AUDAC CS85 Installation and operating instructions

Other manuals for CS85

1

This manual suits for next models

4

Table of contents

Popular Speakers manuals by other brands

argon audio

argon audio IE20 quick start

Denon

Denon SC-N7 owner's manual

Gemline

Gemline Ace 3952 user manual

Focal

Focal ON WALL 300 User manua

HEADRUSH

HEADRUSH Maximus HRSP 5024 manual

SoundLogic

SoundLogic BCCS-6/6395 instruction manual

Peavey

Peavey DTH 218 Specification sheet

Avantree

Avantree Pluto Air user guide

Morel

Morel Integra Series INTEGRA OVATION 4 install guide

Oppo

Oppo SONICA quick start guide

Bose

Bose SoundLink Wireless Music System owner's guide

Rocksteady

Rocksteady Stadium owner's manual

Bowers & Wilkins

Bowers & Wilkins 4 owner's manual

Sonance

Sonance SONOS OUTDOOR Series installation manual

Electro-Voice

Electro-Voice EVID FM4.2 Brochure & specs

Pioneer

Pioneer XW-HTD630 manual

Onn

Onn BWA16AA002 Product guide

HP

HP GL313AA - USB Speakers PC Multimedia quick start guide

PROFESSIONAL AUDIO EQUIPMENT

Built-in Ceiling or Wall Spea er CS85

User Manual &

Installation Guide

Ceiling

Speaker

CS85

AUDAC

1

11

1

A U D A C P R O F E S S I O N A L A U D I O E Q U I P M E N T

User Manual & Installation Guide

 AUDAC

http://www.audac.be

info@audac.be

Before connecting or installing this product, first read these instructions carefully

2

22

2

Warning

• Use only the correct amplifier output voltage and impedance, exceeding these limits could

cause fire or other failures.

• Avoid explosions: do not use the spea er around gasoline, thinner or other combustibles.

• Only install the spea er in locations that can structurally support the weight of the spea er.

Not doing this may result in the spea er falling down.

• Do not use any other method than specified to mount the spea er. If extreme force is applied

to the spea er, it could fall down.

• Attach a safety wire to the spea er when the spea er is mounted high above the ground.

Failure in doing so could cause the spea er to fall down for any reason.

• Avoid mounting the spea er in locations exposed to constant vibrations. The mounting points

can be damaged by excessive vibrations, potentially causing the spea er to fall down.

Caution

• Avoid electric shoc s: switch off the amplifier power when connecting the spea er.

• Avoid installing the spea er in locations exposed to solvents, acids, smo e and heaters, as

excessive exposure to these factors could result in spea er failure, fire or electric shoc .

• Do not operate the spea er for an extended period of time at distorted sound. This could

cause (irreparable) damage to the spea er.

• Do not stand or sit on, nor hang down from the spea er, as this may cause failure of the

spea er.

3

33

3

Installation

• Ma e a hole with a diameter of 240mm. This is very easy when you use the carton that is

inside of the box .

• Ta e the grille from the spea er and put the spea er in the hole.

• Tighten the screws of the spea er so that the spea er will be clasped on the ceiling or wall.

• Inside of the box, you can find gums. Put these gums on the sides of the grille. Then put the

grille on the spea er. The gums on the sides of the grille will prevent the grille from falling

down.

Connections

I pedance

• Plug the spea er cable into the soc et at the bac of the spea er. Ma e sure to match the

impedance. Always plug one cable into the common soc et and the other cable into the

soc et of the desired power tapping.

Cable

• Be sure that you use the following polarities for your spea er cable when using several

spea ers in the same location.

Red : Negative or common

Blac : Positive

• The total rated input of all connected spea ers may not exceed the amplifiers output.

4

44

4

Specifications

Nominal Power 40 Watt

SPL (1W/1m) 94 dB

SPL (40W/1m) 101.8 dB

Impedance 8 Ohm

Line transformer impedance 1600 Ohm/6W

3300 Ohm/3W

6600 Ohm/1.5W

Frequency Response 40-20000 Hz

Dimensions (Diameter x Depth) 275x90 mm

Cut-out Diameter 240 mm

Weight 1.4 Kg

Mounting 4 Screws with clamp

Color White RAL9010