Assa Abloy 8800 Series User manual

8800 Series Mortise Lockset

Knob, Lever, Reﬂections ®,and Security Trims

Installation Instructions

WARNING

This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other

reproductive harm. For more information go to www.P65warnings.ca.gov.

Attention Installer: Any retroﬁt or other ﬁeld modiﬁcation to a ﬁre rated opening can potentially impact the ﬁre rating of the opening,

and ASSA ABLOY makes no representations or warranties concerning what such impact may be in any speciﬁc situation. When retroﬁt-

ting any portion of an existing ﬁre-rated opening, or specifying and installing a new ﬁre-rated opening, please

consult with a code specialist or local code ofﬁcial (Authority Having Jurisdiction) to ensure compliance with all applicable codes and

ratings.

WARNING

80-9086-0026-010 11/23

1-800-235-7482 • www.assaabloy.com

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

#2 Phillips head

screwdriver

1/8" Allen

Wrench

Tools Required

IMPORTANT!

The accuracy of the door preparation is critical for the proper functioning and security of this mortise lock. Misalignment can cause premature wear

and tear and a lessening of security.

Hole saws (See template. Required sizes depend on application.)

A. Mark horizontal line across face of door. 39-15/16" (101cm) is the usual lever height above the ﬁnished

ﬂoor.

B. Align the provided template center on the horizontal line. Before drilling, verify that the backset, door

handing, and side of the door correspond to the side of the template being used.

39 15/16"

(101cm)

Finished Floor

Handing the Latchbolt

A. Insert ﬂat blade screwdriver into cover slot.

B. Pull back on screwdriver until latchbolt extends past base front and rotate the head to the desired position.

If required, adjust the handing for the lockbody.

Handing the Hubs

A. Locate RED MARK on locking piece.

B. Push toggle button slide away from “square spindle hole.”

C. With blade screw driver push RED MARK on slide nearest “square spindle hole.”

D. RED MARK indicates locked side.

2. Verify Handing

1. Mark and Drill Door

1-800-235-7482 • www.assaabloy.com

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

8800 Series Mortise Lockset

Knob, Lever, Reﬂections ®,and Security Trims

Installation Instructions

80-9086-0026-010 11/23

3. Install Lockbody

4. Install Trim

Insert lockbody in door. Ensure the bevel of the latchbolt faces the strike plate. Attach with two #12 x 1"

combination screws. Leave attaching screws loose until the end when all will be tightened securely.

(2) #12 x 1" Combination

Screws

B. Rose Trim

1. Insert outside rose assemby (w/posts) through the door and

into lock.

2. Align and fasten inside mounting plate with two #8-32 x 1"

screws to posts.

3. Tighten screw securely.

4. Align and press rose posts to plastic bushings on mounting

plate.

5. Go to Step 5, Page 5.

C. Square Rose Trim

1. Install cylinder with square collar and square rose trim, same as 4A and 4B.

The square rose and mounting plate needs to be oriented correctly during installation. Failure to do so causes roses that

are crooked on the door, forcing the installer to remove and reinstall the parts. The proper orientation for the plastic

rose-mounting inserts points in the upward direction. The rose is oriented with the slot facing the hinge side of the

door.

Outside

Rose Assembly

Mounting Plate

(2) #8-32 x 1" Attaching Screws

Rose

(2) Rose

Adapter

A. Install Cylinder

(If applicable)

1. Insert cylinder through the

cylinder collar, door and

into lock.

2. Securely hand tighten

cylinder set screw through

the edge of the lock case.

NOTE: Do not use powered

screw drivers to tighten

cylinder set screw.

Cylinder Collar

Cylinder

Slot in trim must face towards the hinge side of door.

Plastic inserts must

face upwards

Correct orientation shown.

Go to Step 5, Page 5.

1-800-235-7482 • www.assaabloy.com

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

8800 Series Mortise Lockset

Knob, Lever, Reﬂections ®,and Security Trims

Installation Instructions

80-9086-0026-010 11/23

4. Install Trim, continued

D. Escutcheon Trim - All types except SL

1. Insert outside escutcheon assembly (w/posts) through the door

and into lock.

2. Align and fasten inside escutcheon with #10-24 x 1-1/2" screws

to posts.

3. Align and fasten cylinder through escutcheon(s) and into lock

body. Leave attaching screws loose until the end when all will be

tightened securely.

4. Go to Step 5, Page 5.

Hand tighten

cylinder clamp

screw securely

through the

edge of the

lock case.

(2) #10-24 x 1-1/2" Attaching Screws

Outside

Escutcheon

Trim

Assembly

Inside Escutcheon Trim

Assembly

Cylinder

E. SL Escutcheon Trim

1. Insert outside escutcheon assembly (with posts)

through the door and into lock.

2. Align and fasten inside escutcheon with #10-24 x 1-1/2"

screws to posts.

3. Align and fasten cylinder and cylinder collar through

escutcheon(s) and into lock body.

Cylinder Collar

Cylinder

Outside SL Trim Assembly

(2) #1024 x 11/2" Attaching Screws

Inside SL Trim Assembly

F. Single Sided Active Trim

1. Align and securely fasten mounting plate and

#8-32 x 1" attaching screws to threaded posts in

lockbody.

2. Align and press rose posts to plastic bushings on

mounting plate.

3. Assemble rose adapter (not used on Reﬂections® ) in

rose assembly.

4. Disassemble split spindles prior to installing into lock.

Insert stepped spindle ﬁrst, then insert non-stepped

spindle. Insert lever on spindle assembly and tighten

set screw located in the lever.

5. See Install Armor Front, Page 7, to complete

installation.

Mounting Plate

(2) #8-32 x 1" Attaching Screws

Rose Assembly with posts

Plastic Bushing

Split Spindle

Lever

Rose Adapter

1-800-235-7482 • www.assaabloy.com

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

8800 Series Mortise Lockset

Knob, Lever, Reﬂections ®,and Security Trims

Installation Instructions

80-9086-0026-010 11/23

4. Install Trim, continued

G. 838A Dummy Trim

1. Insert outside rose assembly (w/posts) through the door

and align and fasten inside mounting plate with screws.

2. Align and press rose posts to plastic bushings on mounting

plate. Slide spindle bar through edge of door, making sure

the screw hole is in the top postion.

3. Insert outside lever assembly through rose assembly and

into square hole in spindle bar.

4. Assemble inside lever to outside lever assembly

and tighten set screw located in inside lever.

5. Attach dummy front to spindle bar with #12-24 x 1"

attaching screw.

Mounting Plate

(2) #8-32 x 1" Attaching Screws

Outside

Rose Assembly

(2) Plastic

Bushing

Outside

Lever Assembly

(2) Rose

Adapter

Set Screw

Inside

Lever

Spindle Bar

#12-24 x 1" Screw Dummy Front

Rose

I. 855 Dummy Trim

1. Align mounting plate over the intersection of previously

marked horizontal line (lever height) and vertical backset

centerline.

2. Mark the hole and drill with a 3/8" drill.

3. Insert sex nut into door and thread mounting plate bolt

into sex nut.

4. Use lever hadle to tighten spindle. Check that the lever

will be level when installed.

5. Drill pilot holes and fasten with four (4) attaching

screws.

6. Slide Rose and Rose Adapter onto spindle.

7. Attach Lever and tighten set screw securely.

Mounting Plate

(4) #10 x 1-1/2” Attaching Screws

Rose Assembly

Rose Adapter

Plastic Bushing

Set Screw

Lever

Sex Nut Notice the orientation of the small holes

H. 838B Dummy Trim

1. Insert outside rose assembly (w/posts) through the door

and align and fasten inside mounting plate with screws.

2. Align and press rose posts to plastic bushings on mounting

plate. Slide spindle bar through edge of door, making sure

the screw hole is in the top postion.

3. Insert outside lever assembly through rose assembly and

into square hole in spindle bar.

4. Assemble inside lever to outside lever assembly and tighten

set screw located in inside lever.

5. Insert strike box and then attach strike to spindle bar with

#12-24 x 1" screw. Use remaining #12 x 1" combination

screw to attach the top of strike to the door.

Set

Screw

#8-32 x 1"

Attaching Screws

Outside Lever Assembly

Inside Lever

Rose

Inside Mount-

ing Plate

Spindle

Bar

Strike

Box

Strike

Screws

Outside Rose Assembly

(2) Rose Adapter

(2) Plastic

Bushing

1-800-235-7482 • www.assaabloy.com

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

8800 Series Mortise Lockset

Knob, Lever, Reﬂections ®,and Security Trims

Installation Instructions

80-9086-0026-010 11/23

4. Install Trim, continued

J. Reﬂections® Lever 855 Dummy Trim

1. Align mounting plate over the intersection of previously

marked horizontal line (lever height) and vertical backset

centerline.

2. Mark holes through mounting plate. Drill pilot holes and fasten

with two (2) attaching screws.

3. Slide Rose onto spindle.

4. Attach Lever and tighten set screw securely. Check that the

lever will be level when installed.

Mounting Plate

(2) #10 x 1-1/2" Attaching Screws

Rose Assembly

Set Screw

Lever

Inside Spindle

with ramp

Outside Lever Assembly

1/2 Turn Gap

A. Prepare Lever or Knob Assembly - Not including SL

Trim

1. Remove from packaging and remove inside lever/knob.

2. Unscrew the inside spindle from the outside lever assembly 1/2

turn and align the ramp in the horizontal position before inserting

into the lock.

B. Install Lever Assembly or Knob Assembly on Rose and Escutcheon Trims - Not including

SL Trim

Outside

Lever Assembly

(2) Plastic

Bushing

Inside Lever

Set Screw

1. Insert outside lever assembly through the

rose or escutcheon trim and through the

lockbody.

2. Insert inside lever onto the outside lever

assembly spindle and tighten inside lever

set screw.

5. Install Lever or Knob Assembly

1-800-235-7482 • www.assaabloy.com

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

8800 Series Mortise Lockset

Knob, Lever, Reﬂections ®,and Security Trims

Installation Instructions

80-9086-0026-010 11/23

6. Install Thumbturn Assembly

7. Install IND and CIND Assembly on the door

Note: Thumbturn Assembly may be used on opposite sides of the door, dependant on the function.

OR OR

Standard

Thumbturn

Assembly

Reﬂections®

Thumbturn

Assembly

1. Drill holes indicated for the thumbturn to be

installed. (See template 7088-1009).

2. Install the lockbody in the mortise pocket (see

Install Lockbody, Page 2).

3. Align the mechanism shaft through the Ø5/8"

hole and into the square hub in the lockbody.

4. Install and tighten attaching screws.

Square Rose

Thumbturn

Assembly

Note: CIND Indicators may be used in conjunction with the thumbturn and most thumbturns are mounted on the egress side of the

door.

1. Drill holes indicated for the function to be installed (see template 7088-1009).

2. Install the lockbody in the mortise pocket (see Install Lockbody, Page 2).

3. Align the CIND Assembly through the Ø5/8" hole and into the square hub in the lockbody.

4. Install the cylinder securely and fasten the cylinder clamp screw (see Install Cylinder, Page 2).

IND Assembly

Cylinder

CIND Assembly

1-800-235-7482 • www.assaabloy.com

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

8800 Series Mortise Lockset

Knob, Lever, Reﬂections ®,and Security Trims

Installation Instructions

80-9086-0026-010 11/23

8. Install Armor Front

1. Align armor front to front of lockbody and attach screws.

(2) #8-32 x 1/4" FHPMS U-Cut

Attaching Screws

Armor Front

9. Install Strike

1. Attach strike to jamb using #12 x 1"

combination screws.

Door Frame

Door Stop

Strike Box

(When Req'd)

Strike

1/2 Door

Thickness

#12 x 1"

5/8" (16)

2-7/16"

(62)

Combination Screws

1-800-235-7482 • www.assaabloy.com

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

80-9086-0026-010 11/23

Table of contents

Other Assa Abloy Door Lock manuals

Assa Abloy

Assa Abloy Yale Delayed Egress User manual

Assa Abloy

Assa Abloy KESO User manual

Assa Abloy

Assa Abloy EL460 User manual

Assa Abloy

Assa Abloy LE932 User manual

Assa Abloy

Assa Abloy Sargent PE8900 Series User manual

Assa Abloy

Assa Abloy Corbin Russwin ED8400 Series User manual

Assa Abloy

Assa Abloy Adams Rite 3000SE User manual

Assa Abloy

Assa Abloy Securitron DSB Series User manual

Assa Abloy

Assa Abloy 179E User guide

Assa Abloy

Assa Abloy Lockwood Cavity Lock User manual

Assa Abloy

Assa Abloy HES 9400 Series User manual

Assa Abloy

Assa Abloy EL580 User manual

Assa Abloy

Assa Abloy Liscio User manual

Assa Abloy

Assa Abloy Corbin Russwin TL3700 Series User manual

Assa Abloy

Assa Abloy multi-t-lock Code Handle Window User manual

Assa Abloy

Assa Abloy effeff 827A-IP User manual

Assa Abloy

Assa Abloy PEMKO LP200 Series User manual

Assa Abloy

Assa Abloy Connect 50 User manual

Assa Abloy

Assa Abloy effeff ANYKEY User manual

Assa Abloy

Assa Abloy Corbin Russwin SE LP10 9600 Series User manual

Assa Abloy

Assa Abloy Pemko 4131RL User manual

Assa Abloy

Assa Abloy Yale Real Living YRL210 Technical specifications

Assa Abloy

Assa Abloy Yale Doorman User manual

Assa Abloy

Assa Abloy TD0192 User manual

Popular Door Lock manuals by other brands

We.lock

We.lock SECBNEBL51 instructions

Iseo

Iseo MA1A installation guide

ID Lock

ID Lock 150 user manual

Lockly

Lockly ACCESS TOUCH PRO user manual

iLoq

iLoq G50S user guide

SDC

SDC Z7835 installation instructions

ilco

ilco 452 Installation

Samsung

Samsung shs-h705 user guide

TRU-BOLT

TRU-BOLT 08102017 user manual

CDVI

CDVI 500-LADJ quick start guide

Igloohome

Igloohome Deadbolt 2S Metal Grey Installer/user guide

eSSL

eSSL FL-300 user manual

JAKO

JAKO JKBTNX4 installation guide

Dorma

Dorma MUNDUS PREMIUM GK 50 Mounting instruction

SCOOP

SCOOP Pullbloc 4.1 FS Panik Assembly instruction

Yale

Yale MORTISE 8800 SERIES installation instructions

Siegenia

Siegenia KFV AS3500 Assembly instructions

Saflok

Saflok Quantum ädesē RFID installation instructions