Advantech EDG-4100 Series Quick start guide

EDG-4100W Series User Note

USER NOTE: EDG-4100W Series

EDG-4100W

1-Port RS-232 to WLAN Data Gateway Embedded Module

EDG-4110W

1-Port RS-422/485 to WLAN Data Gateway Embedded Module

EDG-4100WDK

EDG-4100W, EDG-4110W development kits

User Note

The documentation and the software included with this product are copyrighted 2005 by

Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make

improvements in the products described in this manual at any time without notice. No part of this

manual may be reproduced, copied, translated or transmitted in any form or by any means without

the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended

to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use,

nor for any infringements of the rights of third parties, which may result from its use.

Acknowledgements

Intel and Pentium are trademarks of Intel Corporation. Microsoft Windows and MS-DOS are

registered trademarks of Microsoft Corp. All other product names or trademarks are properties of

their respective owners.

Part No. 2003410000 1st Edition

Printed in Taiwan, November 2005

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its products will be free from

defects in materials and workmanship for two years from the date of purchase.

This warranty does not apply to any products which have been repaired or altered by persons

other than repair personnel authorized by Advantech, or which have been subject to misuse,

abuse, accident or improper installation. Advantech assumes no liability under the terms of this

warranty as a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous testing, most of our

customers never need to use our repair service. If an Advantech product is defective, it will be

repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will

be billed according to the cost of replacement materials, service time and freight. Please consult

your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For example, CPU speed,

Advantech products used, other hardware and software used, etc.) Note anything abnormal and

list any onscreen messages you get when the problem occurs.

EDG-4100W Series User Note

2. Call your dealer and describe the problem. Please have your manual, product, and any helpful

information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return merchandize authorization)

number from your dealer. This allows us to process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card

and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A

product returned without proof of the purchase date is not eligible for warranty service.

5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer.

This product has passed the pretest of CE test for environmental specifications when shielded

cables are used for external wiring. We recommend the use of shielded cables. This kind of cable

is available from Advantech. Please contact your local supplier for ordering information.

FCC Class B

This equipment has passed the pretest of FCC and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the

interference at his or her own expense.

Technical Support and Assistance

1. Visit the Advantech web site at www.advantech.com/support where you can find the latest

information about the product.

2. Contact your distributor, sales representative, or Advantech’s customer service center for

technical support if you need additional assistance. Please have the following information ready

before you call:

- Product name and serial number

- Description of your peripheral attachments

- Description of your software (operating system, version, application software, etc.)

- A complete description of the problem

- The exact wording of any error messages

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the products from damage.

1. To avoid electrical shock, always disconnect the power from your PC chassis before you work

on it. Don’t touch any components on the CPU card or other cards while the PC is on.

2. Disconnect power before making any configuration changes. The sudden rush of power as you

connect a jumper or install a card may damage sensitive electronic components.

EDG-4100W Series User Note

Introduction

Description

EDG-4100W and EDG-4110W are fast and cost-effective 802.11b wireless networking-enabled

board modules. EDG-4100W provides one RS-232 port, while EDG-4110W provides one

RS-422/485 port. The modules enable nearly any device to communicate with 802.11b wireless

LAN and shared networks, and they allow those devices to be remotely monitored, managed, and

controlled. Functionally transparent and efficient, EDG-4100W and EDG-4110W provide a

complete software and hardware solution. The modules effectively eliminate the need for OEMs

and systems integrators to invest engineering resources to develop 802.11b wireless Ethernet

networking solutions, and reduce the time it takes to bring intelligent devices to market. Thus, the

modules are especially suitable to provide remote management and data accessibility to

thousands of devices that cannot connect to the network, such as factory machinery, security

systems, heating and ventilation systems, lighting control systems and Point-of-Sale devices.

EDG-4100W and EDG-4110W are 54 x 59mm wireless networking-enabled boards, so they can

easily fit into almost any device. A wireless antenna is provided to connect to the 802.11b wireless

LAN, and pin headers are provided to connect DI/O, power, and RS-232/422/485 into your boards.

There are also 8 DI/O slots, which allow additional flexibility.EDG-4100W and EDG-4110W

replace expensive dedicated PC’s and lengthy serial cables with fast, reliable networking

technology.

EDG-4100W and EDG-4110W also provide development kits to develop your own applications.

Using these kits, you could easily develop serial and/or DI/O applications on EDG-4100WDK.

EDG-4100WDK also comes with: a debug LED, driver CD, RS-232 loop back test connector,

RS-422 loop back test connector, a standard male DB9 connector, 8 channel DI/O slots on the

terminal block, a null modem cable, and a 100~240 VAC to 5 VDC power supply.

Features

•Supports 802.11b standard

•Supports Wireless LAN Ad-Hoc and Infrastructure modes

•Supports high transmission speeds up to 230 kbps

•Supports an advanced security mechanism to avoid unauthorized access

•Auto-reconnection

•Remote download of firmware

•Supports 4 digital input and 4 digital outputs

•Auto-detection

•Easily-managed Port Mapping Utility

•Supports Windows NT/2000/XP/XP2003 drivers

•Surge protection for RS-485 line and power supply

•Automatic RS-485 data flow control

EDG-4100W Series User Note

Specifications

•Protocol: TCP/IP

•Network: 802.11b

•Serial Ports: 1

•Serial Type: RS-232 (EDG-4100W)

RS-422/485 (EDG-4110W)

•Transmission Speeds: 50 bps ~ 230 kbps

•Parity Bits: Odd, even, none, space, mark

•Data Bits: 5, 6, 7, 8

•Stop Bits: 1, 1.5, 2

•Digital Input and Output:

Digital Input:

Logic level 0 : 0 ~ 4.2 V , close to GND

Logic level 1 : 4.4 ~5 V , open

Digital Output:

Open collector up to 30 V, 200mA Max load

•Utility Software:

Auto-detection configuration utility (up to 128 devices)

Port mapping utility

•Driver Support: Windows 98/NT/2000/XP/2003

•Power Requirement: 5 V DC

•Power Consumption: 2.5 W

•Operating Temperature: 0 ~ 55° C (32 ~ 131° F)

•Storage Temperature: -20 ~ 80° C (-4 ~ 176° F)

•Operating Humidity: 20 ~ 95% (non-condensing)

•Storage Humidity: 0 ~ 95% (non-condensing)

Packing list

Before setting up the system, check that the items listed below are included and in good condition.

If any item does not accord with the table, please contact your dealer immediately.

EDG-4100W or EDG-4110W

1 x EDG-4100W or EDG-4110W

1 x INET CD-ROM with industrial communication driver, utility and user manual

1 x EMI Dia. 7.8mm/L 82mm Wireless LAN antenna link with EDG-4100W and EDG-4110W

EDG-4100WDK

1 x EDG-4100W/EDG-4110W develop kit board

1 x AC/DC power adapter 100V ~ 240 VAC input, 5VDC output, 5W

1 x RS-232 loop-back connector

1 x RS-422 loop-back connector

1 x null modem cable

1 x INET CD-ROM with industrial communication driver, utility and user manual

Ordering Information

•EDG-4100W 1 port RS-232 to WLAN Data Gateway Embedded Module

•EDG-4110W 1 port RS-422/485 to WLAN Data Gateway Embedded Module

•EDG-4100WDK-A EDG-4100W/EDG-4110W development kits

EDG-4100W Series User Note

LED (only on EDG-4100WDK)

There is an LED status display located on the EDG-4100WDK.

LED Color Status Description

ON Blinking (1 time/sec)Work Green

OFF Not working

ON Data being transmitted or

received

WLAN Red

OFF No data action

Red/Green OFF/OFF 0 ~ 20% signal strength

Red/Green OFF/Half-On 20 ~ 40% signal strength

Red/Green OFF/Full-ON 40 ~ 60% signal strength

Red/Green Half-On/Full-

ON 60 ~ 80% signal strength

Signal1(Green)

Signal2(Red)

Red/Green Full-ON/Full-

ON 80 ~ 100% signal strength

ON Serial port data being

transmitted

SOUT Red

OFF Serial port no data being

transmitted

ON Serial port data being

transmitted

SIN Green

OFF Serial port no data being

transmitted

Dimensions

EDG-4100W Series User Note

Connectors

EDG-4100W/4110W have 2 connectors (CON2 and CON3), and the pin definitions are as follows:

EDG-4100W Series User Note

CON3 EDG-4100W EDG-4110W CON2 EDG-4100W/10W

Pin Description Description Pin Description

1 DI1 DI1 1 DO1

2 DI2 DI2 2 DO2

3 DI3 DI3 3 DO3

4 DI4 DI4 4 DO4

5 +5V +5V 5 SOUT LED

6 GND GND 6 SIN LED

7 RX - 7 WORK LED

8 TX - 8 WLAN LED

9 RTS RX+ 9 SIGNAL1 LED

10 DTR TX+ 10 SIGNAL2 LED

11 CTS - 11 +5V

12 DCD TX- 12 GND

13 HW reset HW reset

14 MODE MODE

15 DSR -

16 RI RX-

The EDG-4100WDK has 2 connectors (Serial DB9, power and DI/O), and the pin definition is as

follows:

DB9 Male

Pin RS-232 RS-422 RS-485

1 DCD Tx- Data-

2 Rx - -

3 Tx - -

4 DTR Tx+ Data+

5 GND GND GND

6 DSR - -

7 RTS Rx+ -

8 CTS - -

9 RI Rx- -

EDG-4100W Series User Note

Flexible Design and Easy-to-Manage S/W Support

EDG-4100W and EDG-4110W have been designed to be very flexible and easy-to-use to assist

OEM/ODM customers. EDG-4100W and EDG-4110W can easily fit to almost any serial device

available. EDG-4100 provides pin headers to connect the Wireless LAN, DI/O, power, and

RS-232/422/485 onto the customer’s own boards. EDG-4100W/4110W applies the same

configuration and COM port mapping utility as ADAM-4571W. When EDG-4100W/4110W, with

the EDG-4100WDK powered on, the utility will automatically detect the module as ADAM-4571W.

DI/O Function

Different from the ADAM-4571W, EDG-4100W and EDG-4110W also provide DI/O functions. Use

the UDP (port: 1024) command to control DI/O, which are divided into 2 categories. You also could

refer to the DI/O sample which is developed using Visual Basic®.

•Set DO status command:

Set the EDG-4100W/EDG-4110W’s DO status command. The command format is: #0100FF. FF

is hexadecimal, and the first F digit means to set the DO status, the second F digit is redundant but

must be sent to fulfill the protocol limit. For example, send command as: #01005F, binary of 5 is

0101 which means to set DO0 and DO2 to low, DO1 and DO3 to high.

•Read DI/O status command:

If the command: $016 is sent to the EDG-4100W/EDG-4110W, you will get the DI/O status

response: “!FF”. The “!” digit is the format character and FF is hexadecimal. The first F means D0

status, the second F means DI. For example: “!5A”, means the binary of 5 is 0101, which means

DO0 and DO2 are low, and DO1 and DO3 are high. The binary of A is 1010, which means DI0 and

DI2 are high, and DI1 and DI3 are low.

EDG-4100W Series User Note

Troubleshooting

Configuration Utility can not find EDG-4100W/4110W

This chapter explains how to solve some of the most common problems you could encounter while

using EDG-4100W/EDG-4110W. If you are still having problems after reading this chapter, contact

your dealer, or e-mail Advantech support for help.

1. Check the WORK LED. If it is off, make sure the EDG device power cable is plugged in, and

make sure the input voltage is set to +5V DC

2. Check the WLAN LED. If it is off, check to see if the wireless network connection is OK.

3. Check to see if the EDG-4100W/ EDG-4110W and the host are on the same LAN. Your host

and the EDG-4100W/ EDG-4110W should be set on the same mode, channel, SSID, and network

domain.

4. Check to see if the wireless AP’s signal is too weak, and if there are too many wireless AP’s in

your area.

5. Check to see if your wireless network needs an encryption key, and if so, set the encryption.

6. Refer pg.10 and pg.11 of the ADAM-4571W User Guide, under the section, “Diagnostic mode to

search EDG-4100W and EDG-4100W”, and try to set your wireless environment the same as the

diagnostic setting of EDG-4100W/ EDG-4100W.

This manual suits for next models

Table of contents

Other Advantech Control Unit manuals

Advantech

Advantech MIC-75M11 User manual

Advantech

Advantech PCM-3665 PC/104-Plus Installation and operation manual

Advantech

Advantech ADAM-6051 User manual

Advantech

Advantech MIO-6250 MIO/160 Installation and operation manual

Advantech

Advantech ADAM-6217 User manual

Advantech

Advantech PCM-3718 Series User manual

Advantech

Advantech ADAM-3656 Installation and operation manual

Advantech

Advantech AMAX-175 Series User manual

Advantech

Advantech PCM-3526 Installation and operation manual

Advantech

Advantech SOM-5892 User manual

Advantech

Advantech PCM-3345 User manual

Advantech

Advantech INTRAC INTRAC-305 Instruction Manual

Advantech

Advantech PCM-23C1CF User manual

Advantech

Advantech SOM-5893 User manual

Advantech

Advantech PCM-24BXWF Installation and operation manual

Advantech

Advantech ADAM-3016 User manual

Advantech

Advantech PCM-3643 Installation and operation manual

Advantech

Advantech WISE-4610 Series Installation and operation manual

Advantech

Advantech ADAM-5000 Series User manual

Advantech

Advantech PCM-261 Installation and operation manual

Advantech

Advantech AIW-357 DK-G1P User manual

Advantech

Advantech PCM-233A Installation and operation manual

Advantech

Advantech WISE-4671 Installation and operation manual

Advantech

Advantech B+B SmartWorx iMcV-Giga-MediaLinX TX/SFP User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual