American Dynamics ADC 660P User manual















Hi-Res. B/W camera

instruction manual

ADC 660N

ADC 660P

Version: Rev. A

Part Number 8200-0839-01

Notice

To prevent fire or shock hazard, do not expose the unit to rain or

moisture.

The symbol is intended to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature accompanying the unit.

The symbol is intended to alert the user to the presence of uninsulated

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

Warning

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference, in which case the user will be

required to correct the interference at his own expense.

Equipment Modification Caution

Equipment changes or modifications not expressly approved by Sensormatic Electronics

Corporation, the party responsible for FCC compliance, could void the user’s authority to

operate the equipment and could create a hazardous condition.

This class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

WARNING

Caution

This installation should be made by a qualified service person and should conform to all

local and national electrical and mechanical codes.

PRECAUTIONS

1. Do not attempt to disassemble the camera.

In order to prevent electric shock, do not remove screws or cover. There are

no user-serviceable parts inside.

2. Do not expose the camera to rain or moisture, or try to operate it in wet

areas.

Take immediate action if the camera becomes wet. Turn the power off and refer

servicing to qualified service personnel. Moisture can damage the camera and

also create a danger of electric shock.

3. Do not use strong or abrasive detergents when cleaning the camera body.

Use a dry cloth to clean the camera when dirty. In a case where the dirt is

hard to remove, use a mild detergent and wipe gently.

4. Never point the camera toward the sun.

Whether the camera is used outdoors or not, never point it toward the sun.

Use caution when operating the camera in the vicinity of spot lights or other

bright lights and light reflecting objects.

5. Do not operate the camera beyond its temperature, humidity or power source

ratings.

Do not use the camera in an extreme environment where high temperature or

high humidity exists. Use the camera under conditions where temperatures are

between 14° F~122° F (-10° C~+50° C) and humidity is below 85%.

6. Use a 24V AC / 12V DC class 2 LPS supply only.

Hi-Res. B/W camera instruction manual

ADC 660N and ADC 660P

_________________________________

Product specifications subject to change without notice. Certain product names

mentioned herein may be trade names and/or registered trademarks of other

companies.

Customer Service

Thank you for using American Dynamics products. We support our products through

an extensive worldwide network of dealers. The dealer through whom you originally

purchased this product is your point of contact if you need service or support. Our

dealers are empowered to provide the very best in customer service and support.

Dealers should contact American Dynamics at (800) 507-6268 or (561) 912-6259 or

on the Web at www.americandynamics.net.

Hi-Res. B/W camera instruction manual

ADC 660N and ADC 660P

_________________________________

I. CONNECTORS AND CONTROLS .................................................................................. 7

1. VIDEO OUTPUT CONNECTOR (BNC)................................................................................ 7

2. POWER INPUT CONNECTOR (SCREW TERMINAL) ............................................................... 7

3. AUTO IRIS LENS CONNECTOR FOR VIDEO DRIVE LENS .................................................... 8

4. AUTO IRIS LENS CONNECTOR FOR DC DRIVE LENS .......................................................... 8

5. BLC (BACKLIGHT COMPENSATION) ON/OFF SWITCH ...................................................... 9

6. ALC/ELC SELECT SWITCH (EE/ELC IS ON; ALC/AI IS OFF) ....................................... 10

7. AGC ON/OFF SWITCH ............................................................................................... 11

8. INT/LL SWITCH (LL IS ON; INT IS OFF) ...................................................................... 11

9. FL ON SWITCH (FLICKERLESS ON/OFF)...................................................................... 11

10. V-PHASE ADJUSTMENT POTENTIOMETER....................................................................... 11

11. ALC LEVEL ADJUSTMENT POTENTIOMETER FOR DC DRIVE LENS.................................... 13

12. POWER INDICATOR LED ............................................................................................... 14

13. BACKFOCUS ADJUSTMENT SCREW ................................................................................ 14

14. C MOUNT ADAPTOR RING ............................................................................................ 16

15. CCD DUST PROTECTIVE CAP ....................................................................................... 16

16. CAMERA MOUNT HOLE ................................................................................................. 16

17. CAMERA MOUNT BASE ................................................................................................. 16

II. EXAMPLES OF CONNECTIONS .................................................................................. 17

1. SIMPLEST:ONE MONITOR SYSTEM WITH ONE CAMERA ..................................................... 17

2. ONE MONITOR SYSTEM WITH TWO OR MORE CAMERAS..................................................... 17

III. DIMENSIONS................................................................................................................. 18

IV. SPECIFICATIONS ......................................................................................................... 19

Hi-Res. B/W camera instruction manual

ADC 660N and ADC 660P

_________________________________

I. CONNECTORS AND CONTROLS

1. Video Output Connector (BNC)

1.0V p-p/75Ω composite video signal is provided at this connector.

2. Power Input Connector (screw terminal)

Hi-Res. B/W camera instruction manual

ADC 660N and ADC 660P

_________________________________

This terminal accepts 12 VDC or 24 VAC.

Power Requirement: Maximum 200 mA (12 VDC), Maximum 100 mA (24 VAC).

Recommended Power Supply: Minimum 500 mA (12 VDC); Minimum 300 mA (24 VAC).

Caution:

Use a 24V AC / 12V DC class 2 LPS supply only.

3. Auto Iris Lens Connector for VIDEO Drive Lens

This connector supplies 9 VDC power and video signal, without sync, for video-drive

type Auto Iris lens.

When using a VIDEO drive lens, the ALC/ELC DIP #1 must be set to the ALC (OFF)

position.

4. Auto Iris Lens Connector for DC Drive Lens

This connector supplies the control signals to the DC drive Auto Iris lens.

PIN Signal

GROUND

POWER SUPPLY (9 VDC, 40mA)

VIDEO OUTPUT (0.7Vp-p without sync)

Hi-Res. B/W camera instruction manual

ADC 660N and ADC 660P

_________________________________

When using a DC drive lens, the ALC/ELC DIP #1 must be set to the ALC (OFF)

position.

5. BLC (Backlight Compensation) ON/OFF Switch

If the subject you wish to view is too dim because of a bright background, set the

BLC DIP switch #2 to ON to compensate for the bright background.

With BLC on, the background brightness may saturate in some cases. This

function may not operate properly if the object is too small compared to the area

of the background. This function can be used with either the linear shutter (EE or

ELC mode) or an Auto Iris lens (AI lens or ALC mode).

WITH BLC OFF WITH BLC ON

Hi-Res. B/W camera instruction manual

ADC 660N and ADC 660P

_________________________________

6. ALC/ELC Select Switch (EE/ELC is ON; ALC/AI is OFF)

This switch is used to select EE (electronic exposure)/ELC (electronic light control)

mode or AI (Auto Iris lens)/ALC (automatic light control) mode. DIP switch 1 is set

to ON for EE/ELC and OFF for AI/ALC.

In the EE/ELC mode, a continuously variable electronic shutter is employed to

automatically control the exposure time of the CCD image sensor according to the

incoming light level. With this mode selected, a fixed or manual iris lens can be

used instead of an Auto Iris lens. In the AI/ALC mode, the CCD shutter speed is

fixed to 1/60 (1/50) sec, and the incoming light level is controlled by the Auto Iris

lens. To use a video-drive type or the DC-drive type of Auto Iris lens, set this

switch to the ALC position.

Cautions

 Under bright lighting conditions such as outdoors, use an Auto Iris lens

because the EE/ELC control range is not wide enough under these

conditions.

 Under certain unique lighting conditions, the following phenomena may

appear:

 Strong smear and/or blooming on highlighted objects such as spotlights

or windows.

 Noticeable flicker in the picture and/or color rendition variations. To

avoid this, use an Auto Iris lens.

 When operating in EE/ELC mode with manual iris lens, the depth of field of

the image may be less than that obtained by using an AI/ALC lens. Depth

of field varies inversely with the iris opening. Thus, using this camera in

EE/ELC mode with the manual iris lens fully opened may result in less depth

of field and the distant objects in a picture may be seen out of focus.

 Fixed iris or manual iris lenses may be used with the linear shutter (EE/ELC

mode) where the scene brightness varies over a limited range.

 Do not use the EE/ELC mode when an Auto Iris lens is installed.

This manual suits for next models

Table of contents

Other American Dynamics Security Camera manuals

American Dynamics

American Dynamics ADCA330 User manual

American Dynamics

American Dynamics RASOPPC-1 User manual

American Dynamics

American Dynamics SpeedDome Ultra III Installation and maintenance instructions

American Dynamics

American Dynamics illustra 400 User manual

American Dynamics

American Dynamics SpeedDome Ultra VIIE Installation and maintenance instructions

American Dynamics

American Dynamics ADC520D User manual

American Dynamics

American Dynamics ADCA330CN User manual

American Dynamics

American Dynamics IP speedDome Ultra 8 Installation and maintenance instructions

American Dynamics

American Dynamics ADCIPE3312ISN User manual

American Dynamics

American Dynamics ADC780 Assembly instructions

American Dynamics

American Dynamics ADC521B User manual

American Dynamics

American Dynamics ADC520D User manual

American Dynamics

American Dynamics ADC722WP User manual

American Dynamics

American Dynamics Illustra Flex Series ADCi600F-W012** User manual

American Dynamics

American Dynamics ADSDUHOC User manual

American Dynamics

American Dynamics Tyco ADC770 User manual

American Dynamics

American Dynamics ADC500 User manual

American Dynamics

American Dynamics ADCTDN0230P User manual

American Dynamics

American Dynamics Illustra Flex Series User manual

American Dynamics

American Dynamics SpeedDome Ultra VI Installation and maintenance instructions

American Dynamics

American Dynamics SpeedDome Ultra Manual

American Dynamics

American Dynamics Illustra 1MP User manual

American Dynamics

American Dynamics SpeedDome Optima LT Manual

American Dynamics

American Dynamics ADC710 User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications