ADTRAN 1203019L2 User manual
NT1 ACE
USER MANUAL
1203019L1: NT1 ACE with Power Supply
1203019L2: NT1 ACE
1203019L3: NT1 ACE International
336048VUR-2: Power Supply
61203019L1-1D
January 1999
FCC ID: HDC1203019L1
This device complies with Part 15 of the FCC rules. Op-
eration is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications to this unit not ex-
pressly approved by the party responsible for
compliance could void the user's authority to op-
erate the equipment.
Canadian Standards Association
This device must be powered by a CSA approved power
supply or a power supply meeting the requirements of
CS03, Part I Section 1.4.2.
Warranties
ADTRAN will repair or replace this product within five years
from the date of shipment if it does not meet its published spec-
ifications or fails while in service. For detailed warranty, repair,
and return information, refer to the ADTRAN Equipment War-
ranty and Repair and Return Policy Procedure. Return Material
Authorization (RMA) is required prior to returning equipment
to ADTRAN. (See inside back cover for phone and address.)
901 Explorer Blvd.
P. O. Box 140000
Huntsville, AL 35814-4000
Phone: (256) 963-8000
©1999 ADTRAN, Inc.
All rights reserved
Printed in USA
61203019L1-1 NT1 ACE User Manual iii
FCCregulationsrequirethatthefollowinginformationbe
provided in this manual:
1. This equipment complies with Part 68 of the
FCC rules. On the bottom of the equipment
housing is a label that shows the FCC registration
number for this equipment. If requested, provide
this information to the telephone company.
2. If this equipment causes harm to the telephone
network, the telephone company may temporarily
discontinue service. If possible, advance notifica-
tionisgiven;otherwise,notificationisgivenassoon
aspossible. Thetelephonecompanywilladvisethe
customer of the right to file a complaint with the
FCC.
3. Thetelephonecompanymaymakechangesinits
facilities,equipment,operations,orproceduresthat
couldaffecttheproperoperationofthisequipment;
advance notification and the opportunity to main-
tain uninterrupted service is given.
4. If experiencing difficulty with this equipment,
please contact ADTRAN for repair and warranty
information. The telephone company may require
this equipment to be disconnected from the net-
iv NT1 ACE User Manual 61203019L1-1
work until the problem is corrected, or it is certain
the equipment is not malfunctioning.
5. This unit contains no user-serviceable parts.
6. An FCC compliant telephone cord with a modu-
lar plug is provided with this equipment. In addi-
tion, an FCC compliant cable appropriate for the
dial backup option ordered is provided with this
equipment. This equipment is designed to be con-
nectedtothetelephonenetworkorpremiseswiring
using an FCC compatible modular jack, which is
Part 68 compliant.
7. The following information may be required
when applying to the local telephone company for
leased line facilities.
Service
Type Digital Facility
Interface Code Service
Order Code Network
Jacks
ISDN 02IS5 6.0N RJ-49C
61203019L1-1 NT1 ACE User Manual v
ADTRAN YEAR 2000 (Y2K)
READINESS DISCLOSURE
ADTRAN has established a Year 2000 program to ensure
that our products and operations will correctly function
in the new millennium. ADTRAN warrants that all prod-
ucts meet Year 2000 specifications regardless or model or
revision. Information about ADTRAN’s Year 2000 com-
pliance program is available at the following:
Web Site www.adtran.com
Product Matrix www.adtran.com/Y2Kfax.html
Faxback Document Line (256) 963-8200
Y2K plans and product certifications
are listed in the matrix
Y2K Project Line (256) 963-2200
E-mail year 2000@adtran.com
vi NT1 ACE User Manual 61203019L1-1
CANADIAN EMISSIONS REQUIREMENTS
This digital apparatus does not exceed the Class B limits
for radio noise emissions from digital apparatus as set
out in the interference-causing equipment standard enti-
tled "Digital Apparatus," ICES-003 of the Department of
Communications.
Cet appareil numerique respecte les limites de bruits
radioelectriques applicables aux appareils numeriques
de Class B prescrites dans la norme sur le materiel brouil-
leur: "Appareils Numeriques," NMB-003 edictee par le
ministre des Communications.
CANADIAN EQUIPMENT LIMITATIONS
Notice: The Canadian Industry and Science Canada label
identifies certified equipment. This certification means that
the equipment meets certain telecommunications network
protective, operational, and safety requirements. The
Department does not guarantee the equipment will operate
to the user’s satisfaction.
Before installing this equipment, ensure that it is permis-
sible to be connected to the facilities of the local telecom-
munications company. The equipment must also be
installed using an acceptable method of connection. In
61203019L1-1 NT1 ACE User Manual vii
some cases, the company’s inside wiring associated with
a single-line individual service may be extended by
means of a certified connector assembly (telephone
extension cord). Compliance with the above conditions
may not prevent degradation of service in some situa-
tions.
Repairs to certified equipment should be made by an
authorized Canadian maintenance facility designated by
the supplier. Any repairs or alterations made by the user
to this equipment, or equipment malfunctions, may give
the telecommunications company cause to request the
user to disconnect the equipment.
Users should ensure for their own protection that the
electrical ground connections of the power utility, tele-
phone lines, and internal metallic water pipe system, if
present, are connected together. This precaution may be
particularly important in rural areas.
Users should not attempt to make such
connections themselves, but should contact
the appropriate electric inspection author-
ity, or an electrician, as appropriate.
viii NT1 ACE User Manual 61203019L1-1
The Load Number (LN) assigned to each terminal device
denotes the percentage of the total load to be connected
to a telephone loop which is used by the device, to pre-
vent overloading. The termination on a loop may consist
of any combination of devices subject only to the require-
ment that the total of the Load Numbers of all devices
does not exceed 100.
61203019L1-1 NT1 ACE User Manual ix
AFFIDAVIT REQUIREMENTS FOR CONNECTION
TO DIGITAL SERVICES
• An affidavit is required to be given to the tele-
phone company whenever digital terminal
equipment without encoded analog content
and billing protection is used to transmit digi-
tal signals containing encoded analog content
which are intended for eventual conversion
into voiceband analog signals and transmitted
on the network.
• The affidavit shall affirm that either no encod-
ed analog content or billing information is be-
ingtransmittedorthattheoutputofthedevice
meets Part 68 encoded analog content or bill-
ing protection specifications.
• End user/customer will be responsible to file
an affidavit with the local exchange carrier
when connecting unprotected CPE to a 1.544
Mbps or subrate digital services.
• Until such time as subrate digital terminal
equipment isregistered forvoice applications,
the affidavit requirement for subrate services
is waived.
x NT1 ACE User Manual 61203019L1-1
AFFIDAVIT FOR CONNECTION OF CUSTOMER
PREMISES EQUIPMENT TO 1.544 MBPS AND/OR
SUBRATE DIGITAL SERVICES
For the work to be performed in the certified ter-
ritory of _______________
(telco name)
State of __________________
County of ________________
I, ______________________________(name),
________________________(business address),
______________________ (telephone number) be-
ing duly sworn, state:
I have responsibility for the operation and maintenance
of the terminalequipment to beconnected to 1.544 Mbps
and/or ________ subrate digital services. The terminal
equipment to be connected complies with Part 68 of the
FCC rules except for the encoded analog content and bill-
ing protection specifications. With respect to encoded
analog content and billing protection:
( ) I attest that all operations associated with the estab-
lishment, maintenance, and adjustment of the digital
CPEwithrespecttoanalogcontentandencodedbilling
protection information continuously complies with
Part 68 of the FCC Rules and Regulations.
This manual suits for next models
4
Table of contents
Other ADTRAN Network Hardware manuals
ADTRAN
ADTRAN NetVanta E1/FE1 + G.703 Network Interface... User manual
ADTRAN
ADTRAN T200 IDSL Instruction Manual
ADTRAN
ADTRAN ATM Mini-DSLAM User manual
ADTRAN
ADTRAN QDFR Unit Instruction Manual
ADTRAN
ADTRAN Express 3000 User manual
ADTRAN
ADTRAN T200 SHDSL User manual
ADTRAN
ADTRAN NetVanta 834 Owner's manual
ADTRAN
ADTRAN Total Access Octal ADSL User manual
ADTRAN
ADTRAN Total Access 1248 User manual
ADTRAN
ADTRAN BR1/10 PAU Instruction Manual
ADTRAN
ADTRAN TOTAL ACCESS 1200 User manual
ADTRAN
ADTRAN ISU 128 User manual
ADTRAN
ADTRAN NetVanta 5660 User manual
ADTRAN
ADTRAN SLC-5 U-BR1TE III Instruction Manual
ADTRAN
ADTRAN NETVANTA 6355 User manual
ADTRAN
ADTRAN NetVanta 8044M User manual
ADTRAN
ADTRAN SHDSL V.35 LTU User manual
ADTRAN
ADTRAN ESU LT User manual
ADTRAN
ADTRAN Network Interface Module T1/FT1 User manual
ADTRAN
ADTRAN TRACER 5045 User guide
Popular Network Hardware manuals by other brands
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL product manual
B&B Electronics
B&B Electronics ZXT9-IO-222R2 product manual
Yudor
Yudor YDS-16 user manual
D-Link
D-Link ShareCenter DNS-320L datasheet
Samsung
Samsung ES1642dc Hardware user manual
Honeywell Home
Honeywell Home LTEM-PV Installation and setup guide
