Audiovox PRO9845A User manual

Model PRO 9845

Owner's Manual

2 Button Remote Keyless Entry System

With Two Auxiliary Outputs

FEATURES:

2 Two Button, 3 Channel RF Transmitters

Three Channel Code Learning Receiver

Remote Panic In All Modes

Built-In Parking Light Output

LED Status Indicator

Ignition Door Locking/Unlocking

Horn Output

OPTIONS:

Remote Trunk Release

Remote Power Window Control

Remote Garage Door Interface

Remote Engine Starter

Starter Interrupt

Siren

Access Guard / 2 Step Unlock

Illuminated Entry

Page 1

Your PRO 9845 Keyless Entry System has many features and available options some

of which must be selected at time of installation. For your reference, the list on the back

page of this manual shows what features and options have been installed with this

particular system. Consult your installing dealer for options that may have been

installed and are not listed.

REMOTE DOOR LOCKING - ACTIVE

1. Turn the engine off, exit the vehicle, and close all doors.

2. Press and release the left button of your key chain transmitter one time, the doors will

lock, the parking lights will flash once, the vehicle's horn (or optional siren) will chirp

once, and the dash mounted LED will begin to flash slowly confirming the system is

locked.

SILENT LOCKING - ACTIVE

1. Turn the engine off, exit the vehicle, and close all doors.

2. Press and hold the left button of your key chain transmitter for two seconds, the doors

will lock, the parking lights will flash once, and the dash mounted LED will begin to flash

slowly confirming the system is locked. The horn or optional siren will not chirp.

BACKUP PASSIVE OPERATION (AUTOMATIC)

If the passive arming feature has been selected:

Turn the engine off, exit the vehicle, and close all doors.

The dash mounted LED will immediately begin to flash rapidly indicating that the 30 second

passive arming timer has begun.

If any entry point is opened during the 30 second arming cycle, arming will be suspended.

When all entry points are closed, the arming cycle will begin again.

At the end of the 30 seconds, the parking lights will flash once, the vehicle's horn (or optional

siren) will chirp once, and the dash mounted LED will begin to flash slowly confirming the

system is armed. If the horn (or optional siren) did not sound when arming, then the chirps

have been turned off. Please refer to the section titled "Eliminating the Arm/Disarm Chirps"

later in this manual. Passive door locking is a selectable feature. The doors may or may

not lock passively dependent upon the setup during installation.

PROTECTION WHILE THE SYSTEM IS ARMED

If the optional Starter Interrupt relay has been installed, then whenever the system is

armed, the vehicle starter circuit is disabled, even with the ignition key, the vehicle will not

start. Should an attempt be made to start the engine, while the PRO 9845 is armed, the

starter circuit will remain interrupted.

Whenever the system is armed, the dash mounted LED will slowly flash. This serves as a

visual deterrent to a potential thief. This LED is a very low current light emitting diode, and

will not cause the battery to drain even if left unattended for long periods of time.

Page 2

Page 3

UNLOCKING THE SYSTEM

As you approach the vehicle, press and release the left button on the keychain transmitter,

the doors will unlock, the parking lights will flash two times, the vehicle horn (or optional

siren) will chirp twice, and the dash mounted LED will turn off. If you have the optional

entry illumination circuit installed, the interior light will turn on for 30 seconds or until the

ignition key is switched on.

Note: If the passive arming mode was selected at time of installation, the dash mounted

LED will start flashing rapidly indicating that the system is rearming. Opening any door will

suspend the automatic arming.

SILENT UNLOCKING

1. As you approach the vehicle, press and hold the left button of your key chain transmit-

ter for two seconds, or until the system responds.

The doors will unlock, the parking lights will flash twice, and the dash mounted LED will

turn off, confirming that the system is disarmed. The vehicle horn (or optional siren) will

not chirp. If you have the optional entry illumination circuit installed, the interior light will

turn on for 30 seconds or until the ignition key is switched on.

Note: If the passive arming mode was selected at time of installation, the dash mounted

LED will start flashing rapidly indicating that the system is rearming. Opening any door will

suspend the automatic arming.

OPTIONAL ACCESS GUARD ( Two Step Unlock )

If the optional 2-step unlock feature was installed, then only the driver's door will unlock

after the first press of button one. If you want to unlock all doors, you can simply press the

left button of the keychain transmitter once more within 3 seconds of the first press.

NOTE: If you wait longer than 3 seconds before pressing the left button of the keychain

transmitter again, then the command will be treated as an lock command and the

system will lock.

Two Step unlocking is an optional feature that must be wired upon installation.

VALET / PROGRAM / MANUAL OVERRIDE SWITCH

The valet switch allows you to temporarily prevent the PRO 9845 from arming, eliminating

the need to hand your keychain transmitter to parking attendants or garage mechanics.

When the system is in the valet mode, it will not passively arm or activate the starter

interrupt circuit. However, all keyless entry features, as well as the remote panic feature

will remain operational. To enter the valet mode:

1. Start with the valet switch in the "off" position

2. Turn the ignition switch to the "on" position.

3. Flip the valet switch to the "on" position.

The dash mounted LED will turn on solid (not flashing) indicating that the valet mode has

successfully been entered.

To return to the normal mode of operation, move the valet switch to the "off" position at any

time the ignition switch is in the on position.

ELIMINATING THE LOCK/UNLOCK CHIRPS

You can selectively eliminate the normal lock and unlock chirps by holding the transmitter button

slightly longer when locking and unlocking. This will prevent the siren chirps for one lock or

unlock cycle. If you find this inconvenient and wish to eliminate these chirps permanently,

1. Start with the valet switch in the off position.

2. Turn the ignition switch "on" then "off".

3. Within 10 seconds of turning off the ignition, flip the valet switch on, "off", "on", "off", "on", "off".

4. If the chirps were on before you started, the siren will emit 2 short chirps indicating that the

chirps are now off. If the chirps were off before you started, the siren will emit one short

chirp indicating that the chirps are now on.

REMOTE PANIC OPERATION

The left lock/unlock button of your keychain transmitter also serves as a panic button and will

cause the vehicle horn (or optional siren) to sound on demand. To use the panic feature, you

must be within the system's maximum operating range. In an emergency situation, to use the

panic feature, press and hold the left lock/unlock button of your keychain transmitter for 3

seconds. This will cause the lights to flash, the vehicle horn (or optional siren) to sound, and if

the optional interior illumination circuit was installed, the interior lights to flash. The panic mode

will continue for 30 seconds and then reset.

To disengage the panic feature before the 30 seconds are up, press and hold the left button of

your keychain transmitter for 3 seconds or press the right button momentarily. The doors can

be unlocked or locked while in "panic" feature by momentarily pressing the left button.

ADDITIONAL REMOTE FUNCTION CHANNEL 2

The system has an additional output, (Channel 2) , that can be connected to a number of

different optional accessories. Some of the more common uses for this channel are:

Remote Trunk Release

Remote Window Close

To operate the accessory associated with Channel 2, press and hold the right button of

your keychain transmitter for four seconds.

Page 4

Note: In the event that you lose your keychain transmitter or the transmitter fails to operate

the keyless entry system, the valet switch can be used to override the optional Starter Inter-

rupt, and therefore allow the engine to be started. To override system:

1. Open the door with the vehicle's door key.

2. Turn the ignition switch to the on position.

3. Flip the valet/override switch to the on position.

The system will disarm, allowing the engine to be started, and the vehicle to be operated

normally. Always remember to move the valet switch to the off position to allow the passive

arming and optional starter interrupt features to be operable the next time you park the

vehicle.

Page 5

NOTE: You may access the Channel 2 command regardless of whether the system is

"locked" or "unlocked", but not when the ignition switch is in the on position. This is to prevent

the output from accidentally opening the vehicle's trunk when the vehicle is in motion.

ADDITIONAL REMOTE FUNCTION CHANNEL 3

The system has an additional output, (Channel 3) ,that can be connected to a number of

different optional accessories. Some of the more common uses for this channel are:

Remote Engine Start

Remote Window Close

Remote Garage Door Interface

To operate the accessory associated with Channel 3, simultaneously press both buttons

of your keychain transmitter.

NOTE: The channel 3 output will remain active for as long as the transmitter buttons are

held. Certain accessories may take advantage of the extended output capability

of this channel. To discontinue the output, simply release the transmitter buttons.

IGNITION DOOR LOCKING/UNLOCKING

The PRO 9845 system is capable of being programmed for the added safety and security

of ignition controlled door locking and unlocking. These features are separate, so the

PRO 9845 may be programmed for one, or both, or neither.

When the ignition door locking feature is programmed, the PRO 9845 system will cause

all door locks to lock whenever the ignition switch is turned from the off to on position,

(providing that all doors are closed at that time). All doors will lock approximately 3 seconds

after the vehicle's ignition switch is turned on. This is a nice feature for maintaining the

personal safety of the occupants of the vehicle, in an effortless and automatic manner.

When the ignition door unlocking feature is programmed, the PRO 9845 system will cause

all door locks to unlock whenever the ignition switch is turned from the on to off position.

All doors will unlock immediately after the vehicle's ignition switch is turned off. If 2 Step

unlock was installed, only the driver's door will unlock.

As stated these features are programmed separately, so you may chose to use one, both,

or neither. Please consult with your dealer to consider your options.

TWO STEP UNLOCK (ACCESS GUARD)

By pressing the left button of the keychain transmitter as you would normally, (Please see

the section titled "Unlocking The System", earlier in this manual), the system will disarm, and

only the driver's door will unlock. If however, you should then decide instead that you want

all doors to unlock, you can simply press the left button of the keychain transmitter once more,

within 3 seconds, and all doors will unlock.

Page 6

PRO 9845

SYSTEM FUNCTIONS AT A GLANCE

LED INDICATORS:

RAPID FLASHING = PASSIVE ARMING

SLOW FLASHING = ARMED

OFF = DISARMED

ON SOLID = VALET MODE

OPTIONAL VEHICLE HORN OR SIREN CHIRP INDICATION:

1 CHIRP = ARM

2 CHIRPS = DISARMED

CONTINUOUS = PANIC MODE

ALARM PARKING LAMP INDICATIONS:

1 FLASH = ARM

2 FLASHES = DISARM

CONTINUOUS FLASH = PANIC MODE

ÿþýüûúþ

ÿþýýüûúù ø÷ö ü ûú øôóüòñ G ÿþýýüûú G ø÷öüûú

ñòüöü ò ô ÷ü òñ ù  G  G 

ñòüö ü ò ô ò÷üòñ ù  G  G 

ü ôý ù  G  G 

ÿþýýüûú ô ÷üòñ G  G 

ôòùüôúò öö G ôò G üôúò

ô ÷ù ò ÷ ÿ ýúý G óý ù  ÿ ý ú G   ýú÷òù ÿýú G óý ù  ÿ ý ú

   óý  ú ù ÿýú

ÿûü

÷ù ò÷ G ö ö ò  G ö ö ò  G ö ööòý

ÿþòü÷ G ö ö ò  G ö ö ò  G ö ööòý

úóö ú  ôò úúþýú G ö ö ò  G  ö ö ò  G ö ööòý

úóö ú  ü ò   ýú G ö ö ò  G  ö ö ò  G ö ööòý

úóöú þôþñú ô úòüòñ G ö ö ò  G  ö ö ò  G ö ööòý

úóö ú òñüòú ö þôö úô G ö ö ò  G  ö ö ò  G ö ööòý

þüü

úýüüþú ûüü

ÿ  ÿ   

   ú óúöúòýöþüòñ  ú÷òü÷üþò

This manual suits for next models

Table of contents

Other Audiovox Car Alarm manuals

Audiovox

Audiovox Prestige APS-94FR Operating instructions

Audiovox

Audiovox Prestige 128-8615 User manual

Audiovox

Audiovox Prestige 128-8601 User manual

Audiovox

Audiovox Pursuit PRO-9342WOS2 User manual

Audiovox

Audiovox Pursuit Pro 9544FT3 User manual

Audiovox

Audiovox PRO-9649a User manual

Audiovox

Audiovox Prestige Platinum 128-8124 User manual

Audiovox

Audiovox Pursuit PRO-9675FT4 User manual

Audiovox

Audiovox Pursuit PRO 9232a User manual

Audiovox

Audiovox AX-500 User manual

Audiovox

Audiovox APS620 - Prestige Remote Start User manual

Audiovox

Audiovox Prestige Platinum APS-350-A User manual

Audiovox

Audiovox Prestige Platinum 128-8537 User manual

Audiovox

Audiovox Auto Security AA-9300 User manual

Audiovox

Audiovox Professional PS-330i User manual

Audiovox

Audiovox Prestige APS-25HJ User manual

Audiovox

Audiovox APS-20A User manual

Audiovox

Audiovox Prestige APS-15R User manual

Audiovox

Audiovox Pursuit PRO-9900 User manual

Audiovox

Audiovox Prestige AS-9256 User manual

Audiovox

Audiovox Pursuit PRO 9445FT User manual

Audiovox

Audiovox Prestige Platinum APS-510 User manual

Audiovox

Audiovox Prestige Platinum APS-596a User manual

Audiovox

Audiovox Prestige APS-15CH User manual

Popular Car Alarm manuals by other brands

Clifford

Clifford 3606X owner's guide

Ultra Start

Ultra Start 2500M SERIES install guide

Ultra Start

Ultra Start 650 Series owner's manual

Sparkrite

Sparkrite SRA8 Guide

Viper

Viper 4708V owner's manual

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Installation and maintenance manual

Falcon

Falcon Predator XL3 Installer manual

Clifford

Clifford Sabre II owner's manual

CrimeStopper

CrimeStopper CS-8717 Wiring diagram

Ultra Start

Ultra Start 450 SERIES install guide

Scytek electronic

Scytek electronic Vectra X3 product manual

Excalibur

Excalibur AL-1860-EDPB Operation guide

Clifford

Clifford CYBER 2 owner's manual

Gemini

Gemini 7057 user manual

FlashLogic

FlashLogic FLRSBA PRESTIGE Product guide

Magicar

Magicar FAI-440 manual

Clifford

Clifford Nova 3 owner's manual

Viper

Viper 560XV owner's guide