Alen C360 User manual
MOBILE AIR CONDITIONER
USER’S MANUAL
Read Rules for Safe Operation and Instructions Carefully
2
CONTENTS
1. SAFETY RULES …………………………………………………………...2
2. NAME OF PARTS ………………………………………………………...3
3. ACCESSORIES …………………………………………………………….3
4. OPERATION PANEL OF THE AIR CONDITIONER ……………..…… 4-5
5. OPERATION AND INDICATION SECTIONS OF REMOTE
CONTROLLER ……………………………………………….………..6-7
6. OPERATION METHOD………………………………………….…..… 8-10
7. KEY-OPERATING INSTRUCTION FOR THE AIR
CONDITIONER..…………………………………………………..…. 11-13
8. INSTALLATION ..………………………………………………......… 13-15
9. MAINTENANCE …………………………………………………………15
10.TROUBLE SHOOTING ..…………………………………………………16
3
SAFETY RULES
1. Do not connect unit to any AC socket in disrepair.
2. Do not use in the following locations:
A: Next to source of fire
B: An area where oil is likely to splash.
C: An area exposed to direct sunlight.
D: An area where water is likely to splash.
E: Near a bath, a shower or a swimming pool.
3. Never insert your fingers or any foreign objects into the air outlet. Take special care to warn children of these
dangers.
4. Always store the unit upright in order to maintain the compressor in a proper condition.
5. Be sure to unplug the unit before cleaning.
6. The heater must not be located immediately below a socket outlet.
7. If the appliance is covered, there is a risk of overheating.
8. If the plug or electrical cord is damaged, it must be replaced by a repair shop appointed by the manufacturer,
because special purpose tools are required.
NOTE: The air-conditioner can be connected only a supply system impedance of no more than 0.4582 ohm. If
unsure, please consult your supply authority for system impedance information.
4
NAME OF PARTS
AIR INLET
REAR COVER
REMOTE
CONTROLLER
FRONT VIEW
CASTER
AIR OUTLET
OPERATION
PANEL
REAR VIEW
SIDE VIEW
POWER CORD
WATER PUMP
DRAIN HOSE
FRONT COVER
AIR INLET
CONTINUOUS
DRAIN HOSE
AIR OUTLET
AIR INLET
Fig.1
ACCESSORIES
1
QUANTITY
1
DUCT ASSEMBLY
PARTS NAME
WATER PUMP DRAIN HOSE
INSTALLTION PLATE
PARTS
Fig.2
Check all the accessories are included in the package and please refer to the installation instructions for their
usage.
5
OPERATION PANEL OF THE AIR CONDITIONER
i. Amodel display indicators (with electricity heating):
Set e
e
light
ly
Fig.3
ii. A model display indicators (only cooling):
light
Set
Fig.4
6
●B model display indicators :
Receiver
F
Fig.5
DISPLAY:
Auto mode indicate
Cooling mode indicate
Fan speed Heating mode indicate
mode indicate
Timer indicate Digital display
Swing indicate
Locked indicate
F
Fig.6
Note: 1.The AutoCoolingHeatingDry mode indicators will not display in the Fan mode.
2.The relevant display light according the set content by remote controller.
3.Air conditioner does not operate normally when set temperature indicator displaies unnormally, please
contact with the distributor for service.
<<Could you remove #2, #3 above? I do not understand what they mean.>>
7
OPERATION OF THE REMOTE CONTROL
Remarks: Tem
p
erature can be set between60~89.
Display Screen
For settin
g
dis
p
la
y
Sleep Button
For setting sleep
function.
Time setting Button
Press this button to
set timer or the clock
time.
Hour Button
Press this button to
change hour setting.
Reset Button
Reset remote control to
the original status.
ON/OFF Button
Press this button to start /
stop air conditioner.
Minute Button
Press this button to change
the minute setting.
Airflow sweep Button
For changing louver
position.
Timer selection Button
Selecting procedures:
On timer →Off timer→
Program control →Timer
cancelled →On timer
AUH Button
To change the condition of starting
auxiliary electric heater when air
conditioner in HEAT mode.
Mode selection Button
For selecting
AUTO HEAT
COOL DRY
SWEEP
Fan speed button
For selecting indoor fan
speed:
Auto Medium
High Low
AUT
Temp Adjustment Buttons
Press “▼” to decrease temp.
Press “▲” to increase temp.
MODE
SLEEP ON/OFF
TEMPERATURE
FAN SPEED
AUH FAN SWEEP
TIME TIME
R
HOUR MINUTE
RESET
AUT
O
SET TEMP PROGRAM
8
Remote Controller Display
Instructions for the remote controller
zThe remote controller uses two AAA alkaline battrries. Under normal condition, the batteries last for
about 6 months. Please use two new batteries of similar type (pay attention to the poles in installing).
After replacing the batteries, please use a point object (such as pen tip) to press “Reset” button.
zThe effective control distance of the remote controller is about 8 yards.
zWhen using the remote controller, please point the signal emitter towards the air conditioner receiver;
There should be no obstacles between the remote controller and the air conditioner.
zDo no press two buttons simultaneously on the remote control.
zDo not use wireless equipment (such as mobile phone) near the air conditioner. If interference occurs
because of this, please switch off the air conditioner, pull out power plug, then plug again and switch
on after a while.
zIf direct sunlight is hitting the the receiver on the air conditioner it may not be able to receive the signal
from the remote controller.
zTake care not to drop theh remote control and keep from direct sunlight or heat sources.
zKeep the remote control dry, if it gets wet use a soft, dry cloth for cleaning.
zThe batteries must be removed from the remote control before it is scrapped and disposed of safely.
Sleep Mode Display
Displayed when Pressing “SLEEP”
button the unit will enter into sleeping
operation.
Air refresh Display
(Not available)
AUH Display
It appears when
p
ressing the AUH
key is add in HEAT
mode.
Signal Emission
Symbol
It appears when
control signal is
emitted.
Display
displayed when
temp is displayed.
Time Display
Displays the time of
clock or timing
ON/OFF.
AUT SET TEMP PROGRAM
Wind Speed Selection
Display
High speed
Medium speed
Auto
Low speed
AUT
Operating Mode Selection
Display Timer setting
Display
PROGRAM
ON timer
OFF time
r
Program
Timer canceled
AUTO
COOL DRY
HEAT
FAN
9
OPERATION METHOD
AUTO, HEAT, COOL,FAN and DRY operation
Remarks:
1.When “AUTO” mode is set, the air conditioner will adjust the fan speed and select the COOL or DRY
mode according to the indoor temperature.
2.When “AUTO” mode is set, SLEEP and AUH functions are not available.
3.When “DRY” mode is set, in accordance with the D-value between indoor temperature and set
temperature, the air conditioner will start or stop the cooling operation and fan speed automatically to
decrease room humidity. The fan speed may change to maintain the humidity.
4.When “FAN” mode is set, temperature can’ t be adjusted. Step 2 of Operating precudures is not effective.
Only high, medium and low fan speed can be set; no Auto fan speed.
5.In the cooling-only model,the “AUH” function is not available and there is no AUTO-HEAT mode.
MODE
SLEEP ON/OFF
TEMPERATURE
FAN SPEED
AUH FAN SWEEP
AUT
O
SET TEMP
Switch On
Press ON/OFF button to start ai
r
conditioner. 3
Switch Off
Press ON/OFF
b
utton to stop ai
r
conditioner. 6
Temp Adjustment Buttons
Press “ ▲” “ ▼” buttons to set
temp as needed. 2
Setting Operation Mode
Auto Heat Sweep
Cool Dry 1
Airflow selection
Press “FAN SWEEP” button to select
airflow direction. 4
5
Setting Fan Speed
Four speeds can be selected:
Auto High
Medium Low
AUT
10
Clock Setting
On Timer
Note:
1. When on timer function is set, air conditioner will be turned off immediately. It will be turned on at the set
time; symbol “ ON ” will be deleted. If the set time is as same to the current time, air conditioner will be
turned on at this time of next day.
2. Press “ON/OFF” to cancel “On Timer” function, air conditioner will be turned on immediately.
Press “TIME” button to
select , clock display
will flash.
1
Press “HOUR” button to
change the hour display,
each press of HOU
R
button will increase o
r
decrease the time display
b
y 1 hour; hour displa
y
will be change
d
continuously when
pressing it continuously.
2
Press “MINUTE” butto
n
to change the minute
display, (the method as
step 2). The cloc
k
display will flash for 10
seconds after setting, the
remote controlle
r
displays current time.
3
MODE
SLEEP ON/OFF
TEMPERATURE
FAN SPEED
AUH FAN SWEEP
TIME TIME
R
HOU
R
MINUTE
RESET
SET TEMP
Set the clock time as
Clock Setting,
Press “TIME” button to
select ON , clock
display will flash.
1
Press “HOUR” o
r
“MINUTE” button; se
t
the time to turn on the
air conditioner on timer.
At this time if user press
“MINUTE” button, i
t
will increase o
r
decrease by 10 minutes.
2 Press “TIMER”
button to select
ON .3
MODE
SLEEP ON/OFF
TEMPERATURE
FAN SPEED
AUH FAN SWEEP
TIME TIME
R
HOU
R
MINUTE
RESET
SET TEMP
This manual suits for next models
1
Table of contents
Other Alen Air Conditioner manuals
Popular Air Conditioner manuals by other brands
Fujitsu
Fujitsu Inverter ASBA30JFC operating manual
Toshiba
Toshiba RAS-M10SMUV-E installation manual
Daikin
Daikin FXLQ20MAVE Operation manual
Hitachi
Hitachi RAS-E24CAK instruction manual
CIAT
CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance
Bestron
Bestron AAC6000 instruction manual
