Assa Abloy RIXSON W73 User manual

ISW73 07/21

Model W73 Overhead Concealed Closer

Non-Hold Open and Hold Open

Wood Frame Installation Instructions

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Phillips

Screwdriver

Level Tape

Measure

Framing

Square

Hex Wrenches Plumb Bob

Grout

5/16" 3/8"

Hammer Drill Spreader

Tool Hammer

Flathead

Screwdriver

3/16"

for Wood

Pencil

1/4-20

for Metal

AND

Drill

Pour la version francaise voir www.nortondoorcontrols.com.

READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.

This product can expose you to lead which is known to the state of

California to cause cancer and birth defects or other reproductive harm.

For more information go to www.P65warnings.ca.gov.

WARNING

Slider

(90253)

Optional Hold Open

Assembly (90254)

Closer Body

73 LAP or

PH73 LAP (ADA)

Cover Plate

70202- (nish)

Wood Mounting Clip

(90267)

Wood

Mounting

Clip (90266)

Wood Mounting

Clip (90256)

Arm

70218- (nish)

Track

(90239)

Model W73, Center Pivot Hung

Tools Needed

Non Hold Open

Stop Block

(90255)

Components

(Supplied fasteners shown on page 3)

Pivot Kit

70224KIT- (nish)

Slider Centering

Hub (70219)

Retrot Track Spacer and

Screws, Optional (90260)

Not for new installation. Replacement

only. Consult factory.

INCH

X.X

X.XX

X.XXX

ANGLES

FRACTIONS

SURFACE FINISH

UNLESS OTHERWISE

SPECIFIED TOLERANCES

.03

.01

.005

0°30'

1/64

NOTES:

MATERIAL AND MANUFACTURING PROCESS MUST COMPLY WITH

ASSA ABLOY AMERICAS PRODUCT COMPLIANCE SPECIFICATION

DOCUMENT ID# D001117360.

DRAWN BY

matbai

MATERIAL

SEE BOM

V10_7/16/2020

SURFACE/FINISH

THIRD ANGLE

PROJECTION

HEAT TREATMENT

DRAWING COMPLIES

WITH ASME Y14.5M - 1994

NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR

TECHNICAL INFORMATION

The material disclosed herein is the confidential and

proprietary information of

ASSA ABLOY Accessories and Door Controls Group, Inc.

(the “Company”). This drawing and/or technical

information is issued in confidence for engineering

information only and may not be reproduced or used to

manufacture anything, including the items shown or

referred to hereon, without direct written permission from

the Company. This drawing and/or technical information

is the property of the Company and is loaned for mutual

assistance to be returned when its purpose has been

served or upon the request of the Company.

LEGACY ID

SHEET

Rixson70_OHC_RetroFit

Rixson

CONFIGURATION

D001151786-006

DRAWING NUMBER (ALT ID)

VOLUME

2057.621 in³

SURFACE AREA

4464.737 in²

SIZE

DATE CREATED

03/11/2021

duslaw

REV

SCALE

1:3

DOCUMENT ID

D001151786-006

MASS

0.041 lb

Monroe DC, NC

ASSA ABLOY Accessories and

Door Controls Group, Inc.

Mounting Hardware Door / Frame Drill

Closer, Top Pivot and Bottom Pivot:

#14 x 1-1/2" Wood 3/16" (4.76mm)

Closer, Top Pivot and Bottom Pivot:

1/4-20 x 5/8" Metal Drill #7 (.201 dia. or 5.10mm)

Tap 1/4-20

Track:

#14 x 1-1/4" Aluminum or Wood 3/16" (4.76mm)

Track:

1/4-20 x 7/16" Hollow Metal Drill #7 (.201 dia. or 5.10mm)

Tap 1/4-20

ISW73 07/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W73, Wood Frame

Before You Begin:

IMPORTANT:

• The Americans with Disabilities Act (ADA)

requires that doors having door closers have an

opening force not to exceed 5 lbf.

• Door closer’s power size adjustment feature

may require adjustment to its lowest setting to

comply with ADA opening force guidelines.

• ADA compliant closers may not latch doors,

manufacturer does not guarantee latching on

lower opening force settings.

• An improperly installed or incorrectly adjusted door closer may cause property damage or personal injury and

will void product warranty.

• To avoid personal injury, DO NOT DISASSEMBLE THIS DOOR CLOSER BODY.

• Door closers must be securely fastened to a prepared door and frame with fasteners provided.

• HOLD OPEN option not permitted to be installed in re door assemblies.

Contents

Important.............................................................................................. 2

Before You Begin ....................................................................................... 2

Mounting Hardware and Drill Table ..................................................................... 2

Supplied Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Pivot Installation ....................................................................................... 4

Track Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Closer Installation ...................................................................................... 7

Adjustments ........................................................................................... 9

Closer and Pivot, Wood Frame Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

• A separate Rixson Surface Checkmate®or

other door stop, supplied by others, is strongly

recommended to avoid damage to door closer

in heavy abuse applications.

• Top pivot must be plumb with bottom pivot

and door must swing freely before door closer

is installed.

• Door and frame must be reinforced for

attaching screws.

• All dimensions are given in inches (millimeters).

ISW73 07/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W73, Wood Frame

Supplied Fasteners

Closer Screw Pack

(90241)

Closer Track Screw Kit

(90242)

Arm Screw Pack

(70251-nish)

Bottom Pivot Screw Pack

(70243)

Top Pivot Screw Pack

(70242-nish)

Cover Plate Screw Pack

(90278-nish)

1/4-20 x 5/8"

PFHMS

Pivot

#14 x 1-1/2"

PFHWS

Pivot

1/4-20 x 5/8"

PFHMS

Pivot

#14 x 1-1/2"

PFHWS

Pivot

3/8-16 Female

Threaded

Drop-in Anchor

3/8-16 x 2-1/4"

SHCS

Base Plate

8-32 x 1/4"

PFHUCMS

Finish Plate

6-32 x 1/4"

PFHMS

Cover

1/4-20 x 5/8"

PFHMS

Closer Body

10-24 x 3/8"

SHSS

Arm Attach

1/4-20 x 7/16"

PFHUCMS

Track

#14 x 1-1/4"

PFHWS

Track

10-24 x 1-1/2"

SHCS

Arm Clamp

1/4-20 x 1/2"

PFHMS

Arm Attach

#14 x 1-1/2"

PFHWS

Closer Body

5/32"

Hex

Wrench

3/32"

Hex

Wrench

1/8"

Hex

Wrench

3/16"

Hex

Wrench

Conical

Washer

Arm Attach

ISW73 07/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W73, Wood Frame

A. Prepare frame and door.

1. Using supplied templates, prepare and

mortise door and head jamb for pivot set.

(Figure 1)

2. Conrm all cutout dimensions for closer.

Installation

B. Install wood mounting clips.

1. Drill pilot holes into frame.

2. Install clips with four (4) #14 x 1-1/2"

wood screws. (Figure 2)

C. Install top pivot set.

1. Install jamb portion in prepared frame with one

(1) #14 x 1-1/2" wood screw into frame and one

(1) 1/4-20 x 5/8" machine screw into mounting

clip. (Figure 3)

2. Install door portion in prepared door with

three (3) #14 x 1-1/2" wood screws or 1/4-20 x

5/8" machine screws. (Figure 3)

3. Attach nish plate to jamb portion with two (2)

8-32 x 1/4" machine screws. (Figure 3)

Top Pivot

Pivot Point

Finish Plate

Door Portion

Jamb Portion

Top of Door

Wood Frame

Bottom of Door

Figure 1

Figure 3

Figure 2

ISW73 07/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W73, Wood Frame

Figure 4 Bottom Pivot

Base Plate

Drop-in Anchor

(Installed In Floor)

Base Plate Screw

Door Portion

(Installed in

Mortised Door)

D. Install bottom pivot set.

Pivot Point

Figure 5

IMPORTANT: Pivot point of bottom pivot must be

plumb with top pivot point. Be sure to properly locate

and mark pivot center point of bottom base plate.

1. Install door portion into prepared door with four (4)

1/4-20 x 5/8" machine screws or #14 x 1-1/2" wood

screws. (Figure 4)

NOTE: Depth of mortise in door bottom will

determine clearance.

2. Using a plumb bob attached to top pivot, locate and

mark position of base plate on oor.

3. Drill 3/4" dia. x 1-3/4" (19 x 44mm) deep hole in oor

on center of pivot point for base plate mounting.

IMPORTANT: It is critical to door alignment and

proper frame clearance that this anchor hole is

positioned within 1/32" of true plumb alignment

with the top jamb portion pivot point.

4. With open side up, place drop-in anchor into oor

hole. If necessary, tap lightly with hammer until

anchor is at bottom of hole.

NOTE: Clean all concrete dust from hole before

installing drop-in anchor.

5. Set anchor by striking spreader tool with hammer

until the sleeve of the anchor is fully expanded.

(Figure 5)

6. Insert provided base plate screw into anchor to plug

opening.

NOTE: Apply grease to base plate screw to prevent

grout from sticking to screw and to facilitate

removal.

7. Grout anchor into place. After grout has set, remove

base plate screw.

8. Place base plate over anchor and securely fasten to

oor with base plate screw.

9. If using a threshold, install it at this time.

Installation

ISW73 07/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W73, Wood Frame

Figure 7

F. Assemble track.

1. Slide track components into track.

(Figure 11)

NOTE:

• All track components must be placed in

track before installing track into door.

• Insert slider into track rst.

• Stop block (or optional hold open) should

be last component at hinge side of door.

• The longer end of slider should be pointed

towards hinge side of door.

Figure 6

Non Hold Open Track Components

Optional Hold Open Track Components

E. Hang door.

1. Ensure pivot stud is fully retracted into pivot

by turning pivot adjustment screw counter

clockwise with a athead screwdriver. (Figure 6)

2. With door in open position about 90° to jamb,

carefully t door onto bottom pivot at a slight

angle. (Figure 7)

3. Tip door into vertical position aligning frame

portion pivot stud to door portion hole.

(Figure 8)

4. With top pivot stud aligned with door portion

hole, use a athead screwdriver to turn pivot

adjustment screw clockwise to extend pivot

stud into door pivot portion. (Figure 9)

IMPORTANT: Fully tighten adjustment screw to

ensure pivot stud is fully extended into door

portion. There is a door tipping hazard until

door is held vertical by pivot stud.

5. Verify frame is square by using a framing square.

Gaps between door and frame should be

consistent. Gap should be 1/8" (3mm) at jamb

and header. (Figure 10)

NOTE: Door should swing freely.

• If vertical height adjustment is necessary,

use shims between door bottom and

bottom pivot portion to increase clearance.

• To decrease clearance, increase mortise in

bottom of door.

• To remove door, retract pivot stud and tip

door out of vertical position then lift door

from bottom pivot.

Pivot Stud

Pivot Adjustment

Screw

Slider

1/8"

()3

CCW

Pivot Adjustment

Screw

Figure 9 Figure 10

Figure 11

Figure 8

Installation

ISW73 07/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W73, Wood Frame

G. Install track to door.

1. Make sure slider and track

components are installed prior to

installing track to door. See Step F.

2. Install track into top of door using

either four (4) 1/4-20 x 7/16" machine

screws for metal doors or four (4)

#14 x 1-1/4" wood screws for wood

doors. (Figure 12).

NOTE: If necessary, use optional

retrot spacer (replacement

application only, consult factory).

Frame Rabbet

1/4-20 x 5/8 FHPMS

H. Install closer.

1. Install closer into wood mounting

clips with four (4) 1/4-20 x 5/8"

machine screws. (Figure 13)

NOTE: Mounting plate should be

ush with frame rabbet.

I. Install cover plate.

1. Install cover plate to closer body with

six (6) 6-32 x 1/4" machine screws.

(Figure 14)

6-32 FHPMS

(6 each)

Figure 13

Figure 14

1. Attach arm to closer shaft with

1/4-20 x 1/2" machine screw and

washer. Tighten securely. (Figure 15)

NOTE: Ensure countersink recess

side of arm faces down.

2. Insert 10-24 x 1-1/2" socket head cap

screw into arm and clamp arm tightly

to pinion square. (Figure 15)

Optional

Retrot Track

Spacer

1/4-20 x 7/16 FHPMS (4 each)

or 14 x 1-1/4 FHPWS (4 each)

Hinge

Side

Arm Clamp

Screw Arm Screw and

Conical Washer

Countersink

Recess

Figure 15

Figure 12

J. Attach arm to closer.

Installation

ISW73 07/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W73, Wood Frame

Slider

Centering Hub

Slider

Arm Attach

Screw

Adjustment Set Screw

Adjustment

Set Screw

Adjustment

Set Screws

Adjustment Hex Door

Frame

Figure 17

Figure 16

Figure 18 Figure 19

K. Attach arm to track.

1. With provided 1/8" hex wrench, completely

tighten latch and sweep valves by turning

clockwise. This will allow for an easier closer-

to-door connection. (Figure 15)

CAUTION: Arm will be under strong spring force

to return if valves are not tightened completely

closed.

2. Open door to about 45° then rotate arm over

to door.

NOTE:

• With latch and sweep valves tightened,

arm will maintain position.

• If door is opened beyond 45°, backcheck

may need to be adjusted counter

clockwise to easily rotate arm to door

position.

3. Install slider centering hub through arm into

slider. (Figure 16)

NOTE: Countersink recess should face up.

4. Align hub initially as shown and insert two

(2) 10-24 x 3/8" adjustment set screws. Turn

both set screws just enough to retain slider

centering hub. Do not tighten rmly at this

time. (Figure 17)

NOTE: Align square shank of slider with

square in centering hub for proper tment.

5. Insert 1/4-20 x 3/4" at head socket hex screw

and tighten.

6. Open latch and sweep valves to allow door to

close and observe door and frame alignment.

If door is not centered in frame when closed,

reopen door and use 5/16" hex wrench to

rotate slider centering hub until door is

centered. (Figure 18)

NOTE:

DO NOT fully open valves. Valves will leak.

Door should be centered in frame when in

closed position. Adjust slider centering hub

with hex wrench until door and frame are

aligned properly then tighten adjustment

set screws.

7. When door is completely aligned in frame

tighten both adjustment set screws.

Sweep

Latch 1 = Left Hand

Latch 2 = Right Hand

Backcheck

Installation

ISW73 07/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W73, Wood Frame

Adjustments

Latch SpeedBackcheck Sweep Speed

Speed Adjustment

Use provided 1/8" hex wrench to adjust sweep,

latch and backcheck valves to control speed of

door. (Figure 20)

NEVER completely close backcheck valve.

NEVER use backcheck as a dead stop.

NEVER fully open valves. Valves will leak.

Do not use a power drill.

Warranty will be void.

Closing Force Adjustment

If additional force is needed, use 3/8" hex

wrench to adjust closing force. (Figure 21)

Use spring adjustment screw that corresponds

with hand of swing. (Figure 20)

Do not use a power drill.

Warranty will be void.

All 73 Series closers are factory set to minimum

force. Adjust closer as necessary for more force

taking into consideration door size, weight,

positive room pressure, etc.

5° 5°

0°

75°

Figure 20

Figure 21

Spring Power Adjustment for Closing Force

(Closer shipped at lowest setting)

Model PH73DCP Model 73DCP

Closer

Size Description Approx # of

360° Turns

Closer

Size Description Approx # of

360° Turns

ADA <5 lbs

Opening Force 0 1 2 - 3 lbs

Closing Force 0

12 - 3 lbs

Closing Force 15 2 3 - 5 lbs

Closing Force 15

23 - 5 lbs

Closing Force 30 3 5 -8 lbs

Closing Force 35

35 - 8 lbs

Closing Force 50 4 8+ lbs

Closing Force 50

Set

Screws

Locking Ta b

Slider

Optional Hold Open Adjustment

1. Insert locking tab of hold open assembly

into track slider. (Figure 22)

NOTE: Hold open assembly should be on

hinge side of track slider.

2. Open door to desired hold open position.

3. Tighten hold open set screws to lock down

hold open assembly. (Figure 22)

4. Pull door in closing direction to disengage

hold open assembly and track slider.

5. Adjust hold open by turning adjustment

screw with provided 3/16" hex wrench.

(Figure 22)

NOTE: THIS FEATURE CANNOT BE USED ON

FIRE-RATED DOORS

You’ve now installed the Model W73 Overhead Concealed Closer.

Figure 22

Holding Force Adjustment Screw

ISW73 07/21

Rixson is a brand associated with ASSA ABLOY Accessories and Door Controls Group, Inc., an ASSA ABLOY Group company.

part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Rixson Technical Product Support:

Monroe, NC 28112 USA

Phone: 800.438.1951 ext: 6030

TechSupport.Rixson@assaabloy.com

rixson.com

Troubleshooting

Symptom Cause Remedy

Door won’t latch

Spring tension not strong enough Increase opening force.

See Adjustments section.

Latch speed control not fast enough Adjust latch speed valve.

See Adjustments section.

Door hung on products other than

center pivots

Send template for hanging means

to factory. A new installation sheet

is required. Closer will need to be

relocated.

Arm is not preloaded See Step I. Attach Arm to Door

Door is too difcult to open Spring tension is set too strong Decrease opening force.

See Adjustments section.

Table of contents

Other Assa Abloy Door Lock manuals

Assa Abloy

Assa Abloy Union CodeGUARD 5 Assembly instructions

Assa Abloy

Assa Abloy ESA500 Installation manual

Assa Abloy

Assa Abloy KESO KEK i-handle S Operator's manual

Assa Abloy

Assa Abloy IKON VERSO CLIQ User manual

Assa Abloy

Assa Abloy ZI IKON eCLIQ N109 User manual

Assa Abloy

Assa Abloy 81 C Series User manual

Assa Abloy

Assa Abloy R10 User manual

Assa Abloy

Assa Abloy ML22HPH User manual

Assa Abloy

Assa Abloy Yale YDME 50 Pro User manual

Assa Abloy

Assa Abloy eCLIQ User manual

Assa Abloy

Assa Abloy Sargent AD-PE8600 User manual

Assa Abloy

Assa Abloy Yale AYRD110 User manual

Assa Abloy

Assa Abloy SARGENT 80 Series User manual

Assa Abloy

Assa Abloy Corbin Russwin ED5200N Series User manual

Assa Abloy

Assa Abloy Abloy EL648 User manual

Assa Abloy

Assa Abloy Effeff Technilock L4 Series User manual

Assa Abloy

Assa Abloy Corbin Russwin ED3400 Series User manual

Assa Abloy

Assa Abloy Corbin Russwin Access 800 TCAC2 Series Installation manual

Assa Abloy

Assa Abloy Yale YMI70A User manual

Assa Abloy

Assa Abloy SARGENT IN Series User manual

Assa Abloy

Assa Abloy effeff ANYKEY User manual

Assa Abloy

Assa Abloy EMTEK Tubular Monolithic Entry Set User manual

Assa Abloy

Assa Abloy Valencia Hola User manual

Assa Abloy

Assa Abloy MSL sFlipLock check User manual

Popular Door Lock manuals by other brands

We.lock

We.lock SECBNEBL51 instructions

Iseo

Iseo MA1A installation guide

ID Lock

ID Lock 150 user manual

Lockly

Lockly ACCESS TOUCH PRO user manual

iLoq

iLoq G50S user guide

SDC

SDC Z7835 installation instructions

ilco

ilco 452 Installation

Samsung

Samsung shs-h705 user guide

TRU-BOLT

TRU-BOLT 08102017 user manual

CDVI

CDVI 500-LADJ quick start guide

Igloohome

Igloohome Deadbolt 2S Metal Grey Installer/user guide

eSSL

eSSL FL-300 user manual

JAKO

JAKO JKBTNX4 installation guide

Dorma

Dorma MUNDUS PREMIUM GK 50 Mounting instruction

SCOOP

SCOOP Pullbloc 4.1 FS Panik Assembly instruction

Yale

Yale MORTISE 8800 SERIES installation instructions

Siegenia

Siegenia KFV AS3500 Assembly instructions

Saflok

Saflok Quantum ädesē RFID installation instructions