Atmel QT600 User manual

Atmel QT600

Quick Start Guide

Touch Solutions

Looking to take your design to the next level?

You have made the right choice in purchasing

the Atmel®QT600 Development Kit. It allows

you to demo Atmel button, slider and wheel

technology and add additional modules/boards.

The kit also to enables you to validate your

own design/board while leveraging the best

touch and microcontroller solutions available.

Introduction

Download the latest software

To get started, visit http://www.atmel.com/qtouchsuite and download four pieces of software:

• Atmel QTouch Studio®(version 4.3 or later) - Visual Studio + .NET (version 3.5 or later)

• Atmel AVR®Studio (version 4.18 or later) AND ALL Service Packs (SPx)

• Atmel QTouch®Library (version 4.3 or later)

• GNU Compiler – Download at http://sourceforge.net/projects/winavr/files

The photo above shows three sets of boards (sensor board and corresponding microcontroller board):

• QTouch8 with the ATtiny88

• QTouch16 with either the ATXMEGA128A1 or the ATmega324

• QMatrix 8x8 with either the ATXMEGA128A1 or the ATmega324

*UC3L MCU board in 2011

Atmel QTouch8

Atmel QMatrix 8x8

Atmel ATXMEGA128A1

Atmel QTouch16

Atmel ATtiny88

Atmel QT600 interface

Atmel ATmega324

Figure 1 – The Atmel QT600 Evaluation Kit includes these microcontroller and sensor boards

Atmel QT600 Quick Start Guide

Connect the kit modules

1QTouch8 with ATtiny88

Choose the QTouch8 and the ATtiny88:

1.1 Open the Atmel AVR Studio®

1.2 Select Open in Project Wizard window

1.3 Select C:\Program Files\Atmel\Atmel_QTouch_Libaries_4.3\Generic_QTouch_Libraries\AVR_Tiny_Mega_

XMega\QTouch\ example_projects\QT600_ATtiny88_gnu_qt8

1.4 Connect the 6-conductor ribbon cable from the ISP header on the ATtiny88 board to the ISP/PDI header on the

QT600 Interface board

1.5 Connect the flex cable from the QTouch8 board to the ATtiny88 board

1.6 Connect the USB cable between your PC and the QT600 Interface board (Three LEDs should light up—then hold

the button down for five seconds until the ‘Touch Data’ LED turns off)

1.7 In AVR Studio, click the ‘Con’ button on the top toolbar

1.8 Select QT600 as the Platform and USB as the Port, and then click connect

VTG Jumper

Figure 2 – Close-up of the Atmel QT600 interface board and location of the VTG

Note: On the main QT600 control board, make sure the jumper is in place on the VTG. The board should be configured as above:

Touch Solutions

Atmel QT600 Quick Start Guide

Affix the rubber stoppers to

QTouch8 (4), QTouch16 (4),

QMatrix 8x8 (6), and the QT600

main controller board (4) leaving

two spares.

1.9 Select Main tab

1.9.1 Device and Signature Bytes = ATtiny88

1.9.2 Programming Mode and Target Settings = ISP Mode

1.9.2.1 Settings ISP Freq = 200.0kHz (click Write)

1.10 Select HW Settings tab

1.10.1 VTarget = Target Voltage: 3.3V (click Write)

1.11 Select Program tab

1.11.1 Flash

1.11.1.1 Input HEX File = C:\Program Files\Atmel\Atmel_QTouch_Libaries_4.3\Generic_QTouch_

Libraries\AVR_Tiny_Mega_XMega\QTouch\example_projects\QT600_ATtiny88_gnu.hex

1.11.1.2 Click Program (STATUS LED on Interface Board turns red during programming then back to

green when programming is complete)

1.12 Disconnect the USB cable from PC

1.13 Remove the 6-conductor ribbon cable

1.14 Connect the 10-conductor ribbon cable between the TOUCH DATA headers on the ATtiny88 and

interface boards

1.15 Reconnect the USB cable to PC

1.16 In Atmel®AVR Studio®, click on the ‘QT’ icon in the toolbar to launch Atmel QTouch Studio®

1.17 In QTouch Studio

1.17.1 Make sure that the Application Mode on the left side is set to Analysis Mode

1.17.2 Just below (under Touch Data Read Control), click Start Reading

1.17.3 QTouch Studio is now reading touch data from your QT600. You will see changes in the Virtual Kit View

as you touch the sensor regions on the QTouch8 board.

Program

and run

the demo

Atmel QT600 Quick Start Guide

Figure 3 – Atmel QTouch8 Sensor

Board Displayed on CPU Monitor

Figure 4 – Complete Set-up for the Atmel QTouch8 sensor board: The sensor board is

connected to the ATtiny88, which in turn is connected to the interface board

Sensor Board /

MCU Board

1.2)

To Program

1.6.1)

Main Lab - Device

and Signature Bytes

1.61)

Main Tab - Programming Mode

and Target Settings

1.7)

HW Setting tab

1.11)

To Program

and Run

1.8)

Program Tab --> Flash Hex Files

c:\Programs Files\Atmel_QTouch_Libaries_4.3\

Generic_QTouch_Libraries\AVR_Tiny_Mega_

XMega\

QTouch8 /

ATtiny88 6-conductor

ribbon cable

into ISP pins

ATtiny88

ISP Mode

(Settings = ISP Frequency =

200kHz)

VTarget = Target

Voltage: 3.3V

(click Write)

10-conductor

ribbon cable

into TOUCH

DATA

QTouch\example_projects\

QT600_ATtiny88_gnu.hex

ATouch16 /

ATXMEGA128A1 10-conductor

ribbon cable

into JTAG pins

ATxmega128A1

JTAG Mode (Settings = ‘Target

device is not part of a JTAG daisy

chain’)

VTarget = Target

Voltage: 3.3V

(click Write)

10-conductor

ribbon cable

into TOUCH

DATA

QTouch\example_projects\

QT600_ATxmega128a1_qt16_gnu.hex

QMatrix 8x8 /

ATmega324 10-conductor

ribbon cable

into JTAG pins

ATmega324PA

JTAG Mode (Settings = ‘Target

device is not part of a JTAG daisy

chain’)

VTarget = Target

Voltage: 3.3V

(click Write)

10-conductor

ribbon cable

into TOUCH

DATA

QMatrix\example_projects\

QT600_ATmega324_qm64_gnu.hex

Touch Solutions

Connect Kit Modules

2QTouch16 with ATmega324 and QMatrix 8x8 with ATXMEGA128A1

2.1 By using the table below and following the same procedures as in step number 1 above, you can program and run

both of these boards

Figure 6 – Complete set-up for the Atmel QTouch16 sensor board: The sensor board is connected to the Atmel ATXMEGA128A1, which in turn

is connected to the interface board

Figure 5 – Atmel®QTouch16 sensor board displayed on CPU monitor

Figure 8 – Complete set-up for the Atmel®QMatrix 8x8 sensor board: The sensor board is connected to the Atmel ATmega324, which in turn is

connected to the interface board

Figure 7 – Atmel QMatrix 8x8 sensor board displayed on CPU monitor

References

Atmel QTouch®Library User Guide - http://www.atmel.com/lib/pdf/Atmel_TLib3-1_CreateProjectV14_IAR+GCC.pdf

Atmel Touch Sensors Design Guide - http://www.atmel.com/dyn/resources/prod_documents/doc10620.pdf

Application Notes - http://www.atmel.com/dyn/products/app_notes.asp?family_id=697

Atmel®QT600 Application Note – Coming soon

Atmel QT600 Quick Start Guide

Touch Solutions

Atmel Corporation

2325 Orchard Parkway

San Jose, CA 95131

USA

Tel: (+1)(408) 441-0311

Fax: (+1)(408) 487-2600

www.atmel.com

Atmel®, logo and combinations thereof, TINYAVR®, AVR®, AVR UC3®, AVR STUDIO®, QTOUCH®, QTOUCH STUDIO®, PICOPOWER®and others are registered trademarks or

trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel

products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY

RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT,

INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR

INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and

reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not

suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

Atmel Asia Limited

Unit 01-5 & 16, 19F

BEA Tower, Millennium City 5

418 Kwun Tong Road

Kwun Tong, Kowloon

HONG KONG

Tel: (+852) 2245-6100

Fax: (+852) 2722-1369

Atmel Munich GmbH

Business Campus

Parkring 4

D-85748 Garching b. Munich

GERMANY

Tel: (+49) 89-31970-0

Fax: (+49) 89-3194621

Atmel Japan

9F, Tonetsu Shinkawa Bldg.

1-24-8 Shinkawa

Chuo-ku, Tokyo 104-0033

JAPAN

Tel: (+81)(3) 3523-3551

Fax: (+81)(3) 3523-7581

Мы молодая и активно развивающаяся компания в области поставок

электронных компонентов. Мы поставляем электронные компоненты

отечественного и импортного производства напрямую от производителей и с

крупнейших складов мира.

Благодаря сотрудничеству с мировыми поставщиками мы осуществляем

комплексные и плановые поставки широчайшего спектра электронных

компонентов.

Собственная эффективная логистика и склад в обеспечивает надежную

поставку продукции в точно указанные сроки по всей России.

Мы осуществляем техническую поддержку нашим клиентам и

предпродажную проверку качества продукции. На все поставляемые продукты

мы предоставляем гарантию .

Осуществляем поставки продукции под контролем ВП МО РФ на

предприятия военно-промышленного комплекса России , а также работаем в

рамках 275 ФЗ с открытием отдельных счетов в уполномоченном банке. Система

менеджмента качества компании соответствует требованиям ГОСТ ISO 9001.

Минимальные сроки поставки, гибкие цены, неограниченный

ассортимент и индивидуальный подход к клиентам являются основой для

выстраивания долгосрочного и эффективного сотрудничества с предприятиями

радиоэлектронной промышленности, предприятиями ВПК и научно-

исследовательскими институтами России.

С нами вы становитесь еще успешнее!

Наши контакты:

Телефон:

+7 812 627 14 35

Электронная почта:

sales@st-electron.ru

Адрес:

198099, Санкт-Петербург,

Промышленная ул, дом № 19, литера Н,

помещение 100-Н Офис 331

Table of contents

Other Atmel Microcontroller manuals

Atmel

Atmel AVR1612 Installation and operating instructions

Atmel

Atmel SAM G55 Xplained Pro User manual

Atmel

Atmel AVR XMEGA-A3BU Installation and operating instructions

Atmel

Atmel AT32UC3L064 User manual

Atmel

Atmel ATmega128A-STK600 Installation and operating instructions

Atmel

Atmel AT88RF1354 User manual

Atmel

Atmel SMARTCARD XPRO User manual

Atmel

Atmel AVR1605 User manual

Atmel

Atmel ATmega48PV User manual

Atmel

Atmel 80C51 Installation and operating instructions

Atmel

Atmel SAM4L Xplained Pro User manual

Atmel

Atmel ATmega324PB User manual

Atmel

Atmel STK520 User manual

Atmel

Atmel ATmega328PB Xplained Mini Installation and operating instructions

Atmel

Atmel AT88CK109STK3 Installation manual

Atmel

Atmel AT88CK101BK8 Installation manual

Atmel

Atmel AVR ATtiny10 Series User manual

Atmel

Atmel AVR AVR350 Installation and operating instructions

Atmel

Atmel AVR AT90CAN32 User manual

Atmel

Atmel SAM L21 Xplained Pro User manual

Atmel

Atmel AT89C51 User guide

Atmel

Atmel ARIS+ AT88SC-ADK2 User manual

Atmel

Atmel AT91 Series User manual

Atmel

Atmel AT91FR40162S User manual

Popular Microcontroller manuals by other brands

AMS

AMS AS7261 Demo Kit user guide

Novatek

Novatek NT6861 manual

Espressif Systems

Espressif Systems ESP8266 SDK AT Instruction Set

Nuvoton

Nuvoton ISD61S00 ChipCorder Design guide

STMicrolectronics

STMicrolectronics ST7 Assembler Linker user manual

Texas Instruments

Texas Instruments Chipcon CC2420DK user manual

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM user guide

NEC

NEC 78GK0S/K 1+ Series Application note

Mikroe

Mikroe SEMITECH N-PLC Click Application note

Intel

Intel Agilex user guide

Cypress

Cypress CY4607 HX2VL quick start guide

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE manual

Texas Instruments

Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual

CYPRES

CYPRES CY14NVSRAMKIT-001 user guide

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM user guide

Espressif Systems

Espressif Systems ESP8266EX Programming guide

Abov

Abov AC33M8128L user manual

Laird

Laird BL654PA user guide