Apollo 55100-021 MAR User manual

Conventional Marine Indoor

Manual Call Point Installation Guide

General

The Conventional Marine Indoor Manual Call Point-Red, part number 55100-021 MAR,

model number MCP2A-R470SF-A071-02 is supplied with a backbox for surface mounting.

The call point is ‘Type A’ and is suitable for indoor use only. For ﬂush mounting, a standard

electrical outlet box with a minimum depth of 25mm is required.

Installation – General

The installation must conform to BS5839: Part 1 (or applicable local codes).

Installation

1. Fit the backbox (Fig 1) to the wall.

2. Run the cables into the backbox and connect them to the terminal block as shown in

Fig 2. Ensure that functional earth/screen continuity is maintained.

3. Unlock the small front cover by inserting the forked key and pushing it home. Remove

key, slide the cover down and remove the deformable element. Connect the terminal

block as shown in Fig. 2, secure the call point to the backbox and reﬁt the deformable

element as required. Finally, replace the front cover in the reverse order in which it was

removed and push it up until it locks.

39214-589/Issue 1

www.acornfiresecurity.com

Transparent Hinged Cover (ﬂip lid)

To provide additional protection against accidental operation of call points, a transparent

hinged cover, part no. 26729-152 is available.

To prevent against malicious activations of call points, locking tags are also available, part

no. 26729-179.

Please note that the call point does not conform to EN54–11 : 2001 when the hinged cover is

secured with the locking tag.

Commissioning

Test each MCP using the test key provided. Ensure the control panel enters the alarm state.

Wiring Details

All wiring terminals accept solid or stranded cables up to 2.5mm².

Technical data

Maximum Voltage 30VDC

Maximum Switching Current 2A

Alarm Resistor 470 Ω/ 1W

IP rating IP24D

Operating Temperature -10°C to 55°C

Troubleshooting

Before investigating individual units for faults, ensure the system wiring is fault free.

Routine testing

Insert the test key into the hole at the bottom of the call point and push home. Observe

routine test requirements as speciﬁed in the applicable local codes.

Resetting

After testing, reset the call point by removing the test key and pushing up the front cover until

it clicks home.

Important Information

The use of lubricants, cleaning solvents or petroleum based products should be avoided.

Do not over tighten ﬁxing screws.

General Fault Finding

Problem Possible Cause

Control panel reports zone fault Incorrect zone wiring

Detectorremoved

EOL device missing or incorrectly ﬁtted

Control panel reports alarm MCP not reset

Test key not removed

IncorrectEOLdevice

MCP does not activate alarm Incorrect wiring

Incompatiblecontrolpanel

For further information, please refer to PP2419.

Fig 1 Backbox

87mm

765432

470 Ω

765432

Fig 2 Terminal block connections

www.acornfiresecurity.com

This manual suits for next models

Other Apollo Security System manuals

Apollo

Apollo 51000-305 User manual

Apollo

Apollo 55000-278 User manual

Apollo

Apollo REACH WIRELESS RW1500-110APO User manual

Apollo

Apollo REACH WIRELESS RW1500-210APO User manual

Apollo

Apollo REACH WIRELESS RW1500-210APO User manual

Apollo

Apollo 33 404 Operating and maintenance instructions

Apollo

Apollo 51000-357 User manual

Apollo

Apollo XP95 IS User manual

Apollo

Apollo 55000-278 User manual

Apollo

Apollo Marine & Offshore MCP2A-R470SF-A071-02 User manual

Apollo

Apollo REACH WIRELESS RW1900-901APO User manual

Apollo

Apollo REACH WIRELESS RW1000-400APO User manual

Apollo

Apollo Smoke Detector XP95 Operating and maintenance instructions

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual