Assa Abloy Premium Plus HSA6410 User manual

Premium+ Alarm Kit

HSA6410

Installation · Programming · Operating

Keep this manual safe for reference and future maintenance

Introduction Contents

General System Overview

Thank you for choosing the Yale Wireless Alarm System.

This simple to install system has been designed with the

user in mind.

No connections

All the components are self contained and no connections

are needed between the panels. There is no need to

damage the home decor, lift carpets or run cables.

Number of devices

You can install up to 20 devices in the system. As well as

extra door/window contacts, PIR motion detectors and

smoke detectors, you can add keyfob remote controls and

keypads for added control convenience.

Long battery life

There is no need to wire into the mains supply or seek

the services of a qualiﬁed electrician. The control panel is

Batteries operate for 2 years or more before they need

changing*. Regular testing and battery changes (when

notiﬁed by the system) will ensure reliability and peace of

mind. Please note that alkaline batteries must be used as

replacements. *Depending on usage.

Tamper proof system

The security accessories, control panel and external siren

are ‘tamper’ protected. Any unauthorised tampering with

these items will result in an alarm. This feature can be

turned off by the user when a battery change is required.

Take care of your safety

Display extreme caution when using ladders or steps,

please follow manufacturer’s instructions.

Be careful when using hand and power tools and follow

the manufacturer’s guidelines when using them. Take care

that the correct tools are used. Wear goggles or protective

clothing where required.

The external Siren is extremely loud, please ensure you

replace the cover and retreat to a safe distance before

testing.

Caution

The dialling facilities must only be used with persons who

have consented to being contacted by the system.

The system is not to be used to make 999 emergency

calls directly. Yale do not hold responsibility for any actions

taken by emergency services for incorrect use of the

dialling facility.

Information and illustrations are subject to change within this

document. Yale reserves the right to alter the speciﬁcation and

product design at anytime without notice. Yale® is a registered

Contents

1Location planning 2

2Unpack all the parts 4

3First Time Easy Install 6

4Mounting alarm devices 9

5Control Panel Menu System in Detail 12

6Using the System 18

Adding and using Accessories 20

Changing the batteries 22

Troubleshooting 24

Speciﬁcations 26

Recommended Installation Sequence

We recommend you follow the simple install

sequence, headings numbered 1-6.

Yale

12abc

4ghi 5jkl 6mno

pqrs

78tuv wxyz

3def

Yale

12abc

4ghi 5jkl 6mno

pqrs

78tuv wxyz

3def

Yale

Location planning

Home and Away Mode Planning

The home arming mode allows the premises to be

part armed so that no one can get inside without

warning the occupier, yet the person already inside

the house can move freely without triggering the

alarm. For example the downstairs of a house can

be armed while upstairs can be disarmed allowing

the user to go to bed without causing an alarm.

If this feature is to be used, then it should be

planned now, before installation.

Decide what areas can be occupied when in home

arming mode, the sensors for these areas should

be programmed to home omit; and the sensors

activated on the path to access the control panel

should be to be set to either Entry or Away Entry as

explained on page 15.

Operating Range

All devices must be within 30 metres of the control

panel and must not be mounted on or near large

metal objects. Avoid obvious sources of electrical

interference such as fridges and microwave ovens.

Tamper Switches

When mounting devices ensure that any tamper

switches close fully. On uneven surfaces it may be

necessary to place packing behind the switch for

reliable operation.

Extend The System

Extend the system in the future to increase your

security or as your needs change.

For example, add extra PIR motion detectors and

extra door/window contacts.

1Work out the best places to locate the devices for maximum protection. Having chosen the

locations do not mount at this stage.

Keypad remote control accessory

When used as second keypad, it is ideal in

bedrooms or at the top of a stairwell so the

ground ﬂoor can be armed when going to bed for

the night. Or, at a side or back door for alternative

entry.

• Mount at chest height for ease of use

• Designed for indoor use only

• Keypad should be accessible from a protected

entry/exit point

• Ensure that the keypad is not visible from the

outside of the premises.

PIR motion detector

• Mount in a position such that an intruder would

normally move across the PIRs ﬁeld of view.

• Height should be between 1.7 and 2.3 metres

above ﬂoor level.

• Location in a corner will ensure wider room

coverage.

• Do not mount the PIR where its ﬁeld of view will

be obstructed e.g. by curtains, ornaments etc.

• Do not point directly at sources of heat e.g. ﬁres

or boilers, and do not position directly above

radiators.

• Avoid mounting the PIR directly facing a

window.

• Do not point the PIR at a door protected by a

door/window contact.

Panic button accessory

The panic button provides extra protection for

you and your family. When help is needed the

button can activate your alarm immediately - even

when the system is disarmed.

• Mount on bedroom wall or by the front door

• Not clearly visible to an intruder

• Easily accessible

• Out of reach of children

Yale

12abc

4ghi 5jkl 6mno

pqrs

78tuv wxyz

3def

Yale

12abc

4ghi 5jkl 6mno

pqrs

78tuv wxyz

3def

Yale

Keyfob remote control accessory

Can be used inside or outside the property and

can be kept on your keyring.

Smoke detector

• Mount in the middle of the ceiling at the top of

a stairwell, or on the centre of hallway ceilings

where smoke would most likely be detected.

• Do not mount in corners or above cooking

appliances and heaters.

• Install additional detectors if there are closed

doors preventing smoke from reaching

detectors. Door/Window contact

Select a door that will be the main point of entry

and exit, usually your front door.

• Mount as high as possible

• Do not aim a PIR motion detector at this door

or window

Yale

12abc

4ghi 5jkl 6mno

pqrs

78tuv wxyz

3def

Yale

12abc

4ghi 5jkl 6mno

pqrs

78tuv wxyz

3def

Yale

PIR motion detector

• Mount in a position such that an intruder would

normally move across the PIRs ﬁeld of view.

• Height should be between 1.7 and 2.3 metres

above ﬂoor level.

• Location in a corner will ensure wider room

coverage.

• Do not mount the PIR where its ﬁeld of view will

be obstructed e.g. by curtains, ornaments etc.

• Do not point directly at sources of heat e.g. ﬁres

or boilers, and do not position directly above

radiators.

• Avoid mounting the PIR directly facing a

window.

• Do not point the PIR at a door protected by a

door/window contact.

Control panel

• Ensure the control panel is accessible when

entering through a protected entry/exit point.

• Avoid mounting the control panel where it would

be visible from the outside of the premises

• Locate by a mains socket and telephone point.

Siren

Choose a position on an external wall where the

siren would be most prominent. Mount as high as

possible, out of easy reach.

Unpack all the parts

2The easiest way to get to know the system and get it up and running quickly is to get all the

devices and accessories programmed on a table top before locating and mounting them.

WARNING

The siren is very loud, be prepared! Take care not to

activate the siren tamper switch unnecessarily.

1Remove the cover by unscrewing the single screw

located on the lid.

2Familiarise yourself with the internal components,

do not switch siren on at this stage, this will be

done at First Time Easy Install, section 3.

PIR movement detectors

1Pull out the plastic pull tab on the back of the PIR.

This will activate the batteries.

2A red light can be seen ﬂashing through the

lens. This will last for 30 seconds indicating the

component’s initiation.

Text Display

Down

Contactless

Reader

Programming

Arm Button

Part-Arm

Button

Disarm

Button

Microphone

Power LED

Add Device

Numeric &

Text Keypad

Back Space

Fault LED

Control panel

A power adaptor is supplied that plugs into mains

supply wall socket and control panel. Do not plug

in at this stage, this will be done at First Time Easy

Install, section 3.

• In addition to the adapter, there is a rechargeable

battery inside the control panel that serves as a

backup in case of a power failure. A fully charged

battery can provide backup power for a period of

at least 10 hours. It takes approximately 36 hours

to fully charge the battery. The control panel is

equipped with a backlit LCD display and keypad

for easy operation in dark. To conserve backup

battery duration the backlights will be switched

off during mains power failure. The control panel

is also provided with a contactless tag reader that

allows the user to tap a tag to disarm the system.

Siren

The siren comes in two shapes, square shaped

and round depending on the kit purchased. The

operation and programming of the sirens are

identical, only the case is different.

Battery

Switch

Siren

Power Socket

Telephone

Socket

Door/window contacts

1Pull out the battery saver tab to activate the battery.

Cover screw

Learn/Test

Button

Status

LED

Battery

saver tab

Gap no more

than 8mm

Magnet

Sensor

Learn/Test

button

LED

Keyfob remote control accessory

1Open the battery compartment using a coin by

turning cover in the direction of the big arrow so

the cover small arrow is next to round dot.

2Insert battery and replace cover.

Smoke detector accessory

1Remove the cover and insert the four AAA

batteries as shown

2The Smoke detector will now enter into self-

calibration mode for 10 minutes. It will resume

normal operation after this period.

Panic button accessory

Remove the cover by loosening the ﬁxing screw

and insert the 12V battery (supplied) as shown.

Please ensure you observe battery polarity.

Door/window contacts

1 Remove the cover of each door/window contact

by loosening the fixing screw.

2Insert two AAA batteries into each detector as

shown. The indicator LED will flash briefly.

Keypad remote control

Remove the cover and insert the 3 AAA alkaline

batteries as shown. The ‘Tx’ LED will flash briefly

while components initialise.

Please note, the Home button on the operating

panel and the jumper switch inside (do not move)

have no function on this model.

Smoke detector accessory

Remove the cover and insert the four AAA

batteries as shown.

Keyfob remote control accessory

Slide off the battery cover, insert the

23A/MN21 battery as shown, and replace

battery cover. Switch to ‘on’.

Help button accessory

Remove the cover by loosening the fixing

screw and insert the 12V battery (supplied) as

shown. Please ensure you observe battery

polarity.

Tamper

switch

Jumper

switch

Tamper

switch

Jumper

switch

Magnet

Extension terminals

Learn/Test button

Learn/Test

button

On/Off sw itch

Door/window contacts

1 Remove the cover of each door/window contact

by loosening the fixing screw.

2Insert two AAA batteries into each detector as

shown. The indicator LED will flash briefly.

Keypad remote control

Remove the cover and insert the 3 AAA alkaline

batteries as shown. The ‘Tx’ LED will flash briefly

while components initialise.

Please note, the Home button on the operating

panel and the jumper switch inside (do not move)

have no function on this model.

Smoke detector accessory

Remove the cover and insert the four AAA

batteries as shown.

Keyfob remote control accessory

Slide off the battery cover, insert the

23A/MN21 battery as shown, and replace

battery cover. Switch to ‘on’.

Help button accessory

Remove the cover by loosening the fixing

screw and insert the 12V battery (supplied) as

shown. Please ensure you observe battery

polarity.

Tamper

switch

Jumper

switch

Tamper

switch

Jumper

switch

Magnet

Extension terminals

Learn/Test button

Learn/Test

button

On/Off sw itch

Keypad remote control

1Pull out the plastic battery saver tab at the back of

the remote keypad. This will activate the batteries.

Battery

saver tab

ale

123

789

Disarm

Home

Arm

LED

Yale

First Time Easy Install

• Any omissions or mistakes can be rectiﬁed

later. Once the ﬁrst time install has been

successfully completed it will not be shown

again.

• More advanced programming can be done

at a later stage including adding and naming

sensors and changing various settings.

Unpack the kit

content on a

table. Remove the

mounting plate

(if ﬁtted) from the

control panel. Move

rightwards to lock

and move leftwards

to release the panel

(panel top facing the

user). Connect the

power adaptor.

The control panel will beep and “Set user code (OK?)”

will be shown, and the green LED will be on.

Move rightwards to lock and move leftwards to release

the panel (panel top facing the user). Using a pointed

tool, slide the battery switch to the right in the direction of

the arrow to switch the internal battery.

The panel is now ready for the ﬁrst time

installation steps:

3The quick install guide will prompt you to program the basic system in easy steps.

1. Set user code (OK?)

Press 3

2. Enter 1st code ….

Enter a four digit PIN code. Press 3

Xcan be use to correct wrong number.

Make a note of the entered code, it will be

required later.

3. Set 2nd code Y/N

Select No to skip, Yes to enter 2nd code.

Maximum 3 set of codes can be set.

The current selection is shown by the

flashing dot on the far LEFT. Use p/qkeys

to navigate.

4. Reset code / Next step

Select reset code to repeat step 2, or next

step to proceed.

Cursor is on NEXT STEP as default

5. Add Device (OK?)

Press 3

6. Push button on Device to Add

Keypad (Keys should be pressed positively within 3 secs of the

previous press)

1Press Panic button A and enter 0000

(The LED will now be ﬂashing. System is now in setting mode)

2 Press Panic button A and enter 7

(The keypad will conﬁrm with two fast ﬂashes that it is in “Siren as master”

mode.)

3 Press Panic button A then 1to send learn-in signal, then

press disarm twice to quit.

ale

123

789

Battery

cover

Coin

slot

Locked

Unlocked

Yale

PRESS

7. Detect (OK?)… Zone01 B

Press 3to confirm

Devices are labeled by the following codes:

·Door Contact DC

· PIR Sensor IR

· Smoke Sensor SD

· Remote Controller RC

· Remote Keypad KP

· Help Button FP (Fix-Panic)

8. More device / Next step

If you have more device to add to the system,

select More devices (this will go back to step

6), or select Next step to move forward.

10. Push learn button on siren (OK?)

• Press 3

• Press learn button on siren

11. Hear beep Y/N

Did you hear the siren beep when you press

the learn button on the siren? If not select No

and step 10 will be repeated.

12. Learn Siren Y/N

Select Yes to learn in siren. Select No to skip

learning siren

After selecting Yes, the siren should beep

13. Hear beep Y/N

Did the siren beep in the last step? If not

select No and go back to step 12

14. Add siren / Next step

You can add more siren or you can select to

move to the next step by using the p/qkey.

15. Set Tel. Number for alert (OK?)

Key in the full telephone number (number you

want to alert in the event of an alarm)

16. Set 2nd num? Y/N

Select yes if you want the system to call more

than one telephone number. Maximum 3

numbers can be stored.

17. Reset Number / Next step

Select reset Number to go back to step 15.

Select next step to move forward.

18. Rec Name&address 10 sec (OK?)

Press 3and follow on screen instruction to

record your message. Please say your name

and address slowly.

19. Record again / Next step

Select record again to go back to step 18.

Select next step to progress.

20. Test call?

You can choose to test the telephone message calling

feature with the Yes/No option. To make a test call plug in

the telephone line cord supplied into the control panel as

shown. Find a convenient telephone line wall socket and

plug the other end of the cord in. Follow the on-screen

instructions to complete the test.

• Check with the called party before doing the test.

• Four messages will be played:

·Address message you have just recorded

·Burglar message

·Emergency message

·Acknowledgement message

• The call can be terminated by the recipient pressing “9”

on the phone or by pressing the 5key on the panel.

• If the call is being made to a mobile or DECT radio phone,

press “9” repeatedly to cancel the call.

21. Call again / Next step

Select Call again to repeat test call.

22. Set Date/Time (OK?)

Press 3. Follow the on-screen instructions to

set both the time and date.

• The date and time is set by using the p/q

keys and then pressing 3when ﬁnished.

9. Add Siren (OK?)

• Remove the siren cover. Ensure

the siren power is switched off and set

the program switch number 1 to ON to

clear memory as shown.

• Press the siren learn button a few times

to drain any residual power.

• Switch on the siren power and wait for the siren

LEDs to flash and siren beep

• Then set the program switch number

1 to OFF, ready for learning in.

• Press 3NORMAL

155.30 33.18

155.31

23. Date/Time? / Next step

Select date/time? To go back to step 22.

Select next step to progress.

24. Start walk test (OK?)

Follow the on-screen instructions to test all the

learnt-in devices except the siren.

• Press the test buttons on the PIR and door contact

and the arm keys on the keyfob and keypad to

send a test signal.

• The walk test can be quit at any time by pressing

the Xkey.

• Walk test is used to check that the sensors are

working correctly. Walk test can also be used

to ﬁnd out if the devices are in radio range of the

control panel.

• The control panel will chime and display the device

that sent the test signal.

25. Test device ? / Next step

To re-test press the pkey and 3, otherwise

press 3directly to go to the next step.

26. Setup ﬁnished (OK?)

Press 3and “Start again?” will be shown, to

restart press the pkey and 3, otherwise

press 3directly to go to ﬁnish.

• The control panel will display “Alarm off” with the

time and date.

• More advanced programming, such as adding

contactless tags, device naming, entry/exit times,

adding other users and any corrections can be

made in the main programming menu, see section

5 Control Panel Menu System in Detail.

• All the devices are set-up as burgular mode. This

will result in the siren ringing instantly when you

enter the house (no countdown). You need to setup

an entry device if you want a countdown period.

See Edit device on page 13.

Steps continued...

Mounting alarm devices

4WARNING To prevent the alarm from activating during installation, the siren must have its

tamper disabled and the control panel must be in ‘Walk Test’/Programme mode.

Control Panel Mounting

Table top

Remove the mounting back plate (if ﬁtted) and

simply place on top of a table on its rubber feet.

•If the mounting plate has been ﬁtted with the

power on, the control panel will show a panel

tamper condition when the plate is removed. To

cancel make sure that the mounting plate is not

ﬁtted and power down by removing the power

plug and switching off the battery. Reconnect

power and switch the battery back on. The panel

tamper will be reset and not activate again unless

the plate is put back on.

Wall Mounting

Using the two holes on the mounting back plate,

mark the position of the holes. Drill two holes and

ﬁx with the screws and plugs provided. Hook the

control panel onto the plate. Ensure that the control

panel is ﬁtted at approximately chest height where

the display can be easily seen and the keypad

convenient to operate.

•The control panel tamper protection will

automatically arm when mounted on the back

plate.

Disabling the system tamper

1Press the key and enter a user PIN code

followed by 3.

2The control panel is now in programming mode,

Select Devices +/-, then Program Siren and

Siren Tamp. Off using the pq3 keys.

3Press 3 when in the Siren Tamp. Off menu

and the control panel will beep followed by an

acknowledgement pip from the siren.

• Siren programming is described more fully

in “Control Panel Menu System in Detail” in

section 5.

• The siren tamper will now be disabled for 1

hour after which it will automatically arm again.

If longer is needed to ﬁt the siren then simply

repeat the steps above.

• Leave the control panel in programming

mode to stop the system responding to

tampers. If the control panel automatically

times out, re-enter programming mode

again.

Mounting the siren

Ensure the tamper switch is fully depressed when

the siren is mounted. If there is a gap, pack with a

suitable spacing material.

Round

Siren

Base

Wall

Spring Guide

Spring compressed

firmly against wall

Square Siren Base

Plunger must

be pressed in

fully against

wall

Wall

1 Find a location where the siren is to be mounted.

2 Using the large screws and wall plugs provided,

screw the siren onto the wall through the 4

mounting holes on the siren base.

3 Fix the siren cover with the securing screw.

4 Using the Programming Devices +/- menu enable

the siren tamper (see the end of this section “Final

step:”) and Arm and Disarm the system with the

control panel.

5 If there are 5 short beeps when armed, the tamper

switch is NOT fully depressed and will need to be

adjusted.

Unset the system and disable the siren tamper as

described above before adjusting the siren tamper

switch. If there is a gap between the wall and the

tamper switch mechanism, pack with a suitable

spacing material.

When adjusted repeat the steps above from steps

3 through 5.

6 If there is one short beep and ﬂash when armed,

the siren is mounted correctly and the siren

installation is complete.

Before mounting it is important to disable the

siren and system tamper to avoid the siren

sounding an alarm.

Mounting other devices

Find a location where the device is to be mounted,

see section “Location Planning” for suggestions.

Mounting the Keypad:

Fixing Slots X 2

Keypad

Cradle Open

1 Drill holes into the wall using the ﬁxing slots as a

template.

2 Fit wall plugs into the wall and ﬁx cradle with the

screws provided.

3 Slide the keypad into the cradle

4 Close the cradle cover so the logo is facing you

Mounting the PIR motion detector

1 Open the PIR by loosening the bottom screw.

Knock out the relevant holes on the base where

the plastic is thinner. The center two knockout

holes are for ﬂat wall mounting while the 4 side

holes are for corner mounting.

Corner fixing

knockouts X 4

Wall fixing

knockouts X 2

2 Drill holes into the wall using the knockout holes on

the base as a template.

3 Fit wall plugs and secure the PIR base with the

screws provided.

4 Fit the PIR back together and tighten bottom

screw, the PIR installation is complete.

Before proceeding to mount the devices

physically, check that the control panel will

receive the system radio transmissions by

doing a simple radio range test.

• Put the control panel into walk test mode.

•KEYPAD: press the arm button.

• HELP BUTTON: press the button.

• ALL OTHER DEVICES: Hold the device

in the desired location and press the

learn/test button, the control panel should

respond with a chime.

• When you are satisﬁed that the devices

work in your chosen locations, proceed

with the installation as described.

• If the control panel does not respond,

the location may be out of range, try

alternative locations until reliable radio

contact is obtained.

The PIRs have a built-in sleep timer to save

battery power. If there is no movement in front

of the PIRs for 1 minute, the PIRs will become

‘ready to signal’ and movement will now be

reported. The PIRs will sleep for 1 minute after

reporting.

Any movement detected in sleep time will not be

reported and will extend the sleep period by a

further 1 minute.

Table of contents

Other Assa Abloy Security System manuals

Assa Abloy

Assa Abloy Yale Secure Connect MZ-1 User manual

Assa Abloy

Assa Abloy Yale EF-KIT2 User manual

Assa Abloy

Assa Abloy effeff EXITalarm Service manual

Assa Abloy

Assa Abloy Yale HSA6610 User manual

Assa Abloy

Assa Abloy Yale SV-8C-4ABFX User manual

Assa Abloy

Assa Abloy Securitron M680E User manual

Assa Abloy

Assa Abloy Yale AC-PS User manual

Assa Abloy

Assa Abloy Yale Easy Fit EF Series User manual

Assa Abloy

Assa Abloy Yale Smart Living SR-1100 User manual

Assa Abloy

Assa Abloy SR-A100-00DC User manual

Assa Abloy

Assa Abloy Yale SAA5015 User manual

Assa Abloy

Assa Abloy Yale Sync Smart Home Alarm User manual

Assa Abloy

Assa Abloy Pando S559685084 User manual

Assa Abloy

Assa Abloy Yale SR-PIR User manual

Assa Abloy

Assa Abloy Yale AC-PB User manual

Assa Abloy

Assa Abloy MSL mFlipLock drive User manual

Assa Abloy

Assa Abloy Yale SAA5015 User manual

Assa Abloy

Assa Abloy MSL mFlipLock drive User manual

Assa Abloy

Assa Abloy HSA6500 User manual

Assa Abloy

Assa Abloy MSL mFlipLock check User manual

Assa Abloy

Assa Abloy Yale Smart Home Alarm User manual

Assa Abloy

Assa Abloy 1370 User manual

Assa Abloy

Assa Abloy Yale SV-4C-2ABFX-2 User manual

Assa Abloy

Assa Abloy Yale AC-KF User manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual