AURATON 2020 User manual
AURATON 2020
AURATON 2020 TX RX Plus
Preliminary notes
The manual includes the information on AURATON 2020
and AURATON 2020 TX RX Plus controllers.
Operation of both the controllers is identical; therefore the
whole information is placed in a single chapter. The
information related to their installation is placed in separate
sections of the manual.
AURATON 2020 TX Plus enables independent
modification of the protection code of the RX receiver
communication.
The controller is programmed in the factory to 085
code number. Nevertheless, if any communication
problem arises or another wireless temperature
controller set operates in the neighbourhood, the code
should be changed in accordance with the instruction
at page 51.
I
0
AURATON 2020AURATON 2020
AURATON 2020 TX RX Plus
31 EN AURATON 2020, AURATON 2020 TX RX Plus
1. Installation of AURATON 2020
Note: During installation of the controller the power
supply should be switched off. It is recommended to
charge a specialist company with the installation.
1.1 A choice of proper location of the
AURATON 2020 controlle
Appropriate operation of the controller strongly
depends on its location. The location without air
circulation or in a directly insolated place results in
inappropriate control of temperature.
In order to ensure proper operation of the controller
place it on an internal wall of the building (between
the rooms).
A place of usual sojourn should be chosen, with
free air circulation.
Avoid the places in the proximity of heat emitting
equipment (TV set, heater, refrigerator) or
subject to direct insolation. Do not locate the
controller in a place adjacent to the door, in
order to avoid its vibration.
150cm
proper location of the controller
AURATON 2020 - Installation 32
EN
1.2 Conductor terminals of AURATON 2020
The conductor terminals may be accessed after
removing the cover of the front controller panel,
batteries, and 2 screws fixing the protection plate.
There are three terminals, marked by COM, NO,
and NC. This is a typical unipole two-state relay.
1.3 Assembly of the AURATON 2020 controller
The controller is assembled with the help of a
pattern. Bore two holes of the diameter of 6mm in
the wall. Drive the bolts and tighten the controller
with screws, the left-hand screw longer than the
right-hand one.
Note: In case of installation of a controller
provided with a floor sensor pay attention to
Figure inserted in Section 18.3, page 24.
Note: In case of a wooden wall the pins should not
be used. Drill the holes of 2.7mm instead of 6mm
diameter and fasten the screws directly to the
wood.
PROG DAY
RETURN
HOUR
MIN
FILTER
OFF HEAT
5°C
AUTO MAN
NC
COM
NO
33 EN AURATON 2020 - Installation
2. Acquaintance with the
AURATON 2020
AURATON 2020 TX Plus
2.1 Outer view
The AURATON 2020 and AURATON 2020 TX Plus
are programmable controllers. They are able to
adjust the room temperature to the desired level 4
times within 24 hours, from Monday to Friday, and
twice within 24 hours on Saturdays and Sundays.
This enables very accurate defining the
temperature cycle within the working week, when
activity of inmates is increased, and in weekends,
during a rest time.
It allows for programming with one-minute
accuracy. At the front panel of the controller a
slidable cover is located. When open, it gives
access to the following pushbuttons:
- the time programming pushbuttons:
DAY, HOUR, MIN;
- the button of operation time of a heating system
FILTER;
- temperature programming pushbuttons:
PROG, RETURN;
- the positioning switch
o
5 C - maintaining the antifreeze temperature;
OFF - heating device breaker;
HEAT - automatic operation (heating).
PROG DAY
RETURN
HOUR
MIN
FILTER
OFF HEAT
5°C
AUTO MAN
TH
PROG
:
0C
AURATON 2020, AURATON 2020 TX Plus - Acquaintance 34
EN
At the left-hand side there are
- two triangular buttons for temperature setting
;
- two pushbuttons:
AUTO (automatic control),
MAN (manual control) alternating the controller
operation mode between automatic or manual;
- a large multi-function display LCD.
The cover may be removed in order to exchange
the batteries. Once it is removed the access to
2 R-6 batteries is opened.
2.2 Display
1. The time is displayed in 24-hours system.
2. English abbreviations of the days of the week
indicate the current day.
3. A bar indicating switching on the heating
device.
4. The digits indicate the currently operating
program.
PROG
12
3 4
MANUAL
FILTER
SETPOINT BATT
MO TU WE TH FR SA SU
1
2
3
4
5
6
7
8
9
10
ECONO
:
0C
.
35 EN AURATON 2020, AURATON 2020 TX Plus - Acquaintance
5. Is the SETPOINT indication displayed, the
temperature indicator ‘7’ shows the
programmed temperature instead of the room
temperature.
6. Low battery indicator reminds the need of
exchanging the batteries for new ones. The
batteries should be then replaced as soon as
possible.
7. Temperature. In normal operation mode the
controller displays temperature of the room
where it is installed.
8. Indicator of operating hours of the heating
device.
9. The indicator of energy-saving operation mode
appears (always together with the manual
control indicator) when the program operation is
temporarily suspended in order to set any
energy-saving temperature level for a
predetermined period of time (from 1 to 7 days,
with one-minute accuracy).
10. The manual control indicator appears when
program operation is cancelled and manually
adjusted temperature is to be maintained
permanently.
AURATON 2020, AURATON 2020 TX Plus - Acquaintance 36
EN
3. Putting the controller into
operation
Once the batteries are installed, the
controller starts operation with its
default parameters. It means that the
following information will be displayed:
Time: 00:00 (midnight)
Day: MO (Monday)
Temperature indicator: current room
temperature
Program: 2 (initiated on Sunday and lasting until
6:00 a.m. on Monday).
Temperature settings:
PROG1: from 6:00 a.m. 21ºC
PROG2: from 8:30 a.m. 21ºC
PROG3: from 4:00 p.m. 21ºC
PROG4: from 11:00 p.m. 17ºC
MO
PROG
:
2
0C
It means that from 6:00 a.m. to 8:29 am the
temperature is adjusted to 21ºC, from 8:30 a.m. to
3:59 pm the temperature is adjusted to 21ºC, from
4:00 p.m. to 10:59 pm the temperature is adjusted
to 21ºC, and from 11:00 p.m. to 5:59 am the
temperature is adjusted to 17ºC.
This may be graphically presented as follows:
These setting may be changed
6 12 18 00 6 12 18
21°C 17°C
37 EN AURATON 2020, AURATON 2020 TX Plus - Putting the controller into operation
4. Setting the controller
AURATON 2020
AURATON 2020 TX Plus
4.1 Adjustment of the day of the week
(No 2 at the display)
1. Move the battery cover to the right.
2. Repeat pressing the DAY pushbutton until
proper day of the week appears at the display,
according to the point 2.2.
4.2 Setting the clock
(No 1 at the display)
1. Move the battery cover to the right.
2. Repeat pressing the HOUR pushbutton until
proper hour appears at the display.
3. Repeat pressing the MIN pushbutton until
proper minute appears at the display.
4. Slide the battery cover back to its place. Now
the controller clock indicates proper date and
time.
Note: Longer pressing the DAY, HOUR, or MIN
pushbutton (exceeding 2 seconds) causes
automatic scrolling of the day, hour, or minute
value, respectively.
4.3. Description of the programming function
AURATON 2020 and AURATON 2020 TX RX Plus
remember 8 temperatures that may be adjusted in
the range from 5ºC to 27ºC with the accuracy of
0.5ºC.
The antifreeze temperature is constant and may be
adjusted by the slider (accessible after uncovering
the batteries).
The controller enables adjusting 4 temperature
values for one 24-hours period that will be in force
equally for 5 working days of the week, from
Monday (MO) to Friday (FR). Additionally, the
controller allows to set separately 2 temperatures
for Saturday (SA) and Sunday (SU).
AURATON 2020, AURATON 2020 TX Plus - Setting the controller 38
EN
For Sunday (SU):
4.4 Programming at the first start after installing
the batteries
1. Move the battery cover to the right
and the slider move to HEAT.
2. Press the PROG button, the
display will be as follows:
The indicator of the Program 1
blinks, which means that it is to be
set.
3. Repeat pressing the buttons HOUR or MIN (no
later than 10 seconds after PROG) with a view
to adjust the time of setting the temperature.
In order to program the controller efficiently you
should decide what temperatures would be required
at home (in the office) from Monday to Friday, and
on Saturday and Sunday, and at what time should
they change. A simple table, proposed here, would
be helpful for this purpose.
For the period from Monday to Friday:
For Saturday (SO):
program 3
program 4
program 1
program 2
Program No Hour Temperature
adjustment
program 1
program 2
program 1
program 2
MO TU WE TH FR
SETPOINT
PROG
1 2
34
:
.
0C
Program No Hour Temperature
adjustment
Program No Hour Temperature
adjustment
39 EN AURATON 2020, AURATON 2020 TX Plus - Setting the controller
4. Press the buttons (no later than 10
seconds after setting the hour and minutes) in
order to adjust the temperature that the
controller should maintain since the previously
set time. The temperature may be adjusted in
the range from 5ºC to 27ºC with the
accuracy of 0.5ºC.
5. Press PROG again (no later than 10
seconds after the previous opera-
tion). The display will be as follows:
The indicator of the Program 2
blinks, which means that it is to be
set.
6. Proceed according to the points 3 and 4, in
order to set the time of switching to
the required temperature.
7. Press PROG (no later than 10
seconds after the previous
operation). The display will be as
follows:
MO TU WE TH FR
PROG
1 2
34
:
0C
.
P
M
MO TU WE TH FR
SETPOINT
PROG
0
.
C
1 2
34
:
8. Proceed according to the points 3
and 4.
9. Press PROG. The display will be as
follows:
The program indicator blinks. The
program 4 is to be set.
10. Proceed according to the points 3 and 4. This
way are set up 4 temperature thresholds and
four time moments of the day in which the
temperature should be changed, from Monday
(MO) to Friday (FR).
11. Further PROG pressing (no later than 10
seconds after the previous operation) switches
the procedure to programming two
temperature ranges for Saturday
(SA) and Sunday (SU), separately.
The display will be as follows:
The indicator of the Program 1
blinks, like in the point 2, but the
day indicator shows Saturday
(SA).
MO TU WE TH FR
SETPOINT
PROG
1 2
34
:
.
0C
SA
SETPOINT
PROG
12
3 4
0C
.
:
AURATON 2020, AURATON 2020 TX Plus - Setting the controller 40
EN
This manual suits for next models
1
Table of contents
Other AURATON Thermostat manuals
AURATON
AURATON 3003 User manual
AURATON
AURATON S03 RTH User manual
AURATON
AURATON Tucana User manual
AURATON
AURATON T-1 RT User manual
AURATON
AURATON Tucana User manual
AURATON
AURATON 2005 TX User manual
AURATON
AURATON Auriga User manual
AURATON
AURATON 2100 TX User manual
AURATON
AURATON 1300 User manual
AURATON
AURATON Libra User manual
Popular Thermostat manuals by other brands
Saswell
Saswell SAS920XWHB-7-S-RF User manual and warranty card
Aircalo
Aircalo TFP1-ET85P2 operating manual
Honeywell
Honeywell CM721 user manual
Carrier
Carrier DEBONAIR 33CS Installation and operating instructions
Lennox
Lennox iHarmony Zone Thermostat Installation and setup guide
Gemtech
Gemtech GT7000 Operation
