Assa Abloy Securitron EEB3N User manual

PN# 500-12600

Page 1 Rev. F, 01/15

SECURITRON EEB2, EEB3N EXIT BUTTON WITH INTEGRATED TIMER

INSTALLATION AND OPERATING INSTRUCTIONS

DESCRIPTION

Model EEB2 is a two-inch square, exit button, mounted on a stainless steel (S.S.), single gang key plate. Model EEB3N

is a rectangular exit button, mounted on a 1 3/4” S.S. narrow stile key plate. Both EEB2 and EEB3N have a 3A switching

capacity and a timer set for 30 seconds. These units are intended only for release of a magnetic lock from the inside of a

door. When the button is pressed, the lock releases for 30 seconds. If pressed again during the 30-second lock release

period, the unit will “retrigger” starting a new 30-second lock release period. These buttons are specifically intended for

installation on access controlled egress doors, as described in the Building Officials and Code Administrators (BOCA)

code. A motion detector, such as the Securitron Model XMS, is the primary means of magnetic lock release on the door.

The EEB2 or EEB3N exit button is employed as a backup means of releasing the lock in case of a problem with the

motion detector. It should be noted that the exact release time will vary with temperature, but it will not be less than 30

seconds.

UL294 ACCESS CONTROL PERFORMANCE LEVELS

The following are the UL294 access control performance levels:

• Destructive Attack = Level 1

• Line Security = Level 1

• Endurance = Level 1 (6,000 cycles)

• Standby Power = Level 1

MOUNTING THE EEB2 AND EEB3N EXIT BUTTONS

1. MOUNT the EEB2 using its included mounting device.

NOTE: The aluminum door frame must be sufficiently routed out to accommodate the EEB3N components.

2. MOUNT the EEB3N directly on a narrow stile aluminum door frame.

WIRING THE EEB2 AND EEB3N

CAUTION

THE EEB2 and EEB3N can be damaged if operated on 24 VDC with the jumper in place, or operated on a power

supply different than what is operating the magnetic lock.

NOTE 1: The EEB2 and EEB3N operate on 12 VDC or 24 VDC, and can accept the use of full-wave rectified DC

(transformer and bridge rectifier).

NOTE 2: EEB2 and EEB3N are factory shipped with the jumper in place (12 VDC). If jumper is removed, unit operates

on 24 VDC.

NOTE 3: EEB2 and EEB3N draw no current when at rest, and only draw 28 mA at 12 VDC or 38 mA at 24VDC when

releasing the lock.

1. WIRE the EEB2 or EEB3N in accordance with Figure 1, “Wire Identification and Typical Connection,” and Figure 2,

“Internal Schematic.”

Figure 1. Wire Identification and Typical Connection

Securitron

10027 S. 51st St., Ste. 102, Phoenix, AZ 85044

Tel: 1.800.624.5625

Mon-Fri: 6:00am - 4:00pm PDT

techsupport@securitron.com www.securitron.com

Page 2 Rev. F, 01/15

Figure 2. Internal Schematic

CHANGING THE ALTERNATE LENS ON THE EEB2

1. GRASP and TURN OVER the keyplate.

2. From the back, ROTATE the white contact block of the switch counterclockwise to the 11:00 o’clock position, and PULL

straight back to remove.

3. SLIDE a slender smooth-ended object, such as a marker pen, inside the switch body up against the lens.

4. PLACE the object on a smooth surface with the keyplate on top, and TAP the keyplate up and down on the object to

pop off the lens.

5. REMOVE the lens and insert.

6. TURN OVER the keyplate and PLACE a new insert onto the front of switch.

7. ENSURE that the the text on the insert is correctly reading to the keyplate, and PLACE the matching colour lens on top

of insert.

8. PRESS around all edges of the lens until it snaps in place.

9. DEPRESS lens several times to ensure smooth operation and the lens is not binding.

10. With the terminals upward, INSERT the contact block back into the back of the switch at the 11:00 o’clock position and

ROTATE clockwise until it stops straight up and down.

CHANGING THE ALTERNATE LENS ON THE EEB3N

1. While holding keyplate, GRASP the top and bottom of the lens and PULL straight out from the keyplate.

2. PLACE a new lens over the switch face, and ENSURE the text on the lens is correctly reading to the keyplate.

3. PRESS completely until it snaps into place.

4. DEPRESS the lens several time to ensure smooth operation and the lens is not binding.

MAGNACARE

WARRANTY

LIFETIME - NO FAULT – TOMORROW

• Lifetime - We guarantee our products, and since we've been making Magnalocks for over 35 years that’s a promise you

can trust

• No Fault - for any reason, including but not limited to installation error, vandalism or act of God

• Tomorrow - replacement product is shipped at Securitron's expense, next day air if needed

• Hassle Free - No product registration is required

www.securitron.com/warranty

This manual suits for next models

Table of contents

Other Assa Abloy Door Opening System manuals

Assa Abloy

Assa Abloy Corbin Russwin PED5800 Series User manual

Assa Abloy

Assa Abloy Rixson Smok-Chek VI Quick guide

Assa Abloy

Assa Abloy Besam SP33-M User manual

Assa Abloy

Assa Abloy Norton 5500 Series User manual

Assa Abloy

Assa Abloy Norton 6300 Pull Side Series Quick guide

Assa Abloy

Assa Abloy Corbin Russwin PED5800 Series User manual

Assa Abloy

Assa Abloy SARGENT 1431 Series User manual

Assa Abloy

Assa Abloy SECURITRON DEM680E Series Manual

Assa Abloy

Assa Abloy 5800 ADAEZ PRO User manual

Assa Abloy

Assa Abloy SARGENT 268 Series User manual

Assa Abloy

Assa Abloy Norton 7500H Series User manual

Assa Abloy

Assa Abloy Norton 6000 Series Installation manual

Assa Abloy

Assa Abloy NORTON RIXSON 1600 Series User manual

Assa Abloy

Assa Abloy Norton PR7500 User manual

Assa Abloy

Assa Abloy DC130 User manual

Assa Abloy

Assa Abloy G-CO-C User manual

Assa Abloy

Assa Abloy SARGENT 278 Series User manual

Assa Abloy

Assa Abloy Adams Rite 3700 User manual

Assa Abloy

Assa Abloy SARGENT 2900 FIREGUARD User manual

Assa Abloy

Assa Abloy Norton 7570 Series User manual

Assa Abloy

Assa Abloy DC3210 User manual

Assa Abloy

Assa Abloy Yale 3000 Series User manual

Assa Abloy

Assa Abloy G-S User manual

Assa Abloy

Assa Abloy Norton 5700P Series User manual

Popular Door Opening System manuals by other brands

Pamex

Pamex KT-INP35 Installation instruction

Label

Label NEPTIS/LE installation manual

Cal-Royal

Cal-Royal N-F77CVR Installation instruction

Scrigno

Scrigno OPEN1000 Assembly manual

TriMark

TriMark UM 34 instructions

BFT

BFT WIND RMB 130B 200 installation manual

Alecto

Alecto ADI-250 user manual

Besam

Besam Swingmaster MP Installation, adjustment and maintenance instructions

CRL

CRL SENIOR PRIMA manual

GAL

GAL MOVFR Quick setup

Olide

Olide 120B installation manual

Normstahl

Normstahl IDO7 installation manual

Häfele

Häfele Finetta T 70 VF manual

AGS

AGS D-PL Instructions for fitting, operating and maintenance

Stanley

Stanley MA900ñ Installation and owner's manual

WITTUR

WITTUR Hydra Plus UD300 Instruction handbook

Alutech

Alutech TR-3019-230E-ICU Assembly and operation manual

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and OPERATING AND INSTALLATION Manual