
method
By selection
switch
• Phase control※1
• Cycle control (zero cross turn-on) - Period 0.5 sec, 2.0 sec, 10 sec ※1
• ON/OFF control (zero cross turn-on)
Starting type SOFT START (0 to 50 sec variable)
Indicator Output indicator (OUT): red LED
Insulation resistance Over 100MΩ (at 500VDC megger)
Dielectric strength 2000VAC 50/60Hz for 1minute
Noise immunity ±2kV the square wave noise (pulse width: 1us) by the noise simulator
Vibration Mechanical
0.75mm amplitude at frequency of 10 to 55Hz (for 1 min) in each X, Y, Z direction for 1 hour
Malfunction
0.5mm amplitude at frequency of 10 to 55Hz (for 1 min) in each X, Y, Z direction for 10 min
Shock Mechanical 300m/s² (approx. 30G) in each X, Y, Z direction for 3 times
Malfunction 100m/s² (approx. 10G) in each X, Y, Z direction for 3 times
Environment
Ambient temp. 0 to 50℃, storage: -25 to 65℃
Ambient humi. 35 to 85%RH, storage: 35 to 85%RH
Wire specication
AWG16 to 8 AWG8 to 6
Unit weight Approx. 1kg
※1: Refer to ' Operation and Function'.
※Environment resistance is rated at no freezing or condensation.
Please read “Safety considerations” in operation
manual before using.
SPC1 Series
I-51
Single-Phase, Power Controller
(A)
Photoelectric
Sensors
(B)
Fiber
Optic
Sensors
(C)
Door/Area
Sensors
(D)
Proximity
Sensors
(E)
Pressure
Sensors
(F)
Rotary
Encoders
(G)
Connectors/
Connector Cables/
Sensor Distribution
Boxes/Sockets
(H)
Temperature
Controllers
(I)
SSRs / Power
Controllers
(J)
Counters
(K)
Timers
(L)
Panel
Meters
(M)
Tacho /
Speed / Pulse
Meters
(N)
Display
Units
(O)
Sensor
Controllers
(P)
Switching
Mode Power
Supplies
(Q)
Stepper Motors
& Drivers
& Controllers
(R)
Graphic/
Logic
Panels
(S)
Field
Network
Devices
(T)
Software
Dimensions
F.G.
F.G.
F.G. +5V
+5V
+5V
IN
IN
IN
IN
IN
IN
GND
GND
(+)
(+)
(-)
(-)
GND
Sensor or other
controlling equipment
Sensor or other
controlling equipment
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
External contact
or switch
DC4-20mA
1-5VDC
※This function must not be used in ON/OFF control method.
※This function must not be used in ON/OFF control method.
※
It is available for all control methods.
OUT ADJ and SOFT START functions are not available
in ON/OFF control method.
● Spacing
※ When installing multiple power controllers,
please keep space at least 30mm in
horizontal and 100mm in vertical between
power controllers for heat radiation.
(unit: mm)
Connections
1. External connection
2. Connection of control input terminals
1) DC4-20mA control input
It controls 0 to 100% when you apply DC4-20mA on ④, ⑤ terminals when power is applied.
2) 1-5VDC control input
It controls 0 to 100% when you apply 1-5VDC on ③, ⑤ terminals when power is applied.
3) ON/OFF external contact control input
It controls 100% if you connect external contact or switch to ②, ③ terminal when it is ON, it controls 0% when it is OFF.
(resistive load only)
F.G.
Rapid fuse
(external
attachment)
+5V IN
1
RTW U
2 3 4 5
IN 0V
SOURCE
220VAC
50/60Hz
LOAD
136.9
93.2
37.294.6
124.8
108
2-Ø4.2
2-M4
30
108
100
100
100
I-52
SPC1 Series
F.G.
F.G. +5V
+5V
IN
IN
IN
+
24VDC
-
IN
GND
GND
②
① (min.)
(max.) ③
1
2
3
45
6
7
9
8
11
10
12
1. Case
2. Terminal block cover
3. Terminal block for control input
4. Terminal block of the power
5. Terminal block for load connection
6. Output indicator (OUT)
7. Control method selection switch
8. SOFT START setting adjuster
9. Output limit setting adjuster
10. Selection jumper of control period
11. Selection jumper of control mode
12. Panel mounting hole
(bolt size: M4×50mm)
※
10, 11 are placed on the inner PCB of the
product.
12
1 2 3 4 5
1 2 3 4 5
External adjuster 1kΩ
※This function must not be used in ON/OFF control method.
※
It is available for all control methods.
OUT ADJ and SOFT START functions are not available
in ON/OFF control method.
4) External adjuster control input
After power is applied, connecting the external adjuster 1㏀to ②, ③ and ⑤ terminals and turning adjuster control from 0%
to 100%.
It is available to control as OUT ADJ, adjuster for the above 1), 2), 3) and set at 100% when it is not used.
5) External 24VDC control input
It can be used with external 24VDC voltage as below.
It is available to control of ON/OFF, outputs 100% for applying 24VDC and 0% for applying 0VDC.
Unit Description
Factory Default
Control method Phase control
Control mode Phase equal division type according to control input
Control cycle period 0.5 sec (JP1, JP2 short)
SOFT START setting 0 sec
OUT ADJ. setting 100%
※Tighten the terminal screw with the below tightening torque.
Terminal type Signal input
(control input) Output and power
Screw M3.5 M5
Tightening torque 0.6 to 1.2N.m 1.5 to 2.2N.m
a b
<Round>
Terminal
type
Signal input
(control input)
Output and
power
a Min. 3.5mm Min. 5mm
b Max. 7.0mm Max. 12mm
※Use terminals of size specied below.
I-53
Single-Phase, Power Controller
(A)
Photoelectric
Sensors
(B)
Fiber
Optic
Sensors
(C)
Door/Area
Sensors
(D)
Proximity
Sensors
(E)
Pressure
Sensors
(F)
Rotary
Encoders
(G)
Connectors/
Connector Cables/
Sensor Distribution
Boxes/Sockets
(H)
Temperature
Controllers
(I)
SSRs / Power
Controllers
(J)
Counters
(K)
Timers
(L)
Panel
Meters
(M)
Tacho /
Speed / Pulse
Meters
(N)
Display
Units
(O)
Sensor
Controllers
(P)
Switching
Mode Power
Supplies
(Q)
Stepper Motors
& Drivers
& Controllers
(R)
Graphic/
Logic
Panels
(S)
Field
Network
Devices
(T)
Software
1.
SOFT START setting adjuster (0 to 50 sec)
2. Output limit setting adjuster (0 to 100%)
3. Output indicator
4. Control method selection switch
PHASE: Phase control method
CYCLE: Cycle control method
ON/OFF: ON/OFF control method
123
4
※When selecting cycle control method, the cycle has been set as 0.5 sec. It can be changed to 2 sec, 10 sec by selection.
※The contorl method setting cannot be changed wwhile it is operating. Turn OFF the power at rst then change the
setting and supply the power again.
※To change the control mode, change TP3 of PCB as below.
Operation and Function
Front
Control method selection
1) Phase control
It is output type to control phase of an alternating signal according to control input signal.
2) Cycle control (xed cycle) - Zero cross turn-on
It controls the power, which is applied into the load to repeat ON/OFF cycle like below picture with constant proportion
according to control input signal. It is easy to control the load and there is no ON/OFF noise because it turns ON and OFF
at the zero point of AC.
Usually it is used in a place or electric furnace which is not easily effected by external noise.
●
Equal division type of phase according as control input
This is analog type to output control angle with dividing
equally according as control input signal. It shows power
characteristic as (Fig. 1) and it might occur over power and
lack power at point middle of control input.
●
Equal division type of power according as control input
It divides control angle non-equally according as control
input signal then make power curve linearization, so it
becomes possible to output the power, which is proportioned
control input as outputting (Fig. 1).
Control
method Phase control Cycle control
(zero cross turn-on)
ON/OFF control
(zero cross turn-on)
Switch
JP3 Division method (control mode)
SHORT Equal division of phase according as control input
OPEN Equal division of power according as control input
Control input Control input
(Fig. 1) (Fig. 2)
Voltage curve
Power curve
Output Output
1VDC
DC4mA
1VDC
DC4mA
PHASE PHASE PHASE
ON/OFF ON/OFF ON/OFF
CYCLE CYCLE CYCLE
5VDC
DC20mA
5VDC
DC20mA
100% 100%
100% 100%
0% 0%
※SHORT OPEN
Voltage curve
Power curve
I-54
SPC1 Series
JP1 JP2 Cycle (sec)
SHORT SHORT 0.5sec
SHORT OPEN 2.0sec
OPEN SHORT 10sec
OPEN OPEN × (not used)
※To change control cycle, please change JP1 and JP2 of PCB as below.
OUT ADJ. (output limit) (0 to 100%)
This function will be [Control input (%) × OUT ADJ. (%) =
Output] and it controls the power supplied into the load.
Although control input is 100% (5V or 20mA), the output is
the 50% which is proportioned with OUT ADJ. When not
using OUT ADJ. function, please make set value 100%.
※This function must not be used in ON/OFF control
method.
SOFT START (0 to 50 sec)
This function protects the load in cases that the set
temperature is high, such as controlling the load (platinum.
molybdenum, tungsten, infrared lamp, etc.) in which inrush
current ows when power is supplied, or showing large
width of temperature rise during initial operation.
SOFT START set time (T) is the required time that output
reaches to 100%, and it is differentiated by OUT ADJ.
set value. For example, SOFT START is set as 10sec
and OUT ADJ. is set as 70%, it takes 7 sec to reach goal
output.
[Set time (T)×OUT ADJ. set value (%)=10 sec×0.7=7 sec]
If increasing the OUT ADJ. before output reaches to
goal output, it delays as much as the value, multiply of
increased value (%) and SOFT START set time. When not
using SOFT START function, please make set value 0.
※This function must not be used in ON/OFF control
method.
OUT display
This is LED lamp to display the status of output and will be getting brighter according as output.
(0%: min. LED light, 100%: max. LED light)
3) ON/OFF control-Zero cross
This function is when control input is ON, output is 100%.
When it is OFF, output is 0%.
It is the same function as SSR (Solid State Relay).
(It always turns ON/OFF at zero point of AC.)
※OUT ADJ. and SOFT START function are not
available in ON/OFF control method.
0%
T/2
T
50% 100%
< Output wave form of ON/OFF control >
<The output characteristic of OUT ADJ. and control input>
Control input
Control
input
Time
When OUT ADJ
is 50%
The output which
is applied into the
load is 50%
T: SOFT START setting time
※T: Time to get the output which is applied into the load is
100%.
T/2: Time to get the output which is applied into the load
is 50%.
The output which
is applied into the
load is 100%
When OUT ADJ
is 100%
ON
Output
Output
Output
100%
100%
75%
50%
50%
0
25%
OFF
100%
0%
※SHORT OPEN
When control input signal is 0% (DC4mA, 1VDC) When control input signal is 25% (DC8mA, 2VDC)
T: Cycle (0.5sec)
T: Cycle (0.5sec)
When control input signal is 50% (DC12mA, 3VDC)
When control input signal is 100% (DC20mA, 5VDC)
T: Cycle (0.5sec) T: Cycle (0.5sec)
I-55
Single-Phase, Power Controller
(A)
Photoelectric
Sensors
(B)
Fiber
Optic
Sensors
(C)
Door/Area
Sensors
(D)
Proximity
Sensors
(E)
Pressure
Sensors
(F)
Rotary
Encoders
(G)
Connectors/
Connector Cables/
Sensor Distribution
Boxes/Sockets
(H)
Temperature
Controllers
(I)
SSRs / Power
Controllers
(J)
Counters
(K)
Timers
(L)
Panel
Meters
(M)
Tacho /
Speed / Pulse
Meters
(N)
Display
Units
(O)
Sensor
Controllers
(P)
Switching
Mode Power
Supplies
(Q)
Stepper Motors
& Drivers
& Controllers
(R)
Graphic/
Logic
Panels
(S)
Field
Network
Devices
(T)
Software
Proper Usage
Temperature Derating Curve
1. Follow instructions in 'Cautions during Use'. Otherwise, it may cause unexpected accidents.
2. Use the product, after 3 sec of supplying power.
3. Before use, set the mode and function according to the specication.
Especially, be cautious that the product does not operate when OUT ADJ. is set to 0%.
Since mode/parameter can not be changed during operation, set the mode and function after turning off the power.
4. To ensure the reliability of the product, install the product on the panel or metal surface vertically to the ground.
5. Install the unit in the well ventilated place.
6. While supplying power to the load or right after turning off the power of the load, do not touch the body and heat sink.
Failure to follow this instruction may result in a burn due to the high temperature.
7. Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting the power.
8. Do not wire to terminals which are not used.
9. The rapid fuse must be connected between R terminal and the power source.
10. Do not use near the equipment which generates strong magnetic force or high frequency noise.
11. This unit may be used in the following environments.
①Indoors (in the environment condition rated in 'Specications')
②Altitude max. 2,000m
③Pollution degree 2
④Installation category III
E.g. 1) When controlling by limiting the power at ON/OFF
in phase control and cycle control method.
For example, if it needs to control 80% output when
it is ON, 24% output when it is OFF, please keep
below.
Firstly set OUT ADJ. as 80% and connect external
adjuster and external relay contact switch as the
gure then set external adjuster as 30%.
● When the External contact signal is ON
: 100% (contact input)×80% (OUT ADJ.)=80%
● When the External contact signal is OFF
: 30% (adjuster input)×80% (OUT ADJ.)=24%
E.g. 2) This is how to control 0 to 100% without
external adjuster in phase control and cycle
control method.
It is possible to control 0 to 100% by turning
OUT ADJ. in state of connecting terminal 2
and terminal 3.
Cautions during use
Applications
SPC1-35-E SPC1-50-E
<Control input terminal connection>
F.G. +5V IN IN GND
12345
<Control input terminal connection>
F.G. +5V IN IN GND
12345
External
adjuster 1kΩ
Load current [A]
Ambient temperature [℃]
0
40
30
50
20
10
010 20 30 40 50
Load current [A]
Ambient temperature [℃]
0
40
30
50
20
10
010 20 30 40 50
Remove of Case
When using the tool, be careful not to injure yourself.
After disconnecting all power sources supplied to the product,
remove the case.
Push the Joint part (4 points) on the right and left side of the case
with the at head screwdriver, and disassemble the case.
This manual suits for next models
2
Table of contents
Other Autonics Controllers manuals
Autonics
Autonics TZN4S Series User manual
Autonics
Autonics 1-Axis High Speed Stand-Alone Series User manual
Autonics
Autonics TZN Series User manual
Autonics
Autonics PA10 Series User manual
Autonics
Autonics TZ Series User manual
Autonics
Autonics TM2-22RB User manual
Autonics
Autonics PMC-2HS Series User manual
Autonics
Autonics DPU1 Series User manual
Autonics
Autonics TZN Series User manual
Autonics
Autonics TZ4SP User manual
Autonics
Autonics SPC Series User manual
Autonics
Autonics SFC-R Series User manual
Autonics
Autonics PMC-1 HS User manual
Autonics
Autonics SPR3 Series User manual
Autonics
Autonics SPR1 Series Use and care manual
Autonics
Autonics MD5-HD14 User manual
Autonics
Autonics SFC Series User manual
Autonics
Autonics TM-XGT User manual
Autonics
Autonics MD5-HF14 Series User manual
Autonics
Autonics TC3YT Series User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
