American Dynamics AD615 User manual
DeltaDome™ Programmable Surveillance Camera
Configuration Utility Quick Reference Guide
8000-2613-02, Rev. B Quick Reference Guide
This Quick Reference Guide illustrates the screens found in the
DeltaDome Programmable Surveillance Camera Configuration
Utility. The large numbers in the circles represent the number of
the screen. The small numbers appearing to the right of the menu
choices represent the screen you will see if you pick that choice.
Note: The numbers in the circles do not actually appear on the
screens.
To start the configuration utility, do one of the following:
•For SensorNet or RS-422, press and hold Iris Open, press and
hold a Focus button, then press Zoom Out.
•For Manchester, turn the key switch to Prog (or disable the
system lock on the TOUCH TRACKER®), use the keypad to enter
66, then press Set Preset..
Refer to the keyboard or TOUCH TRACKER operating instructions
for the locations of the control buttons.
DOME CONFIGURATION MENU
PAN/TILT/ZOOM OPTIONS
CAMERA / LENS FUNCTIONS
ALARMS / AREAS / HOME
ON-SCREEN TEXT DISPLAY
LANGUAGE / PASSWORD
EXIT AND SAVE CHANGES
QUIT WITHOUT SAVING
RESET TO FACTORY SETTINGS
1
2
3
4
5
6
NOTE: If password protection is enabled, you must enter the
password before the Dome Configuration Menu will display.
Refer to screen 19 for information.
The following table describes the functions of the controls used
to interact with the screens. Where a specific Focus button is not
specified, either the Focus Near or Focus Far button may be used.
Function Control
Display configuration menu (SensorNet and RS-422
only) Iris Open, Focus,
then Zoom Out
Display configuration menu (Manchester only) Key switch to Prog,
66, then Set Preset
Save and exit utility from any screen (not supported
on Manchester) Iris Close then
Focus
Moves highlight bar up Tilt Up
Moves highlight bar down Tilt Down
Moves highlight bar right Pan Right
Moves highlight bar left Pan Left
Selects the highlighted item Focus Far
Increases the value or displays the next choice
During naming, moves the cursor to the right of the
current character in the name
Zoom In
(Zoom Tele)
Decreases the value or displays the previous choice
During naming, moves the cursor to the left of the
current character in the name
Zoom Out
(Zoom Wide)
PAN / TILT / ZOOM OPTIONS
PROPORTIONAL FLIP OFF
1ST ZOOM STOP X 24
MAX TOTAL ZOOM X 128
EXIT
RESET TO FACTORY SETTINGS
2
1
Settings (Defaults in Bold)
Proportional Flip ON / OFF
1st Zoom Stop X 16 / 24
Max Total Zoom X 32 / 48 / 64 / 80 / 96 / 112 / 128
CAMERA / LENS FUNCTIONS
LINE LOCK OFF
AGC MODE ON
AGC GAIN 112
EXIT
RESET TO FACTORY SETTINGS
AUTO WHITE BAL ON
RED WHITE BAL 457
BLUE WHITE BAL 563
3
1
Settings (Defaults in Bold)
Line Lock ON / OFF
AGC Mode ON / OFF
AGC Manual Gain: 0 - 1128*
Auto White Bal ON/OFF
Red White Bal 128-1023**
Blue White Bal 128-1023**
* AGC Mode must be OFF to change
** Auto White Bal must be OFF to change
2 8000-2613-02, Rev. B Quick Reference Guide
ALARMS / AREAS / HOME
SET ALARM ACTIONS
CONFIGURE NORMAL STATES
CONFIGURE HOME POSITION
EXIT
PROGRAM AREA BOUNDARIES
PROGRAM PRESETS
4
1
7
8
9
10
11
Select an item, then press Focus Far to make the changes.
Alarm inputs and outputs are not supported for Manchester.
ON-SCREEN TEXT DISPLAY
STATUS DISPLAY OFF
EXIT
DISABLE ALL NAMES? NO
NAME CONFIGURATION MENU
TEXT ATTRIBUTE OPTIONS
DIAGNOSTICS DISPLAY ON
5
1
13
16
Settings (Defaults in Bold)
Status Display ON / OFF
Disable All Names? YES / NO
Diagnostic Display ON / OFF
LANGUAGE / PASSWORD
LANGUAGE SELECTION
EXIT
SET PASSWORD
PASSWORD PROTECTION OFF
6
1
17
18
Press Focus Far to display Language Selection (screen 17) or Set
Password (screen 18).
Settings (Defaults in Bold)
Password Protection ON / OFF
SET ALARM ACTIONS
EXIT
INPUT NO. ACTION
SEND INPUTS TO HOST? YES
NO ACTION
1PRESET 96
2PATTERN 33NO ACTION4
INTERNAL ALARMS
7
4
Settings (Defaults in Bold)
Input 1 - 4 Actions NO ACTION / PRESET / PATTERN
Send Inputs to Host? YES / NO
Preset Number 1-96; Pattern Number 1-3
Note: Do not assign input action on both dome and controller.
8000-2613-02, Rev. B 3
CONFIGURE NORMAL STATES
EXIT
INPUT NO. NORMAL STATE
OPEN1OPEN
2CLOSED3OPEN4
8
4
Settings (Defaults in Bold)
Input 1 - 4 Normal State OPEN / CLOSED
Note: Do not assign input action on both dome and controller.
CONFIGURE HOME POSITION
EXIT
HOME POSITION PRESET 96
10
RETURN TIME MINS
9
4
Settings (Defaults in Bold)
Return to Home Position NO ACTION / PRESET/ PATTERN
Return Time Mins 1 - 60 (Default is 10 minutes)
Preset Number 1-96; Pattern Number 1-3
PROGRAM AREA BOUNDARIES
ZOOM to mark BOUNDARY
PAN to start of BOUND 3
PAN RIGHT ONLY
FOCUS saves and exits
10
•Up to 16 areas can be programmed.
•Press Zoom In or Zoom Out to set area boundary
•Press Focus Far when finished setting areas
SELECT PRESET TO PROGRAM
EXIT
PRESET NAME
PRESET
NUMBER
PRESET 9696
FOCUS FAR to program preset
11
4
12
•Use Zoom In or Zoom Out choose the correct preset number.
•Press Focus Far to perform preset programming.
12 PROGRAM PRESET
PRESET 1
EXIT
Position camera with PAN,
TILT, ZOOM, and IRIS
FOCUS FAR to save and exit
This screen appears under two circumstances:
•By selecting a preset number and pressing Focus Far on the Select
Preset To Program screen (see screen 11).
•By selecting a preset that has not been programmed as the Home
Position (see screen 9).
Use Pan, Tilt, Zoom, and Iris controls to set the view for the preset.
Press Focus Far when finished.
Press Focus Far
twice to return to
screen 4.
If Preset is selected and
no preset exists, you will
see screen 12.
11 or 4
4 8000-2613-02, Rev. B Quick Reference Guide
NAME CONFIGURATION MENU
OFF
CAMERA NAME OFFAREA NAME OFFPRESET NAME OFFPATTERN NAME ON
ALARM NAME
FOCUS FAR to program name
13
EXIT 5
15
14
RESET PROGRAMMABLE NAMES
Settings (Defaults in Bold)
Camera Name ON / OFF
Area Name ON / OFF
Preset Name ON / OFF
Pattern Name ON / OFF
Alarm Name ON / OFF
•Use Zoom In or Zoom Out to change setting for highlighted item.
•Press Focus Far to perform name programming for highlighted item.
In this example, Camera Naming would be started.
SELECT NAME TO PROGRAM
EXIT
CURRENT NAME
PATTERN
NUMBER
FOCUS FAR to program names
14
13
15
PATTERN 11
Example Select Name to Program Screen (for Patterns)
•Use Zoom In or Zoom Out choose the correct area, preset, pattern or
alarm number.
•Dome moves to start of specified area, preset, or pattern (if
programmed)
•Press Focus Far to display Name Programming Screen
Available Settings:
Area Number 1-16
Preset Number 1-96
Pattern Number 1-3
Alarm Number: 1-4
NAME PROGRAMMING
PATTERN 1
NAME: PATTERN 1. . . . . . . . . .
EXIT
UNDO CHANGES AND QUIT
15
A B C D E F G H I J K L M N O P Q R S T
U V W X Y Z a b c d e f g h i j k l m n
o p q r s t u v w x y z 0 1 2 3 4 5 6
7 8 9 / -
Example Name Programming Screen (for Patterns)
•Names can have up to 19 characters
•Use Zoom In to move cursor one space to right in Name
•Use Zoom Out to move cursor one space to left in Name
•Use Pan and Tilt to move highlight around character field
•Press Focus Far to accept highlighted character
•The SPACE character is located between zand 0 (zero)
TEXT ATTRIBUTE OPTIONS
CHARACTER OUTLINE OFF
EXIT
TRANSLUCENT NAMES OFF
16
5
Settings (Defaults in Bold)
Character Outline ON / OFF
Translucent Names ON / OFF
13 or 14
13 or 14
Blank
Space
8000-2613-02, Rev. B 5
LANGUAGE SELECTION
ENGLISH
SPANISH
FRENCH
GERMAN
ITALIAN
PORTUGUESE
EXIT
17
6
20
•Default setting is English.
•Characters ãand õare not available in Portuguese.
SET PASSWORD
PASSWORD: * *
CONTINUE
CANCEL 6
18
A B C D E F G H I J K L M N O P Q R S T
U V W X Y Z a b c d e f g h i j k l m n
o p q r s t u v w x y z 0 1 2 3 4 5 6
7 8 9 / -
•Passwords can be from 1 to 8 characters.
•Asterisks appear when characters are selected.
•Use Zoom In to move cursor one space to right in Password
•Use Zoom Out to move cursor one space to left in Password
•Use Pan and Tilt to move highlight around character field
•Press Focus Far to accept highlighted character
•The SPACE character is located between the zand 0(zero).
•To accept password, move highlight to Continue, then press Focus
Far. Re-enter for Verification appears on screen.
•To cancel password programming, move highlight to Cancel, then
press Focus Far.
•To set or change password, the same password must be entered twice.
After 2nd successful entry, screen 6 appears
•Password Protection must be set to ON for password to be
activated. See screen 6.
ENTER PASSWORD
PASSWORD: * *
CONTINUE
CANCEL
19
A B C D E F G H I J K L M N O P Q R S T
U V W X Y Z a b c d e f g h i j k l m n
o p q r s t u v w x y z 0 1 2 3 4 5 6
7 8 9 / -
•Passwords can be from 1 to 8 characters.
•Asterisks appear when characters are selected.
•Use Zoom In to move cursor one space to right in Password
•Use Zoom Out to move cursor one space to left in Password
•Use Pan and Tilt to move highlight around character field
•Press Focus Far to accept highlighted character
•The SPACE character is located between the zand 0(zero).
•To accept password, move highlight to Continue, then press Focus
Far. If password is correct, screen 1appears. Otherwise, Enter
Password screen remains.
•To cancel password entry, move highlight to Cancel , then press
Focus Far. The dome resumes normal operating mode.
SELECT CONTINUE TO RESET
CONTINUE
CANCEL
DOME MUST RESET TO
CHANGE LANGUAGE
20
17
•Dome must reset for language change to occur. With highlight bar on
Continue, press Focus Far to continue with language change.
•To cancel language change, use the Tilt control to move highlight bar
to Cancel. The Language Selection screen (screen 18) displays.
AD, American Dynamics, DeltaDome, and the AD logo are trademarks
of Sensormatic Electronics Corporation. Other product names (if any)
mentioned herein may be trademarks or registered trademarks of other
companies.
No part of this guide may be reproduced in any form without written
permission from Sensormatic Electronics Corporation.
© Copyright 1998. All rights reserved. BSL 9/98
1 or 19
Blank
Space
Reset Dome
Blank
Space
18 or 6
Other manuals for AD615
2
This manual suits for next models
1
Table of contents
Other American Dynamics Security Camera manuals
American Dynamics
American Dynamics ADCIPE3312ISN User manual
American Dynamics
American Dynamics AD715LS Series Owner's manual
American Dynamics
American Dynamics SpeedDome Ultra Manual
American Dynamics
American Dynamics SpeedDome Ultra VIIE Installation and maintenance instructions
American Dynamics
American Dynamics ADCA7BWO7RP User manual
American Dynamics
American Dynamics AD715LS Series Installation and maintenance instructions
American Dynamics
American Dynamics ADCPBW User manual
American Dynamics
American Dynamics ADCDW Series User manual
American Dynamics
American Dynamics ADC660 User manual
American Dynamics
American Dynamics RASO series User manual
American Dynamics
American Dynamics SpeedDome Optima LT Manual
American Dynamics
American Dynamics ADC531 User manual
American Dynamics
American Dynamics IP speedDome Ultra 8 User manual
American Dynamics
American Dynamics Discover 600 Series User manual
American Dynamics
American Dynamics Illustra Flex Series User manual
American Dynamics
American Dynamics Tyco Discover Series User manual
American Dynamics
American Dynamics IP speedDome Ultra 8 Manual
American Dynamics
American Dynamics SpeedDome Ultra Drone III User manual
American Dynamics
American Dynamics Illustra Flex Series User manual
American Dynamics
American Dynamics SpeedDome Ultra Drone II User manual
