AeroPlus Extra 330LT User manual
www.aeroplusrc.com [email protected]om
AeroPlus RC Copyright 2014 © All Rights Reserved
Extra 330LT
85-125CC
Item No：A-G120001
Specs：
WING SPAN: 111” (2833mm)
LENGTH: 100" (2530mm)
WING AREA: 2139sq in (138sq dm)
FLYING WEIGHT: 25.3-28lbs (11500-12800g)
ENGINE: 100cc-120cc gas
RADIO: 4CH/6-9S
Description
Covering Material Genuine Oracover
Carbon Fibre: Spinner, wing tube and sleeves, landing gear, tail gear;
Fibreglass servo arms, horn and reinforced U/C mounting
Fiberglass servo arms and horn;
Built-in tuned pipe or canister tunnel;
Removable Wings, Stabs and Rudders;
Carbon fibre rods to make the wings and fuselage light weight and strong;
Alu hub Wheels; Adjustable pushrods;
Two piece clamshell cowl, Ringed Cowl
Extra covering provided for small repairs
Pre drilled hinges
2 Colour schemes
H-G120001B
ORACOVER FERRARI RED 21-023#
ORACOVER GOLD 21-092#
ORACOVER BLACK 21-071#
ORACOVER SILVER 21-091#
H-G120001A
ORACOVER FERRARI RED 21-023#
ORACOVER WITH 21-010#
ORACOVER BLACK 21-071#
ORACOVER SILVER 21-091#
www.aeroplusrc.com [email protected]om
AeroPlus RC Copyright 2014 © All Rights Reserved
100-125CC Extra 330LT
Congratulations on your purchase of your new AeroPlus RC Extra 330LT. This plane
has been designed to be one of the lightest and highest performance aerobatics planes
anywhere. We hope that you will enjoy this plane and will exceed your expectations in
what a model airplane can be.
Thank you,
AeroPlus RC
Unpacking -
Carefully unpack the model, when opening the plastic bags make sure you do not to cut any covering on
the model. Inspect each item to make sure there was no damage in shipping. If for any reason you are
not happy with any part or are unsure please contact the Dealer that you purchased from.
Covering -
Because of the multiple climate zones encountered on the trip from the factory to you,
some of the covering may have wrinkles. We highly recommend that you take time to re-
seal all covering edges with an iron and to use a heat gun to remove any wrinkles and re-
tighten the covering. It is best to do this now while before the plane is assembled.
*Note: Be careful not let any heat get near parts like the canopy or cowl as this may cause
damage.
Assembly Tips
We also recommend that you go over all the accessible joints with cyano glue. Wick glue
into areas of high stress around the U/C plate and motor box.
Use a quality Thread-lock on all metal to metal joints. Even if your model is electric
powered with lower levels of vibration the thread-lock will ensure that things do not fall
off of your airplane!!
www.aeroplusrc.com [email protected]om
AeroPlus RC Copyright 2014 © All Rights Reserved
Landing Gear Assembly
To help prevent the fuselage from being damaged while the model is being
assembled we recommend fitting the landing gear first.
Note - Before beginning assembly be sure to determine your left and right wheels pants.
First, glue the thin wood wheel spacer to the inside of the wheel pant on what will be
the outer side of the pant. Use the bolt to help centre the spacer
Next, insert the bolt from what will be the outside of the wheel pant; put one thicker
wood spacer on to the axle bolt, followed by the wheel and one more wood spacer.
Install a lock nut onto the axle-bolt, followed by a washer.
Note- you must place the washer now as it will be impossible to place once the axle is
tightened. I use plastic servo horns drilled out in place of wood spacers for durability.
www.aeroplusrc.com [email protected]om
AeroPlus RC Copyright 2014 © All Rights Reserved
Tighten down the bolt holding the locknut.
Note –Do not over tighten. This will prevent the wheel from turning.
Insert the protruding bolts through the landing gear hole.
Tighten up using a washer and lock nut.
Repeat for other side.
This method takes time but is worth it as the wheel pants will last many flights.
Horizontal Stab
1. Now glue the control horns into the elevators.
a. First use a sharp hobby knife to remove the covering from the slots.
www.aeroplusrc.com [email protected]om
AeroPlus RC Copyright 2014 © All Rights Reserved
b. Before gluing the area on the horns that goes inside the elevator needs to be roughed up with
sandpaper. This allows a better glue joint.
c. Using Epoxy now glue the two control horns into their respective places.
Note: it is highly recommended to install a ball joint in between the control horns to maintain
proper spacing during gluing.
Note: also please take care to make sure the linkage whole in the control arm is on the hinge line.
2. Installing the elevator servos.
a. First test fit the servo into the servo mount. Some trimming make be required.
Note. Servo fits so spline is towards the front of the plane.
b. Now pre drill the servo mounts with a 1/16 drill bit, the secure the servo into the servo mount
with servo hardware.
www.aeroplusrc.com [email protected]om
AeroPlus RC Copyright 2014 © All Rights Reserved
c. Next remove the servo and use thin C.A. glue to reinforce the threads. After the glue is dry
reinsert the servo.
Note. Depending on servo arms used it may be necessary to install arm before reinstalling the servo.
d. Next install the servo linkages.
3. Extensions
a. Thread a 36” servo extension though the fuselage to the openings near the elevator.
www.aeroplusrc.com [email protected]om
AeroPlus RC Copyright 2014 © All Rights Reserved
b. Connect the servo to the extension but be sure to use a servo clip or a piece of heat shrink to
ensure it does not become disconnected during flight.
4. Installing Elevator Halfs
a. Install the small carbon tube into the fuselage.
b. Slide the Elevator Half onto the tube.
Note: make sure the servo wire goes cleanly inside the fuselage and is not pinched.
c. Attached the elevator half to the fuselage with the provided hardware.
M3×12 inner hexagon screw & M3 wrench
5. Repeat the process for the other elevator half.
www.aeroplusrc.com [email protected]om
AeroPlus RC Copyright 2014 © All Rights Reserved
Rudder
1. Remove the covering where the rudder horns push through with either a hobby knife or soldering
iron.
2. Test fit the rudder horns
Note: Be sure the rudder horns are equal on both sides and in line with the hinge
point this is very important!
3. Sand the area on the horn that fits inside the rudder so the glue bonds better.
4. Attaching the rudder.
a. Insert the easy removal pin into the pin hinges.
www.aeroplusrc.com [email protected]om
AeroPlus RC Copyright 2014 © All Rights Reserved
5. Glue the rudder horns in the rudder with epoxy; wipe off excess glue while it is wet.
Note: Use the ball joint and bolt while gluing to maintain alignment.
Note: While still movable measure that the same amount pushes out each side. Care needs to be taken here
otherwise your rudder geometry will be incorrect.
6. Installing the Rudder Servo
a. If using the included ruder arm assemble the rudder servo control arm as below, drill holes for
screws and use C.A. glue to stop the nuts from coming loose.
b. Fit the rudder servo and drill holes using a 1/16 drill bit for the servo screws, then drop thin C.A.
glue into the holes to strengthen the wood.
Note: besure the glue has fully cured before installing the servo again.
www.aeroplusrc.com [email protected]om
AeroPlus RC Copyright 2014 © All Rights Reserved
c. Using servo screws fix the servo in place, note the spline is towards the front of the plane.
7. Installing the rudder cables
a. Thread the cables though the fuselage from the rudder to the servo tray
b. Loop the cable though the crimp and attachment point as shown below.
c. Crimp the cable using a pair of pliers then trim cable.
Table of contents
Other AeroPlus Toy manuals
AeroPlus
AeroPlus MXS-R 30CC User manual
AeroPlus
AeroPlus Corvus Racer 540 User manual
AeroPlus
AeroPlus Edge 540 V3 35CC User manual
AeroPlus
AeroPlus Edge 540 V3 20CC User manual
AeroPlus
AeroPlus A?G030010A User manual
AeroPlus
AeroPlus YAK 55M User manual
AeroPlus
AeroPlus EXTRA 330SC 60CC User manual
AeroPlus
AeroPlus Corvus Racer 540 59 User manual
AeroPlus
AeroPlus Sbach 342 User manual
AeroPlus
AeroPlus Sbach 342 20CC User manual
