Audiovox ca 6552 User manual
1ca6552/6552sst.2011AudiovoxElectronicsCorporation.Allrightsreserved.
PROFESSIONAL
SERIES
Security and Remote Start Installation Guide
for models:
ca 6552
ca 6552 SST
2 ca6552/6552sst.2011AudiovoxElectronicsCorporation.Allrightsreserved.
Before You Begin ......................................................................................4
Wire Connection Guide ...........................................................................5
4 Pin Main Harness ...................................................................................7
6 Pin Start Harness ...................................................................................8
6 Pin Output Harness .............................................................................10
8 Pin Input Harness................................................................................. 11
4 Pin Alternate Output Harness .............................................................14
4 Pin AUX Output Harness .....................................................................15
3 Pin Door Lock Output Harness ...........................................................16
Additional Ports ......................................................................................20
Antenna / LED / Programming Port .......................................................20
DBIPort....................................................................................................20
Telematic Interface Port..........................................................................20
Set Up & Programming..........................................................................21
Transmitter Programming........................................................................21
Manual Feature Programming.................................................................21
Programming Feature Banks ..................................................................22
Tach Programming ..................................................................................25
Smart Tachless Mode .............................................................................24
Adjusting the Shock Sensor ..................................................................26
Testing the Shock Sensor ......................................................................26
Chirp Delete - User Accessible..............................................................26
Dome Light Delay / Theater Dimming .....................................................26
Table of Contents
3ca6552/6552sst.2011AudiovoxElectronicsCorporation.Allrightsreserved.
Feature Descriptions ............................................................................. 27
Transmitter Button Functions .............................................................34
Security Trigger Zones .........................................................................36
Remote Start Shutdown Diagnostics ................................................36
System Layout.........................................................................................37
4 ca6552/6552sst.2011AudiovoxElectronicsCorporation.Allrightsreserved.
PROFESSIONALINSTALLATION
STRONGLYRECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys in vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Technical Support (800) 421-3209
or go to
http://techservices.codesystems.com
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air
bags or damage vehicle computers.
Use grommets when routing wires through metal
surfaces
BEFORE YOU BEGIN
5ca6552/6552sst.2011AudiovoxElectronicsCorporation.Allrightsreserved.
6 Pin Start Harness
4 Pin Main Harness
6 Pin Output Harness
1WHITE/RED PARKING LIGHT INPUT
2WHITE PARKING LIGHT OUTPUT
3BLACK GROUND
4BROWN SIREN OUTPUT ( + )
4 PIN MAIN
1BROWN/BLACK HORN OUTPUT ( - )
2BLUE/BLACK IGNITION 3 ( - )
3VIOLET/BLACK AUX 1 OUTPUT ( - )
4RED/WHITE TRUNK RELEASE OUTPUT ( - )
5LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - )
6ORANGE GROUND WHEN ARMED OUTPUT ( - )
6 PIN OUTPUT
1PURPLE STARTER OUTPUT - MOTOR SIDE
2RED BATTERY 12V ( + )
3ORANGE ACCESSORY 1 ( + )
4PINK/WHITE IGNITION 2 ( + )
5RED/WHITE BATTERY 12V ( + )
6PINK IGNITION 1 ( + )
6 PIN START
6 ca6552/6552sst.2011AudiovoxElectronicsCorporation.Allrightsreserved.
8 Pin Input Harness
3 Pin Lock Output Harness
4 Pin Alternate Output Harness
1BLUE UNLOCK ( - )
2OPEN
3GREEN LOCK ( - )
3 PIN
LOCK
4 Pin AUX Output Harness
1BLACK/YELLOW PULSE DURING CRANK ( - )
2GREEN/WHITE PULSE AFTER SHUTDOWN ( - )
3LT BLUE FACTORY ARM / PULSE AFTER START ( - )
4LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - )
4 PIN
ALTERNATE
OUTPUT
1PINK/BLACK AUX 5 OUTPUT ( - )
2ORANGE/BLACK AUX 4 OUTPUT ( - )
3GRAY/BLACK AUX 3 OUTPUT ( - )
4WHITE/BLACK AUX 2 OUTPUT ( - )
4 PIN AUX
OUTPUT
7ca6552/6552sst.2011AudiovoxElectronicsCorporation.Allrightsreserved.
3 BLACK GROUND
Connect the BLACK wire to a solid chassis ground point using a ring terminal and
self tapping screw (not supplied). Scrape away paint from the grounding point to
ensure a good connection. The recommended grounding point is a metal surface
in the driver’s side kick panel area.
NOTE: Do not ground the BLACK wire with any other vehicle components.
4 Pin Main Harness
1 WHITE/RED PARKING LIGHT INPUT
2 WHITE PARKINGLIGHTOUTPUT
Locate the parking light output wire at the vehicle’s light switch.
Verification: This wire registers positive voltage when the parking lights are
turned on.
Positive switching Parking Lights:
Connect the WHITE/RED wire to a 15 Amp max fused battery source.
Connect the WHITE wire to the parking light output wire.
Negative switching Parking Lights:
Connect the WHITE/RED wire to a good chassis ground.
Connect the WHITE wire to the parking light output wire.
4 BROWN SIREN OUTPUT ( + )
Locate a suitable mounting location in the engine compartment for the siren, away
from moving parts.
With the bell of the siren aiming downwards, secure the siren in place using self
tapping screws, being careful not do drill into any hoses, wiring or components.
Connect the BLACK siren wire to a chassis ground using a ring terminal and self
tapping screw (not supplied).
Route the BROWN siren output wire from the control module through the firewall
and connect to the RED wire on the siren.
NOTE: Be sure to loom the siren wires, and seal the grommet.
8 ca6552/6552sst.2011AudiovoxElectronicsCorporation.Allrightsreserved.
3 ORANGE ACCESSORY 1 ( + )
Locate the vehicle’s accessory wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to ACC
(Accessory) and the ON (or RUN) position. The voltage drops out when the
key is turned to the START(or CRANK) position.
Connect the ORANGE wire to the vehicle’s accessory wire.
6 Pin Start Harness
1 PURPLE STARTER OUTPUT ( + )
Locate the vehicle starter wire.
Verification: This wire registers voltage only when the key is turned to the
START position. Cut the vehicle's starter wire in half when installing the
starter kill relay.
Verification after starter wire is cut:
KEY SIDE of starter wire registers voltage when the key is turned to the
START position.
MOTOR SIDE of starter wire registers no voltage.
Connect the PURPLE wire to the vehicle starter wire, use the MOTOR SIDE of the vehicle
starter wire when installing the starter kill relay.
2 RED BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
9ca6552/6552sst.2011AudiovoxElectronicsCorporation.Allrightsreserved.
4 PINK/WHITE IGNITION2( +)
Locate the vehicle’s 2nd ignition wire at the ignition switch (if equipped).
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position, but not the ACC (Accessory) position. The voltage does not
drop out when the key is turned to the START(or CRANK) position.
Connect the PINK/WHITE wire to the vehicle’s ignition 2 wire.
Programmable output: IGN, ACC, Start.
6 PINK IGNITION1( +)
Locate the vehicle’s ignition wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position. The voltage does not drop out when the key is turned to the
START(or CRANK) position.
Connect the PINK wire to the vehicle’s Ignition wire.
This wire is also used for Ignition 1 Output.
5 RED/WHITE BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED/WHITE wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
10 ca6552/6552sst.2011AudiovoxElectronicsCorporation.Allrightsreserved.
Fused +12 Volt
Battery Source
30
87
87a
86 85
BLUE/BLACK ActiveOutput
Wire
VATS Control Module
Matching Value
Resistor
Ignition Switch
VATS Wire #1, WHITE or WHITE/BLACK
VATS Wire #2, WHITE or VIOLET/WHITE
X CUT
GM VATS
Fused +12 Volt
Battery Source
30
87
87a
86 85
BLUE/BLACK Active Outpu
t
Wire
To Vehicle's 2nd or
3rd Ignition Wire
Jump To PINK
Ignition Output
Wire From
Control Module
Ignition 3 Accessory 2/3
Fused +12 Volt
Battery Source
30
87
87a
86 85
BLUE/BLACK Active Outpu
t
Wire
To Vehicle's 2nd or 3rd
Accessory Wire
Jump To ORANGE
Accessory Output
Wire From
Control Module
2 BLUE/BLACK IGNITION 3 / ACTIVE OUTPUT ( - )
The Active Output/Ignition 3 output wire provides a ground output when the remote
start function is activated and remains until 4 seconds after the remote start is
shutdown. The Ignition 3 output wire can be used for several functions listed
below. If this wire will be used for multiple application's a 1 amp diode is required
in-line with the stripe facing the control module.
Factory transponder (coded key) bypass.
General Motors VATS bypass, see the following diagram. Use an SPDT relay (not
supplied).
Ignition 3 output, see the following diagram. Use an SPDT relay (not supplied).
Accessory 2/3 output, see the following diagram. Use an SPDT relay (not
supplied).
6 Pin Output Harness
1 BROWN/BLACK HORN OUTPUT ( - )
Locate the vehicle’s horn wire.
Verification: This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current
output, 200mA.
Other manuals for ca 6552
1
This manual suits for next models
1
Table of contents
Other Audiovox Car Alarm manuals
Audiovox
Audiovox AA-9124 User manual
Audiovox
Audiovox Prestige Platinum APS-410a User manual
Audiovox
Audiovox APS-25C User manual
Audiovox
Audiovox Prestige Platinum APS-596a User manual
Audiovox
Audiovox Prestige Platinum 128-5730A User manual
Audiovox
Audiovox ca 6552 User manual
Audiovox
Audiovox Prestige Platinum 128-8533 User manual
Audiovox
Audiovox Pursuit PRO 2000S User manual
Audiovox
Audiovox Car Security System APS-610 User manual
Audiovox
Audiovox Prestige APS-25KB User manual
Audiovox
Audiovox Pursuit PRO-9642 User manual
Audiovox
Audiovox CarLink ASCL1 User manual
Audiovox
Audiovox Pursuit PRO 9644a User manual
Audiovox
Audiovox Prestige Platinum APS-700 Parts list manual
Audiovox
Audiovox Prestige Platinum 128-8537 User manual
Audiovox
Audiovox Prestige Platinum APS-255CH User manual
Audiovox
Audiovox Pursuit PRO-9056 User manual
Audiovox
Audiovox APS-787C User manual
Audiovox
Audiovox PRO 9644 User manual
Audiovox
Audiovox Pursuit PRO 2000S How to use
Popular Car Alarm manuals by other brands
Clifford
Clifford 3606X owner's guide
Ultra Start
Ultra Start 2500M SERIES install guide
Ultra Start
Ultra Start 650 Series owner's manual
Sparkrite
Sparkrite SRA8 Guide
Viper
Viper 4708V owner's manual
Federal Signal Corporation
Federal Signal Corporation Pathfinder Siren Series Installation and maintenance manual
