American Dynamics AD2032 User manual

2032

Alarm Responder

This manual describes the installation and operating procedures for the American Dynamics model 2032 Alarm Responder.

The 2032 Alarm Responder can be used with all American Dynamics Matrix Switching Systems to follow and respond to

alarm conditions. The 2032 Alarm Responder provides a relay closure when a monitor goes into an alarm condition. The

relay closures may be used to start a VCR or other such device. Other uses include the operation of panel displays showing

alarmed monitors.

Installation and Operating Instructions

The software/firmware furnished with this equipment is confidential to and is copyrighted by SENSORMATIC

ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of

SENSORMATIC. The software/firmware is furnished to the purchaser under a license for use on a single system.

Information furnished by SENSORMATIC is believed to be accurate and reliable. However, no responsibility is assumed by

SENSORMATIC for its use; nor for any infringements of other rights of third parties which may result from its use. No

license is granted by implications or otherwise under any patent or patent rights of SENSORMATIC.

The installation of this product should be made by qualified

service personnel and should conform to all local codes.

QA301D

WWAA

AARR

RRNN

NNIIIINN

NNGG

To reduce the risk of fire or shock hazard, do

not expose this product to rain or moisture.

AMERICAN

DYNAMICS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVERS (OR BACK) .

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION !

The lightning flash with arrowhead

symbol, within an equilateral

triangle, is intended to alert the

user to the presence of uninsulated

"dangerous voltage" within the

product's enclosure that may be of

sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an

equilateral triangle is intended to

alert the user to the presence of

important operating and maintenance

(servicing) instructions in the

literature accompanying the product.

UUNN

NNPP

PPAA

AACC

CCKK

KKIIIINN

NNGG

AANN

NNDD

IIIINN

NNSS

SSPP

PPEE

EECC

CCTT

TTIIIIOO

OONN

Unpack carefully. This is an electronic product and should

be handled as such. Compare the items received with the

packing list with your order.

Be sure to save:

1. The shipping cartons and insert pieces. They are the )

safest material in which to make future shipments of

the product.

2. The IMPORTANT SAFEGUARDS sheet.

3. These Installation and Operating Instructions.

MMAA

AAIIIINN

NNTT

TTEE

EENN

NNAA

AANN

NNCC

CCEE

User maintenance of this unit is limited to external cleaning

and inspection. For specific recommendations refer to the

IMPORTANT SAFEGUARDS sheet packaged with this product.

IIIINN

NNSS

SSTT

TTAA

AALL

LLLL

LLAA

AATT

TTIIIIOO

OONN

AANN

NNDD

SSEE

EERR

RRVV

VVIIIICC

CCEE

If you require information during installation of this

product or if service seems necessary, contact the

Sensormatic Repair and Service Department at (800)

442-2225. You must obtain a Return Authorization Number

and shipping instructions before returning any product for

service.

Do not attempt to service this product yourself. Opening or

removing covers may expose you to dangerous voltages or

other hazards. Refer all servicing to qualified personnel.

This equipment has been tested and

found to comply with Part 15 of the

FCC Rules.

Operation is subject to the

following two conditions: 1. This

device may not cause harmful

interference, and 2. This device

must accept any interference

received, including interference

that may cause undesired operation.

Table of Contents

Description............................................................ 1

Features ................................................................. 1

Installation............................................................ 2

Setup ..................................................................... 2

Monitor Select............................................ 2

Connections

Relay Connections..................................... 3

Data Line Connections............................... 3

Control Code Line Connections................. 4

Operation.............................................................. 5

Power Sources...................................................... 5

Powering Up......................................................... 5

Typical System Connections ....................Appendix

Specifications...........................................back page

DESCRIPTION

The 2032 Alarm Responder provides relay contact closures

which correspond to Matrix Switching System monitors that

are in an alarm condition. The Alarm Responder reads the

switching system's LAN/Data Line or Control Code interface

to determine which monitor is in alarm, then provides a

contact closure that corresponds to the monitor in alarm.

The 2032 receives data from either the LAN output of a 1995,

the DATA LINE output of a 1996, or the Control Code

output of other Matrix Switching Systems.

The 2032 filters the incoming codes for monitor commands to

identify alarm messages. When a monitor alarm is detected,

the corresponding 2032 relay contact is closed. After all

alarms have been cleared from a followed monitor, the

corresponding relay closure opens.

The Alarm Responder can follow a maximum of 128 system

monitors, in groups of 16. Note: Monitors 65-128 can be

followed only from 1995/1996 systems, on Data Line 2. The

2032 contains 32 addressable, normally open relays. The 32

relays can be grouped in series or in two groups of 16. Each

of the two groups can control 16 relays.

FEATURES

The 2032 Alarm Responder has the following features:

☛ SCREW TERMINAL WIRE CONNECTORS

☛

LED INDICATOR FOR “VALID" CODE

☛

LED POWER INDICATOR

☛

DIP SWITCH SELECTION FOR MONITOR GROUP

☛

COMPATIBLE WITH EITHER DATA LINE OR

CONTROL CODE

☛

UNIVERSAL MOUNT CABINET

DESCRIPTION

120V

60Hz

GROUP 1

GROUP 2

DATA LINE

OUT

DATA

PWR

ABCDEF

OFF

ABCDEF

OFF

ABCDEF

OFF

SELECT

ABCDEF

OFF

B W S

G1 IN G1 OUT G2 IN G2 OUT

Figure 1 - 2032 Alarm Responder Rear Panel

IF YOU ENCOUNTER ANY PROBLEMS

OPERATING THIS UNIT, OR NEED

TECHNICAL ASSISTANCE, CALL OUR

SERVICE CENTER AT:

within the United States: 1-800-442-2225

outside the United States: (845) 624-7600

INSTALLATION

This installation should be made by qualified service

personnel and should conform to all local codes. Safeguards

must be taken to avoid unintentional operation by employees

and maintenance personnel working about the premises, by

falling objects, by customers, by building vibration, and by

similar causes.

For optimum performance, the 2032 Alarm Responder should

be located near the Switching System Controller or near the

Data Line or Control Code Line of the Matrix Switching

System.

The cabinet of a 2032 may be surface or rack mounted in any

convenient location with adequate ventilation. Avoid heat

sources or poorly ventilated racks.

Rack Mounting

The 2032 is shipped with mounting ears flush with the front

panel, and can be mounted to the front of a standard 19-inch

rack. The mounting ears of the 2032 can also be placed such

that they are flush with the rear panel. This allows the 2032

to be mounted to the rear of a rack equipped with mounting

channels. For proper ventilation allow at least three feet (1m)

from the rear of the racks to any wall and one EIA rack height

(1 3/4 inches) between units in a rack.

Surface Mounting

The unit can also be surface mounted. Reinstall the mounting

ears such that they are perpendicular to the side of the unit.

The mounting ears may be positioned either flush with the

top or bottom covers of the unit or offset from the covers.

SETUP

Monitor Group Select

The relay closures on the 2032 are activated in response to a

Matrix Switching System monitor going into alarm. Two 8-

position DIP switches located on the rear panel of the 2032

are used to identify the monitors that the 2032 will respond

to. The DIP switches and associated relay group connectors

are shown in Figure 2.

The first DIP switch (1) sets the monitor group for the

GROUP 1 relays (relays 1 through 16). The third DIP switch

(3) sets the monitor group for the GROUP 2 relays (relays 17

through 32). The second and fourth DIP switches are not

used in the 2032. Switches 1 and 3 can be set either to the

same or to two different monitor groups.

For Control Code use, each control line contains information

for a maximum of eight monitors, thus the DIP switches are

not used and must be set to OFF.

For 1995/1996 systems, each Data Line contains information

for up to 64 switching system monitors. Data Line 1 is for

monitors 1-64 and Data Line 2 is for monitors 65-128. The

DIP switches must be set to identify the group of monitors

that the 2032 will respond to, for the Data Line connected to

the 2032. Table 1 below shows the DIP switch settings

applicable to both Data Lines.

Table 1 - DIP Switches 1 or 3, Monitor Group Select

0 = OFF, 1=ON

Monitor Group

Data Line 1 Data Line 2 A B C D E F

1-16 65-80 00000000

17-32 81-96 00000001

33-48 97-112 00000010

49-64 113-128 00000011

Figure 2 - Monitor Group Relays and Switches

INSTALLATION and SETUP

120V

60Hz

GROUP 1

GROUP 2

DATA LINE

OUT

DATA

PWR

ABCDEF

OFF

ABCDEF

OFF

ABCDEF

OFF

SELECT

ABCDEF

OFF

B W S

G1 IN G1 OUT G2 IN G2 OUT

DIP Switch 1 - Monitor Group Setting for Group 1 Relays (1 - 16)

DIP Switch 2 - Not Used

DIP Switch 3 - Monitor Group Setting for Group 2 Relays (17 - 32)

DIP Switch 4 - Not Used Group 1 Relays

Group 2 Relays

CONNECTIONS

Relay Connections

The 2032 Alarm Responder provides relay closures only;

they are not intended to supply power. Two groups (GROUP

1 and GROUP 2) of four 12-pin relay connectors are

provided on the rear panel (see Figure 2, page 2). Each group

provides connections for double pole relays. The two groups

provide 32 pairs of relay closures. Figure 3 illustrates the

internal 2032 relay interconnections for Group 1 relays.

The relay connections to the unit must be made with shielded,

2-wire twisted pair (22 AWG or heavier gauge wire or

equivalent). The shield wire is to be connected to the

grounding terminal.

Each set of three pin connections is labeled with a relay

number, from 1 through 32, corresponding to one of the

monitors of the monitor group(s) selected. Each pin within

one of the numbered sets is also labeled, under the connector,

with an A, a B, and a ground symbol. The A and B pins on

each connection are the contacts for one side of each double

pole relay. The contacts for the other side of each relay are

connected to the common Group connectors (next paragraph).

The ground pin is provided for shielding.

One 12-pin connector on the lower right of the 2032 rear

panel contains the common connections for each relay group.

Each set of pins is labeled with the group number G1 IN, G1

OUT, G2 IN, and G2 OUT, and each pin is labeled with an A,

B, and ground. The A and B pins are common contacts for

the other side of the double pole relays; G1 IN and OUT are

connected to relays 1-16 (see Figure 3), and G2 IN and OUT

are connected to relays 17-32. The Group IN connections are

used for determining the function of the associated relays,

such as providing a user-supplied voltage, a short to ground,

or a unique signal on relay activation. The Group IN pins can

also be used as inputs from cascading 2032 units. The Group

OUT connections are used to connect the associated relays to

a single responding device, such as a speaker or an indicator

light, or for cascading to additional 2032’s.

For ease of attaching to external equipment, each connector is

supplied with a mating screw terminal connector, shown in

Figure 4. Insert the signal and shield wires into the slots of

the mating connector and tighten the hold-down screws.

When all lines have been connected, insert the 12-pin

connectors into the rear panel mating terminals.

The relay contact ratings are 0.6 Amps at 24 VAC, or 2 Amps

at 30 VDC, resistive load. Power through the relays is not

supplied by the 2032.

Data Line Connections (1995 or 1996)

A DATA LINE is connected from the DATA LINE OUT

BNC on a Matrix Bay to the DATA LINE IN BNC on the

rear panel of the Alarm Responder. (Older 1995 systems

used the term LAN IN/OUT). Use a good grade RG-59 video

cable (Belden 8241 or equivalent). The DATA LINE OUT

BNC on the Alarm Responder must be fitted with a 75-ohm

BNC terminator, or if used to loop to other DATA LINE

controlled equipment, it must be terminated at the end of the

run.

The 2032 must be connected to the Data Line which is used

for the group of monitors to be followed. For 1995 and 1996

systems, Data Line 1 is for monitors 1-64 and Data Line 2 is

for monitors 65-128.

The LED labeled DATA, on the rear panel, will illuminate

when valid code is received on the Data Line.

CONNECTIONS

Figure 4 - Typical 12-Pin Connector

Figure 3 - 2032 Relay Contacts (Group 1)

HOLD DOWN SCREWS

INSERT CONNECTOR

THIS DIRECTION

G1 IN

G1 OUT

Control Code Line Connections

The 12-pin terminal connector located at the lower left side of

the rear panel is used for Control Code connections. The

connector is labeled B, W, and S. The B is for the BLACK

code wire, the W is for the WHITE code wire, and the S is for

the SHIELD wire.

The Control Code line connections to the 2032 Alarm

Responder must be shielded, 2-wire twisted pair (Belden

8760; for plenum use Belden 88760 or equivalent).

Code Lines are NEC Class 2, low voltage circuits. Where

local codes permit, installation in conduit is not required.

Avoid installation near high voltage or other potential

interference sources.

If the 2032 Alarm Responder is used with Control Code,

remove the top cover of the unit and locate the DIP switch on

the printed circuit board (see Figure 4, below). Set the eighth

switch position of this DIP switch to the ON position. This

setting enables the use of Control Code in the 2032.

Note: As shipped, the 2032 is set to operate in the Data Line

mode; this switch is set to the OFF position.

Control Code lines must be terminated in 120 ohms. Check

the last unit on each line to ensure that 120-ohm termination

is present. Intermediate units on a Control Code line must

not have 120-ohm termination. To remove the termination of

the 2032 code line, jumper J32 must be removed from the

main PCB. See Figure 4 for the location of this jumper.

Note: As shipped, the 2032 is set for 120-ohm termination;

this jumper is inserted.

Multiple 2032s may be connected in a "Star" configuration to

a Control Code distribution unit (1691 or 2091). See Figure

5. For this connection, each 2032 must have a 120-ohm

termination.

A maximum of three 2032s, or other Control Control devices,

may be “Daisy-chained” on a single code line. When devices

are “Daisy Chained”, intermediate devices must not contain a

120-ohm termination on the Control Code line. Only the last

unit in a "Daisy Chain" has a 120-ohm terminator. See

Figure 6 for “Daisy Chain” connections.

In switching systems using Control Code, the 2032 Alarm

Responder must be connected to the code line which contains

the monitors to be followed.

For 1650A operation, four separate control lines could be in

use. The first control line is for monitors 1-8 and cameras 1-

64. The second control line is for monitors 1-8 and cameras

65-128. The third control line is for monitors 9-16 and

cameras 1-64. The fourth control line is for monitors 9-16

and cameras 65-128. Separate 2032 Alarm Responders may

be required for following monitors on separate control lines.

See the Appendix for illustration of a typical connection to

multiple 1650A control lines.

CONNECTIONS

Dip Switch

Power Cord

OFF

12345678

J32

120 ohm Termination Jumper

CODE

DISTRIBUTOR

2 0 3 2

B W S

2 0 3 2

B W S

2 0 3 2

B W S

T = 120 OHM TERMINATION

OTHER CODE

LINES

Figure 5 - Code "Star" Configuration"

Figure 4 - DIP Switch Location on PCB

CODE

DISTRIBUTOR

2 0 3 2

B W S

2 0 3 2

B W S

2 0 3 2

B W S

T = 120 OHM TERMINATION

OTHER CODE

LINES

Figure 6 - Code "Daisy Chain" Configuration

CAUTION - Due to the presence of non-

insulated components with hazardous voltages,

the following internal adjustments should be

performed by qualified service personnel only.

Other manuals for AD2032

This manual suits for next models

Table of contents

Other American Dynamics Security System manuals

American Dynamics

American Dynamics Intellex Ultra User manual

American Dynamics

American Dynamics AD2052 User guide

American Dynamics

American Dynamics DigiMux DG4004 User manual

American Dynamics

American Dynamics Intellex DV16000 Installation and operation manual

American Dynamics

American Dynamics Intellex DV16000 Installation and operating instructions

American Dynamics

American Dynamics Intellex Ultra User manual

American Dynamics

American Dynamics RABW4QUAD Assembly instructions

American Dynamics

American Dynamics MegaPower 3200 Manual

American Dynamics

American Dynamics MegaPower 3200 User manual

American Dynamics

American Dynamics AD2096A User manual

American Dynamics

American Dynamics AD2032 User manual

American Dynamics

American Dynamics VideoEdge Guide

American Dynamics

American Dynamics Intellex DV8000 User manual

American Dynamics

American Dynamics Intellex DV16000 User manual

American Dynamics

American Dynamics MegaPower 3200 Service manual

American Dynamics

American Dynamics Intellex Digital Recorder User manual

American Dynamics

American Dynamics AD1273 CobraDome User manual

American Dynamics

American Dynamics AD2010N Manual

American Dynamics

American Dynamics Intellex 2.0 Installation and operation manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual