Amvex GR Series Operating instructions
1
CAUTION: Federal (USA & Canadian) law restricts this device to sell by or on the order of a physician.
OPERATING AND MAINTENANCE MANUAL
0413
0413
1111 Lakeside Drive, Gurnee, IL 60031-4099 | Tel: 1.800.448.0770 | Fax: 847.855.6300
www.ohiomedical.com
25B East Pearce St., Richmond Hill, ON L4B 2M9 Canada | Tel: 905.764.7736 | Fax: 905.764.7743 | www.amvex.com
- CLICK STYLE AND MINI CLICK STYLE -
GAS REGULATORS
Gas Regulator Type:
Liters per minute (LPM)
4 LPM: 04
8 LPM: 08
15 LPM: 15
25 LPM: 25
Optional Colors:
Purple: P
Green: G
Gold: Y
Red: R
Black: B
Silver: S
Chrome Brass: C
Blue (standard): X
GRXX - YYY - (Z)
Connection Type:
CGA Yoke: 870
CGA Nut & Nipple: 540
Femal 1/4” NPT: F4O
Bullnose: BNO
Basic Matrix shown. For more options (flowport, gauge auxiliary ports, etc.) please contact Amvex.
2
THIS DEVICE IS CLEANED FOR OXYGEN SERVICE IN ACCORDANCE WITH CGAPAMPHLET G.4.1.
IMPORTANT: SAFETY INSTRUCTIONS
This manual provides you with important information about the Gas Regulators and should
be read carefully to ensure the safe and proper use of this product.
Read and understand all the safety and operating instructions contained in this booklet.
If you do not understand these instructions, or have any questions, contact your supervisor, dealer or the
manufacturer before attempting to use the apparatus.
Indicates a potentially hazardous situation, which if not avoided, could result in death or
serious injury.
ATTENTION: Indicates a potentially hazardous situation, which if not avoided, could result in minor or
moderate injury.
CAUTION: Indicates a potentially hazardous situation, which if not avoided could result in property
damage.
Receiving Inspection
Remove product from package and inspect for damage. Verify that the model received is in working order. If product
is damaged or incorrect, do not use. Contact your dealer, equipment provider or manufacturer.
ATTENTION: It is very important to allow product to remain in original packaging for 24 hours to
acclimatize to room temperature before use.
User Responsibility
Service of this device should only be performed by properly trained individuals.
This product performs as explained in this manual. This holds true as long as the assembly, use, repair and
maintenance are properly followed according to our instructions. Periodic review of this device is recommended. If
any damage or defects are present, the product should not be used. This includes parts that may have been altered,
contaminated, worn or missing. If any of the above are noted, immediate repair/replacement is required. If this
device is subject to improper maintenance, repair, use and/or abuse leading to malfunction of the device, replacement
is the sole responsibility of the user.
DO NOT attempt to operate this device unless you are properly trained in it use or are
supervised by someone educated on the proper use of the apparatus (REF. CGA Pamphlet
G-4 “Oxygen”). DO NOT use this device on patients who have stopped breathing without
using proper resuscitation equipment.
TO MINIMIZE THE RISK OF EXPLOSION OR FIRE:
• Make sure that the person installing or using the cylinder, Gas Regulator and other oxygen apparatus has clean
hands that are free of hand lotions, petroleum based product, hair spray or any other similar products.
• Inspect the cylinder valve and Gas Regulator thoroughly for dust, oil and grease. DO NOT
USE THE CYLINDER IF OIL OR GREASE ORANY OTHER PETROLEUM-BASED FLAMMABLE
SUBSTANCE IS PRESENT. Inform your gas supplier of this condition immediately.
• DO NOT allow Oxygen or Oxygen equipment to be exposed to fire, heat, sparks, electrical switches or
other possible sources of ignition. DO NOT store or use oxygen equipment at temperatures of less than 0oF
or more than 120oF
• NO SMOKING – Remove matches, cigarettes, lighters and lighter fluids from the patient and from the
oxygen therapy area before administering oxygen. Remove other flammable materials from the area.
• DO NOT allow cylinders to tip or fall. Never allow the temperature of the cylinder contents to exceed
120oF. DO NOT store cylinders near sources of heat or flame
Intended Use
The Amvex Click Style Gas Regulator is used to control the gas pressure of medical compressed gas accurately
under the direction of a healthcare processional. The Gas Regulators are available for both Nut and Nipple or Yoke
style CGA fittings. The units are machined brass finished with an anodized aluminum body. The Amvex Click Style
Gas Regulators are available in a variety of flow rates from 0-4, 0-8, 0-15, 0-25 LPM.
!WARNING:
!WARNING:
!WARNING:
3
Specifications
Gas Regulator Description
1. Swivel Yoke (used on small D and E size cylinders). This connection must have a sealing washer.
2. Nut and Nipple style. There is no sealing washer used with this connection. Tighten this fitting to the larger
cylinder valves with a wrench.
Flow Range Accuracy
0 - 1 LPM +/- 20% from 0-1 LPM
1.5 - 25 LPM +/- 10% above 1 LPM
Inlet pressure range 3000 PSI maximum. Preset 50 PSI +/-10 PSI
Operating Instructions
Inspect the gas cylinder valve for leaks before putting it into service. If a leak is found around the cylinder valve
stem, close the valve, place the cylinder outdoors in a safe area and inform your gas supplier immediately.
Connecting The Regulator To A Cylinder
1. Chain or secure the cylinder to a wall, stand or cart. Remove the protective dust cover from the cylinder valve.
Keep this cover and reinstall it on the cylinder valve if the Gas Regulator is removed and the cylinder is to be
used again.
2. Purge the cylinder valve of foreign materials by opening and closing it. See your oxygen cylinder dealer
for more detailed information.
3. a. If the Gas Regulator has a yoke type inlet connection, be sure that sealing washer is in place on the Gas Regulator yoke
connection. Place the two pins on the Gas Regulator yoke into the matching holes on the cylinder valve. Be sure that the
pointed end of T-handle fits into the small round recess on the opposite side of the valve. Hand tighten the T-handle.
b. If the Gas Regulator has a CGA 540 connection, install the inlet nut on the cylinder valve and tighten with
a wrench.
c. If the Gas Regulator has a Bullnose or DIN inlet nut 477 connection, install the inlet nut on the cylinder valve
and hand tighten.
ATTENTION: Sealing washers should be checked for damage or contamination before each use. If either is
visible, replace immediately. It is recommended that a new seal be used each time the cylinder is changed.
ATTENTION: Fittings attached to auxiliary ports are factory set to ensure proper flow. If user attaches additional fittings to
the auxiliary port, care must be taken to ensure factory setting is maintained, by holding factory fittings in
place with a wrench to keep it from rotating. Flow should be verified whenever changes are made.
Setup For Use
1. Be sure the Gas Regulator is in the “OFF” position by rotating the knob counterclockwise to the “0” position.
2. Stand so that the cylinder valve is between you and the Gas Regulator .
Never stand in front or behind a Gas Regulator when opening the cylinder valve.
Always stand so that the cylinder is between you and the Gas Regulator .
3. Open the cylinder valve very SLOWLY, about one full turn counter clockwise.
4. If you detect a hissing sound, there is a leak in the system. Turn the cylinder off and turn the Gas Regulator on.
This will relieve any built up pressure. Try tightening the Gas Regulator to the cylinder and opening the cylinder
again. If this does not help, shut the system down again and contact a service representative.
5. Adjust the flow rate setting by turning the knob clockwise until the desired setting shows through the window.
NEVER try to remove the Gas Regulator unless the cylinder is off and pressure has been relieved.
At any time the Gas Regulator , cylinder or other apparatus does not operate in its usual or
normal manner, stop using the apparatus and notify your dealer immediately.
ATTENTION: Flow rates are not accurate when a back-pressure of more than 2 PSIG exists downstream of the Gas Regulator
!WARNING:
!WARNING:
!WARNING:
4
Closing The Regulator
1. When you have finished using oxygen, close the system by turning the cylinder valve clockwise to the
“OFF” position.
CAUTION: Oxygen will continue to flow from the outlet orifice assembly until the cylinder valve is
closed (Reference CGA Pamphlet P-14, “Accident Prevention in Oxygen Rich and Oxygen
Deficient Atmospheres”). It is very important to always close the cylinder valve after using.
Removing The Regulator From A Cylinder
1. Close the cylinder valve.
2. Wait for the oxygen to flow out of the Gas Regulator , then turn the knob to the “OFF” position
3. Remove the Gas Regulator from the cylinder by loosening the T-handle or removing the inlet nut.
4. When not attached to a cylinder, store the Gas Regulator in its original container in a clean protected area free
from grease, oil and other contamination.
5. Amvex recommends replacing the sealing washer when the Gas Regulator is mounted to a different cylinder.
Cleaning Instructions
Clean the external surfaces of the Gas Regulator with a damp cloth. If more cleaning is required, return the Gas
Regulator to your dealer.
CAUTION: DO NOT submerse the Gas Regulator in any form of liquid. This will cause damage and
void any warranty on the product.
Troubleshooting
Contact your dealer or the technical support department at Amvex Corporation for assistance if the Gas Regulator does not function.
Maintenance Prevention
Inspect the product before and after use for any damage and ease of operation.
ATTENTION: This regulator is equipped with a relief valve. If you hear a hissing or popping sound coming
from the regulator, close the cylinder valve or gas inlet and contact your dealer. The regulator
relieve valve is not designed to protect any downstream device or apparatus.
CAUTION: Disconnect the Gas Regulator from gas supply before servicing.
Authorized Representative
in the European Union:
EC REP
Oxygen Care Ltd.
2 Holfeld Business Park
Kilmacanogue Co Wicklow
Ireland GR-C-MANUAL 12/10
WARRANTY
Amvex Corporation warrants its Medical Secondary Equipment to be free from defects in material and workmanship
for a period of Five (5) years from the date of shipment. Within the first Twelve (12) months from date of shipment
Amvex will repair or replace any part which is proven to be defective at Amvex’s cost. After the first Twelve (12)
months, Amvex will send the parts to the customer free of charge, but the shipping and installation will be borne by the
Customer. This warranty is valid only when the product has been properly installed according to Amvex specifications,
used in a normal manner and serviced according to factory recommendations. It does not cover failures due to
damage occurring in shipments or failures resulting from accidents, misuse, abuse, neglect, mishandling, alteration,
misapplication or damage that may be attributable to acts of God.
AMVEX CORPORATION DOES NOT HONOR VERBAL STATEMENTS CONCERNING THE WARRANTY.
The distributor and/or dealer are not sanctioned to create verbal warranties about the product described in this
agreement. Any statements will not be honored or be made part of the agreement of sale. This document is the final,
complete and exclusive terms of the agreement.
THIS WARRANTY IS EXCLUSIVE AND REPLACES ALL OTHER WARRANTIES.
Amvex Corporation shall not, under any circumstances, be liable for incidental or consequential damages including,
but not limited to, profit loss, loss of sales or injuries to person(s) or property. Correction of non-compliances as
noted above will result in completion of all liabilities of Amvex Corporation whether based on agreement, neglect or
otherwise. Amvex Corporation reserves the right to stop manufacturing any product or change materials, designs or
specifications without notice. All claims for warranty must first be approved by Amvex’s Repair Department:
([email protected] or 905-764-7736). A valid Return Goods Authorization (RGA) number must be obtained from
Amvex prior to commencement of any warranty claim.
Table of contents
Other Amvex Controllers manuals
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
