AQUATECH Strike Flash User manual
Strike Flash Housing
Instruction Manual
Flash Mount- Bolts to the top of your Sport Housing
using two M5x10 bolts.
Flash Bulkhead- The (black) dry connector located
on the side of your Flash Sport Housing. The ash
bulkhead is only waterproof if the cap is on or if the
sync cord is connected.
Sync Cord- The 16 inch (400mm) cable that
connects between your Flash Sport Housing and
Camera Sport Housing. This cord is only waterproof
if caps are screwed on or if it is connected to your
Flash Sport Housing and Camera Sport Housing.
Camera Hot Shoe- This piece connects to the hot
shoe of your camera then to the Flash Bulkhead
wires on the inside of your housing. This piece is
fragile so handle with care.
6mm Hex Key- This tool is used for tightening down
the Flash Sport Housing to the mount.
5mm Hex Key- This tool is used to bolt down the
Backplate.
4mm Hex Key- This tool is used to bolt down the
Flash Mount.
FEATURES:
Flash Housing- Clear casing that suits
your professional ash.
Flash Bolts- Included are four M6x18
bolts. Three are used for sealing the Flash
Sport Housing and there is one extra
included for back up.
Grey Sealing O-Ring- This o-ring seals
between the Backplate and Flash Sport
Housing.
Instructions:
Place the ash inside the Flash Housing, lock
into place using the ash hot shoe lock on
your ash. Ensure the main O-Ring is in place
and clear from any dirt or grit. Tighten the back
plate onto the Flash Housing with the M6x18
Bolts, take care to evenly tighten and DO NOT
over tighten. You should see an even amount
of pressure on the O-Ring completely around
the seal.
Attach the Flash Mount to the centre of your
Sport Housing using the two supplied bolts
and the 4mm Hex key. Place the Flash Housing
into the mount and lock into place using the
bolt located in the base of the Flash Housing.
Remove the ash Sync bulk head caps from
both the ash housing and the Sport Housing.
Please ensure there is small O-Ring sitting
in the groove of these ash sync Bulk heads.
Connect the Sync Cord to the ash Sync bulk
head on both the Sport Housing and Flash
Housing. Applied downward pressure to lock
into place and tighten via screwing the sync
lead cap into place. Please Take care not to
over tighten as this may split the O-Ring.
Connect the Camera Hot Shoe connector
into the internal ash connection of the
Sport Housing. These are Male / Female pin
conguration and should be connected with
care as parts are very fragile.
Before placing your camera inside the Sport
Housing, slide the Hot Shoe connector onto the
Hot Shoe of your camera. Carefully slide your
camera into place and test the ash before
entering the water.
IMPORTANT:
-Do not over tighten the Backplate when
sealing. Doing so can damage the Flash Sport
Housing.
Other AQUATECH Camera Accessories manuals
AQUATECH
AQUATECH EDGE Pro Fuji X-T5 User manual
AQUATECH
AQUATECH EDGE User manual
AQUATECH
AQUATECH Pocket Wizard User manual
AQUATECH
AQUATECH Scout & Shadow User manual
AQUATECH
AQUATECH EDGE User manual
AQUATECH
AQUATECH P Series User manual
AQUATECH
AQUATECH REFLEX User manual
AQUATECH
AQUATECH EVO III User manual
AQUATECH
AQUATECH P Series User manual
AQUATECH
AQUATECH Sync Transmitter Housing User manual
Popular Camera Accessories manuals by other brands
Viltrox
Viltrox EF-NEX Mount instructions
Calumet
Calumet 7100 Series CK7114 operating instructions
Ropox
Ropox 4Single Series User manual and installation instructions
Cambo
Cambo Wide DS Digital Series Main operating instructions
Samsung
Samsung SHG-120 Specification sheet
Ryobi
Ryobi BPL-1820 Owner's operating manual
